Schumacher Racing Cars ICON User manual

S1571ISS1
Instruction Manual

E.S.C
Motor
Servo
CR044 Curved Body Scissors
U3107 - Solder
Soldering Iron
CR266 40w
CR275 80w
U4229 Steel Spanner - 5.5mm/3.9mm
IMPORTANT SAFETY NOTES
We strongly recommend that anyone driving RC cars, or organising events, should obtain third
party liability insurance. In the UK this can be done by joining the BRCA. www.brca.org
This product is not suitable for children under the age of 14, without the direct
supervision of a responsible adult.
Select an area for assembly that is away from the reach of small children.
The parts in this kit are small and can be swallowed by children causing choking
and possible internal injuries.
Exercise care when using hand tools and sharp instruments during assembly.
Carefully read all manufacturers warnings and cautions for any additional items
used in the construction.
In line with our policy of continuous development the exact details of the kit may vary.
DO NOT use this car on public roads or in places where it can interfere with
traffic, people or animals.
Always check the operation of the radio with the wheels off the ground, before
using the car.
Make sure the radio and car batteries are fully charged before use.
Disconnect and remove the battery from the car when not in use.
Always store and charge LiPo batteries in a fireproof container.
DO NOT put fingers or any objects inside rotating or moving parts as this may
cause injury.
Make sure the charger is correctly set for the type of battery you are using.
Incorrect charging may cause a fire.
Insulate all exposed electrical wiring. Exposed or damaged wires can cause
short circuits and fire.
The motor and speed controller can become hot during use.
DO NOT touch them immediately after using your car as this may cause injury.
















CR233
Piston Drilling Kit
1.1-1.8mm (8 bits)
AM701011 - Low Profile 4mm Connector 24K - pk2
AM701012 - Low Profile 5mm Connector 24K - pk2
SK-100149
SKY RC e680 AC/DC 80W Charger
Pinion
2S Shorty
Li-Po Battery
AM110115 Allen Wrench 1.5
AM110120 Allen Wrench 2.0
AM110125 Allen Wrench 2.5
AM110130 Allen Wrench 3.0
AM150155 Nut Driver 5.5 (M3)
AM150170 Nut Driver 7.0 (M4)
AM190003 Reamer With End Cap For Lexan Body
Tyres and Inserts
CR522 CORE RC
Pro Tyre Glue + 2 Nozzles
CORE RC Paint
CR600 to CR631
CR666 to CR672
Schumacher Racing stocks and
distributes the following
manufacturers products and full
product listings are
available on our website at
www.racing-cars.com
PLEASE NOTE THAT SOME OF THE
PRODUCT RANGES BELOW ARE ONLY
AVAILABLE IN THE UNITED KINGDOM.
LC RACING
CR115
CORE RC Silicone Wire 12AWG Red/Black/Blue 50cm
Page 1
Additional Items Required

Use the M3x12 Cap head
screw and washers to fit the
inserts.
Tighten the screw until
the M3 thread insert is
pulled into the carbon fibre
part as shown.
M3 x 6
x 7
M3 x 25 x 1
M3 Nut
x 1
CR520
M3 Thread Insert
x 2
M3 x 6
x 2
M3 x 8
x 2
M3 x 6
x 4 M3 x 8
x 2
M2.5 x 8
x 1
Black 2.0 mm
x 2
M3 x 12 x 1
M3 Washer
x 3
Step 1
Page 2
Step 2

M3 x 4
x 2
M3 x 6
x 2
M3 Thread Insert
x 4
x 3
Low Ball Ultra Short
M3 x 6
x 4
M3 x 6
x 1
M3 x 6
x 2
M3 x 8
x 2
Ball Stud Short
x 1
CR520
CR520
Step 3
Page 3
Step 4

Leave loose for now.
1.00mm
M2.5 x 8
x 4
M3 x 8
x 4
M3 x 6 Patched
x 2
x 2
Low Ball Ultra Short
M3 Thread Insert
x 8
Black 2.0 mm
x 4
Step 5
Page 4
Step 6
A

Screw supplied with servo.
Servo not included.
Set 90° at neutral.
M3 x 8
x 2
M3 x 6
x 2
M3 x 8
x 4
M3 Nyloc
x 1
x 1
Ball Stud Ultra Long
Black 3.0 mm
x 1
Step 6
Page 5
Step 7
B

