schmersal AZ 01 User manual

AZ
Operating instructions
Door contacts
EN 1
Product description
Door contacts serve as a functional component for monitoring the door
position or the locking device in the elevator. With the switchgear, the
switching element and actuator are not connected to each other in
terms of the design. However, when they are switched they are joined
together functionally or separated. When the safety device is opened,
the actuator is separated from the base device. Here, the NC contact of
the door contact is opened through positive breaking.
Technical information can be found in the Schmersal
catalogues or in the online catalogue on the Internet:
www.schmersal.net.
The currently valid declaration of conformity can be
downloaded from the internet at www.schmersal.net.
Construction in principle
The following figures show, in principle, the construction and function
of door contacts in the various designs. Further technical details can
be found in the Schmersal catalogues or in the online catalogue on the
Internet at www.schmersal.net
Mounting
The fixing screws of the switchgear must be protected against
unauthorised tampering. The enclosure must not be used as an end
stop.
Electrical connection
Wires are to be connected and tightened to the respective torque.
Provision must be made for the necessary strain relief.
Information about the cable sections, torque settings and
switch travel can be gleaned from the Schmersal catalogues
and the online catalogue on the internet at www.schmersal.net.
Set-up and maintenance
The function of the component must be tested. The following conditions
must be previously checked and met:
1. Check the switch enclosure for damage
2. Check for free movement of the actuating element
3. Check the integrity of the cable entry and connections
We recommend carrying out a visual inspection and functional test at
regular intervals.
Damaged or defective components must be replaced.
Disassembly and disposal
The switchgear may only be removed when de-energised,
professionally and in accordance with national rules and regulations.
About this document
This operating instructions manual provides all the information required
for the mounting, set-up and commissioning to ensure the safe
operation and disassembly of the safety switchgear. The operating
instructions must be available in a legible condition and a complete
version in the vicinity of the device.
All operations described in this operating instructions manual must
be carried out by trained specialist personnel, authorised by the plant
operator only.
Selection and installation of the s witchgear as well as its inclusion in
a control system require that the plant manufacturer have qualified
knowledge of the relevant legislation and normative requirements.
General safety instructions
The user must observe the safety instructions in this operating
instructions manual, the country specific installation standards as well
as all prevailing safety regulations and accident prevention rules.
The information contained in this operating instructions manual is
provided without liability and is subject to technical modifications.
Warning about misuse
In case of inadequate or improper use or manipulations of
the component, personal hazards or damage to machinery or
plant components cannot be excluded.
Exclusion of liability
We shall accept no liability for damages and malfunctions resulting from
defective mounting or failure to comply with this operating instructions
manual. The manufacturer shall accept no liability for damages
resulting from the use of unauthorised spare parts or accessories.
For safety reasons, invasive work on the device as well as arbitrary
repairs, conversions and modifications to the device are strictly
forbidden; the manufacturer shall accept no liability for damages
resulting from such invasive work, arbitrary repairs, conversions and/or
modifications to the device.
KAS 103012698 / ACE 583894 / SISS 103027637 / SIPL 103027639 – 04.2019 / B
EN Operating instructions. . . . . . . . . . . . .pages 1 to 2
Original

2
Operating instructions
Door contacts AZ
EN
K.A. Schmersal GmbH & Co. KG
Möddinghofe 30, 42279 Wuppertal
Germany
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: www.schmersal.com
ACE Schmersal
Eletroeletrônica Industrial Ltda.
Av. Brasil, nº 815, Jardim Esplanada
CEP: 18550-000, Boituva – SP
Brazil
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: www.schmersal.com.br
SCHMERSAL
Industrial Switchgear (Shanghai) Co., Ltd.
Cao Ying Road 3336
201712 Shanghai / Qingpu,
P.R.CHINA
Phone [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: www.schmersal.com.cn
Schmersal India Private Limited
G-7/1, MIDC, Ranjangaon
Taluka Shirur, Dist. Pune – 412 220
Maharashtra
India
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: http://www.schmersal.in
AZ 01 AZ 02
50
41
35
14
9
4,5
4
616
(21)
¤ 4
10
7
5(10)
30
2(7) 2(7)
7
38
50
17
50
41
35
13
4,5
9
10
38
30
eingeschaltet
4
10
7
50
17
6
4
16
14
AZ 05 AZ 06, AZ 07
30
30
7,5
22,5
40
72
12
40
60
40
8
6
6
22
19
10
26
3
Actuator length 18 mm: H = 14 mm
21 mm: H = 17 mm
23 mm: H = 20 mm
222
12
19
29
41
¤5
14
18(21,23)
13
6
H
60
40
AZ 051, AZ 052, AZ 053 AZ 061, AZ 062, AZ 063, AZ 066
30
30
7,5
22,5
40
40
50
13
27
Actuator length 18 mm: H = 14 mm
21 mm: H = 17 mm
23 mm: H = 20 mm
29
41
¤5
14
18(21,23)
13
6
H
50
40
5
14
0,5
12,5
27
25
AZ 13, AZ 14-1 AZ 19
36
14
25
8
61
44
12
6
12
AZ14B/18
19
29
41
¤5
14
18(21,23)
13
6
39
50
10,5
37,4
40