Schrack Technik HSATS516ER User manual

WInstruction sheet: Sat Multiswitch 5 in 16, HSATS516ER
PAGE 1/2
INSTRUCTION SHEET: HSATS516ER_E / 07-2021
Errors and omissions excepted.
SCHRACK TECHNIK GMBH
Seybelgasse 13, A - 1230 Vienna, PHONE [phone]
E-MAIL [email protected], INTERNET www.schrack.com
wSchrack-Info
• No loss at SAT-range
High modulation / high signal-quality•
Low power consumption•
Short-circuit proof•
Made in Germany•
wUsage
Multiswitch HSATS516ER distributes the signals of your satellite system to up to 16 devices (satellite receiver, TV sets with
satellite tuner, etc.).
The HSATS516ER has a built-in 22 kHz generator and can be used with a Quattro or Quad LNB.
Using a Quattro LNB, make sure that vertical/horizontal and low/high band signals are connected correct.
The 4 outputs of the Quad LNB can be connected to any Sat input of the switch.
The terrestrial input is designed for using with a DVB-T / FM antenna.
wSafety Instructions
Please check first the coaxial cable regarding short circuit before starting!
The mounting ground should be:
• even and flame proof
dust-free•
protected against humidity•
not under direct impact of sunlight•
not adjacent to heating sources•
The ventilation slots of the power supply unit may not be covered.
It is to be paid attention to it that the input levels of the SAT-lines are equivalent high.
All installation and fixing of components should only be executed when the units are disconnected from the mains
supply. Avoid short-cricuits.
The applicate standards and regulations for the guarantee of electrical security are to be considered.
The national regulations for broadcast recording systems have to be observed!
The electrical system for powering the device, e.g. B.
House installation must comply with EN 62368-1 protective devices
against excessive currents, earth faults and short circuits.
The power supply plug serves as a disconnect device from the mains voltage in service and in the event of danger and
must therefore be accessible and usable at all times.
After connection to the mains voltage, the device is in operation.

PAGE 2/2
INSTRUCTION SHEET: HSATS516ER_E / 07-2021
Errors and omissions excepted.
SCHRACK TECHNIK GMBH
Seybelgasse 13, A - 1230 Vienna, PHONE [phone]
E-MAIL [email protected], INTERNET www.schrack.com
DESCRIPTION ORDER NO.
HSATS516ERSAT Multiswitch 5 in 16, for Quattro LNB, also for Quad LNB, internal PSU
wInstallation
First connect the HSATS516ER with all external devices (antennas,
receivers, LNB) and do not forget grounding of the device. Use the
GND terminal for earth connection. After that you can plug in the
power cord into the mains. The indicator next to the GND
terminal should lit.
HSATS516ER with PSU and Quattro / QUAD LNB
wTechnical Data
Typ: HSATS51 6 ER
Description
Inputs SAT
Terr.
Outputs
tap loss
SAT
Terrestrial
Isolation
H / V
SAT / Terr.
Return loss
Input / Output
Output level
SAT IMA3 35 dB
Terr. IMA3 60 dB
22 kHz generator
Selection
Remote current LNB
Main voltage
Power consumption
Dimensions
Weight
with PSU, 22kHz Generator
for Quad and Quattro LNB
4 x 950 x 2200 MHz
1 x 40 x 860 MHz
16 x 40 - 2200 MHz
-1...+3 dB ±1,5 dB
>30 dB
>25 dB
<-10dB
max. 0 dBµV
integrated
14V/18V, 0/22kHz
max. 500 mA
100 - 230 V AC, 50 - 60 Hz
max. 5,0 W
220 x 112 x 58 mm
0,4 kg
2 dB ± 2 dB
max. 0 dBµV9
10