NOTE
Use the 12mm screw when using
5-7mm of spacers.
Use the 10mm screw when using
3-4.75mm of spacers.
Make sure the O’Ring is
fitted correctly.
M3 x 12
x 6
M3 x 6
x 6
Black 0.5 mm
x 4 O`ring x 2
M3 x 10
x 6
Step 8
Page 6
Step 9

The king pin may be a tight fit
in the hub carriers.
Gold front spring.
The hub carriers must touch
the king pin stops.
e’clip
x 2
M3 Nyloc
x 2
Black 0.5 mm
x 2
Black 1.0 mm
x 2
Low Ball Short
x 2
SILICONE
OIL 30000
SILICONE
OIL 30000
Step 10
Page 7
Step 11

Adjust for minimum clearance
with no drag.
Do NOT overtighten.
More Caster
Less Caster
Moving the camber strap
forwards and rearwards
adjusts the caster angle.
For more information
on caster angle see
car settings page 26.
NOTE
These spacers MUST equal
the ride height spacers.
NOTE
Check the screw lines up with
the post before tightening.
O`ring x 2
M3 Thread Insert
x 4
M3 Nyloc
x 1
x 4
Low Ball Ultra Short
Black 4.0 mm
x 1
ø4 x ø8 x 3
x 2
M3 x 6
x 1
M3 x 8
x 2
M3 x 12
x 1
M3 x 10
x 2
M3 x 6
x 2
M3 x 6
x 2
Black 0.75 mm
x 4
Black 4.0 mm
x 1
M3 x 25 x 1
CR520
Black 1.0 mm
x 1
SILICONE
OIL 30000
SILICONE
OIL 30000
Step 12
Page 8
Step 13

LH Thread
RH Thread
Note the shape of the turnbuckle.
This side is the left hand thread.
Right Hand Trackrod
Left Hand Trackrod
LH Thread
RH Thread
Longer Link
Shorter Link
21.00mm
Screwing the sockets onto the
turnbuckle, until no threads are
visible, and then undoing them to
the desired length allows for easier
adjustment on the car.
Greasing the threads will also help.
Steering Link
17.00mm
Step 14
Page 9
Step 14
A
B

NOTE
Correct disk spring
assembly.
NOTE
Correct thrust washer
assembly.
DIFF SETTING
Very gradually tighten the nut
until diff action begins.
Then tighten the nut 360° more.
This setting should be good
for most conditions.
M3 Nyloc
x 1
ø1/4” x ø3/8”
x 2
1/4”x 5/16” x 0.10mm
x 2
x 5
Disc spring washer
3.25 x 7.9 x 0.5
Grooved Small Washer
Grooved Large Washer
Thrust Washer
ø1/4” x ø3/8”
x 1
x 12
ø1/8”
Step 15
Page 10
Step 16

After tightening this screw, ensure
the axle rotates freely.
The axle spacers can be used to adjust
the rear track width of the car.
1/4” x 3/8”
Flanged
x 2
Axle Spacer
1/4”x 0.5
x 2
M3 x 8
x 6
M2.5 x 10
x 1
Step 17
Page 11
Step 18

Make two side dampers the same.
Use both extenders when running the car
in the optional long wheelbase position.
SILICONE
OIL 12000
SILICONE
OIL 30000
M3 x 14
x 3
Black 3.0 mm
x 1
Step 19
Page 12
Step 19
A
B

1 Dot
Low
Position
3 Dot
High
Position
2 Dot
Medium
Position
Mark and drill your body
to diameter 6.0mm for the
body posts.
Select the correct body
washer to fine tune the
bodyshell height.
Each incremental change
is 1.2mm.
Select the correct pin height
for your bodyshell.
Snap the body washers
onto the pins.
The bodyposts may be trimmed for
looks and aerodynamics. A sharp
knife or side cutters may be used.
Alternatively use AM190041 -
Arrowmax Body Post Trimmer
M4 Nyloc
x 2
M4 x 18 x 2
ø1.5 x 11.8
x 3
M3 x 10
x 2
M3 x 16 x 1
Step 20
Page 13
Step 21
A

Assemble the wing as shown before
assembling it to the car.
M3 Nyloc
x 2
M3 x 6
x 2
M3 x 6
x 2
M3 x 12
x 2
Step 21
Page 14
Step 22
B
A

Page 15
Step 22
B
Assembled Car

Adjust for minimum clearance
but free rotation.
Do NOT overtighten.
M4 Nyloc
x 4
ø5 x ø10 x 4
x 4
x 4
ø5 x ø7 x 0.40
Page 16
Step 23

Motor NOT included.
ESC NOT included.
LiPo NOT included.
Receiver NOT included.
Transponder NOT included.
Pinion NOT included.
Adjust the gear mesh to be as close
as possible without binding.
M3 x 6
x 1
M3 x 10
x 2
Black 1.0 mm
x 2
Servo Tape x 1
x 1
M3 x 4
Page 17
Step 24

Electric - Off Road Cars
K189 Icon - Formula 1 - Kit
Chassis Parts
U119 Aerial Tube - Pack 4
U4222 Turnbuckle Adjuster HTT - 39mm - pr
U4298 Turnbuckle HT - 35mm - pr
U4327 Alloy Servo Mount Black - K1/Mi5
U4627 Chassis Post Long - SS GT/At/Ecl
U4710 Alloy Servo Post - GT12-1/12th (pr)
U4741 6mm Offset Servo Arms
U4773 Aerial Mount - CAT K2
U4849 Steering Arm Posts - Atom (pr)
U4950 Body Posts - Eclipse (4pcs)
U7488 Lipo O Ring - Eclipse 2 - (pk6)
U7864 Vertical Top Deck Posts - Mi7 (pr)
U7870 Hub Carriers - Atom 2 (pr)
U7891 Alloy Lock Stop - Atom 2 - pr
U7938 Chassis Post 8mm - Eclipse 3 (pr)
U8074 C/F Chassis - Icon
U8075 C/F Front Wishbone - Icon (pr)
U8076 C/F Camber Strap (2 deg) - Icon
U8077 C/F Ride Height Spacer - Icon (pr)
U8078 C/F Side Link Mount - Icon (pr)
U8079 C/F Side LiPo Stop - Icon (pr)
U8080 C/F Multi Mount - Icon
U8081 C/F Damper Mount - Icon
U8082 C/F Pod Rear Brace - Icon
U8083 C/F Pod Base - Icon
U8084 C/F Radius Arm - Icon
U8085 C/F Wing Mount Upper - Icon
U8086 C/F Wing Mount Lower - Icon
U8114 Alloy Steering Housing - Icon
U8118 Front Body Post - Icon
U8134 Manual - Icon
U8160 Steering Pivot - Icon
Bodyshells and Decals
MT010003 Montech F1 Electric Car 1/10 F1J Body
MT011003 Montech F1 Electric Car 1/10 F2011 Body
MT013012 Montech F1 Electric Car 1/10 F13 Body
MT015006 Montech Wing F1 Front Black
MT015007 Montech Wing F1 Rear Black
MT015008 Montech Wing F1 Rear White
MT015009 Montech Wing F1 Front White
MT017003 Montech F1 Car Body - F17
MT017006 Montech F1 2017 Front Wing Black
MT017007 Montech F1 2017 Front Wing White
MT018009 Montech F18 F1 Body
U8135 Decals - Icon
Suspension
U4274 Pro Ball Stud Short - pk4
U4302 Ball Socket Short (Black) - Mi5 - pk4
U4700 Pro Ball Stud - Ultra Long - (pk4)
U4847 Rear Spring Seat - At/Ecl
U4851 Side Spring Seat (pr) - Atom/Eclipse
U4968 Ball Sockets Low Profile -Eclipse - pk4
U7787 Shock Top Ball Dia 5.5mm - Mi7 (pk4)
U7832 Ball Stud Low (Ultra Short) (pk4)
U7833 Ball Stud Low (Short) (pk4)
U7871 Pivot Mouldings - Atom 2
U7872 Side Link - Atom 2 (pr)
U8087 Alloy Damper Body - Icon
Suspension Cont....
U8088 Damper Rod - Icon
U8115 Front King Pin - Icon (pr)
U8116 Front Axle - Icon (pr)
U8117 King Pin Spacer - Icon (pr)
U8136 Pivot Ball Assembly - Icon (pr)
Transmission
CR509 Kimbrough - Thin Pro/Gear 88T - 64DP-#709
U4112 S/Steel Shims 1/4x5/16x0.10 pk6
U4808 "1/8"" Chrome Steel Ball -At/Ecl - pk12"
U4855 Diff Washer - Atom/Eclipse - pr
U4861 Diff Rebuild Kit - Atom/Eclipse
U4972 Ride Height Adjusters- 0.00, 0.50, 1.00, 1.50 4prs
U4973 Ride Height Adjusters- 0.25, 0.75, 1.25, 1.75 4prs
U4974 LH Wheel Clamp - Eclipse
U7883 Steel Diff Axle - Atom 2
U7899 Diff Spacer Set - Atom 2
U8104 Wheel Hex Clamp - Icon
U8112 Alloy Trans Housing RH - Icon
U8113 Alloy Trans Housing LH - Icon
U8120 Alloy Washer Carrier RH - Icon
Bearings and Balls
U2148 Ball Bearing - 5x10x4 Shield - (pr)
U3075 Ball Bearing - 4x8x3mm Red Seal - (pr)
U4809 Ball Bearing - 1/4x3/8x1/8 Shield - (pr)
U4980 Ball Bearing - 1/4x3/8x1/8 Flanged Shielded - (pr)
Springs
U4838 Rear Springs Black - Soft - At/Ecl - pr
U4839 Rear Springs Silver - Med/Soft - At/Ecl - pr
U4840 Rear Springs Gold -Med/Hard - At/Ecl - pr
U4841 Rear Springs Nickel - Hard - At/Ecl - pr
U4846 Spring Tuning Set Rear - At/Ecl
U7322 Rear Spring Red Dot-Hard/Ultra-Atom/Eclipse-pr
U7323 Rear Spring Black - Ultra - Atom/Eclipse - pr
U7886 Front Spring Black Soft - Atom 2 (pr)
U7887 Front Spring Silver Medium - Atom 2 (pr)
U7888 Front Spring Silver Medium - Atom 2 (pr)
U7889 Front Spring Gold Super Hard - Atom 2 (pr)
U7890 Front Spring Tuning Set (4prs) - Atom 2
Hardware
U1549 SPEED PACK - M4 Nuts and Washers
U1551 SPEED PACK - E Clips -2 x 8pcs
U1552 SPEED PACK - R Clips
U1606 SPEED PACK - Servo Tape - 30pk
U2128 SPEED PACK - Grub-Set Screws M3 M4
U3021 SPEED PACK - M3x6 Csk Hd - (pk10)
U3022 SPEED PACK - M3x8 Csk Hd - (pk10)
U3023 SPEED PACK - M3x10 Csk Hd - (pk10)
U3572 SPEED PACK - M3x14 Grub Screw pk4
U4124 SPEED PACK - Shims 5 x 7 x 0.4mm - pk6
U4155 SPEED PACK - M3 Csk Washers - Black Alloy (pk10)
U4241 SPEED PACK - M3 Alloy Nyloc Nuts - Black - pk10
U4650 SPEED PACK - M3 Nyloc Nut Steel - Black (10pcs)
U4835 SPEED PACK - M3 Steel Nut Black (pk8)
U4837 SPEED PACK M2.5x10 Cap Hd (pk8)
U4862 Black Alloy Washers 0.50mm (pk12)
Page 18
Spares List 1

Hardware Cont....
U4987 SPEED PACK Needle Roller 1.5x11.8 (pk8)
U7102 SPEED PACK - M3x4 Button Hd (pk10)
U7103 SPEED PACK - M3x6 Button Hd (pk10)
U7104 SPEED PACK - M3x8 Button Hd (pk10)
U7105 SPEED PACK - M3x10 Button Hd (pk10)
U7106 SPEED PACK - M3x12 Button Hd (pk10)
U7107 SPEED PACK - M3x16 Button Hd (pk10)
U7109 SPEED PACK - M3x25 Button Hd (pk10)
U7113 SPEED PACK - M3x10 Cap Hd (pk10)
U7122 SPEED PACK - M3x12 Csk Hd (pk10)
U7125 SPEED PACK - M3x25 Csk Hd (pk10)
U7689 M3 Brass Inserts - pk10
U7709 M3 Black Alloy Washers 0.75mm (pk10)
U7710 M3 Black Alloy Washers 1.00mm (pk10)
U7711 M3 Black Alloy Washers 2.00mm (pk10)
U7712 M3 Black Alloy Washers 3.00mm (pk10)
U7743 M2.5 X 8 Button Screws (pk10)
U7884 M3x6 Grub Screw Dome End (pk4)
U8089 M3 Alloy Washer Black 4.0 mm (pk10)
U8132 M4 X 18 CSK (pk10)
U8133 6 x 1 'O'ring (pk10)
Option Parts
AM648068 Super Diff Gear 48P 68T
AM648072 Super Diff Gear 48P 72T
AM648074 Super Diff Gear 48P 74T
AM648076 Super Diff Gear 48P 76T
AM648080 Super Diff Gear 48P 80T
AM648084 Super Diff Gear 48P 84T
AM664070 Super Diff Gear 64P 70T
AM664074 Super Diff Gear 64P 74T
AM664078 Super Diff Gear 64P 78T
AM664080 Super Diff Gear 64P 80T
AM664082 Super Diff Gear 64P 82T
AM664086 Super Diff Gear 64P 86T
AM664090 Super Diff Gear 64P 90T
AM664094 Super Diff Gear 64P 94T
AM664098 Super Diff Gear 64P 98T
AM664102 Super Diff Gear 64P 102T
AM664106 Super Diff Gear 64P 106T
AM664110 Super Diff Gear 64P 110T
AX009 Aerox Alloy Servo Arm - Short 25T Futaba
AX010 Aerox Alloy Servo Arm - Short 23T KO/Sanwa
CR024 CORE RC - Serrated M4 Steel Wheel Nut pk4
CR035 CORE RC - Serrated Alloy M4 Nuts; Blue pk 4
CR036 CORE RC - Serrated Alloy M4 Nuts; Violet pk 4
CR192 Alloy Servo Arm 25T - Futaba Short
CR193 Alloy Servo Arm 23T - KO/Sanwa Short
CR196 CORE RC - Serrated Alloy M4 Nuts - Black - pk4
CR280 Ti Pro Ball Studs - Short - (pr)
CR304 Titanium Wheel Nuts M4 - pk4
CR310 Alloy Csk Hex Screws M3 x 6 pk10
CR311 Alloy Csk Hex Screws M3 x 8 pk10
CR312 Alloy Csk Hex Screws M3 x 10 pk10
CR313 Alloy Csk Hex Screws M3 x 12 pk10
CR314 Alloy Button Head Hex Screws M3 x 6 pk10
CR315 Alloy Button Head Hex Screws M3 x 8 pk10
CR316 Alloy Button Head Hex Screws M3 x 10 pk10
CR317 Alloy Button Head Hex Screws M3 x 12 pk10
CR320 Titanium Csk Hex Screws M3 x 6 pk10
CR321 Titanium Csk Hex Screws M3 x 8 pk10
CR322 Titanium Csk Hex Screws M3 x 10 pk10
CR323 Titanium Csk Hex Screws M3 x 12 pk10
Option Parts Cont....
CR327 Titanium Button Head Hex Screws M3 x 6 pk10
CR328 Titanium Button Head Hex Screws M3 x 8 pk10
CR329 Titanium Button Head Hex Screws M3 x 10 pk10
CR330 Titanium Button Head Hex Screws M3 x 12 pk10
CR507 Kimbrough - Spur Gear 94T - 64DP - #229
CR508 Kimbrough - Precision Gear 64T-48DP-#300
CR510 Kimbrough - Spur Gear 66T - 48DP - #301
CR511 Kimbrough - Spur Gear 69T - 48DP - #150
CR512 Kimbrough - Spur Gear 72T - 48DP - #143
CR513 Kimbrough - Spur Gear 78T - 64DP - #202
CR515 Kimbrough - Spur Gear 76T - 64DP - #199
CR664 Alloy Motor Spacer - 1mm - pk2
CR721 1/12 Carbon Spool Axle + Clamp
CRW48060 Diff Spur 48DP - 60T - for Diff or Spool Axle
U1954 Pro - Thrust Bearing
U2135 M4 Nyloc Wheel Nut - Purple Alloy (pk4)
U2810 M4 Nyloc Wheel Nut - Red Alloy (pk4)
U2811 M4 Nyloc Wheel Nut - Blue Alloy (pk4)
U2812 M4 Nyloc Wheel Nut - Black Alloy (pk4)
U3582 Precision Balance Pivot Set
U4328 Impact Servo Saver
U4811 "1/8"" Silicone Nitride Ball (pk12)"
U4946 Pro Ball Bearing 5 x 10 x 4 Sealed - pr
U4970 C/F Rear Axle - Eclipse
U7690 Pro Ball Bearings 1/4 x 3/8 x 1/8 Fl Shielded
U7730 Pro-Ball Bearing 4x8x3 Sealed - (pr)
U7774 M3 Alloy Washer Black 1.5 mm (pk10)
U7825 Titanium Pivot Ball 5.5mm Low (pr)
U7828 Titanium Ball Stud Low (Ultra Short) (pk4)
U7897 Alloy Pivot Spacer 1mm - Atom 2 (pr)
U7918 Alloy Pivot Mount - Atom 2
U7919 Alloy Pivot Block - Atom 2
U7943 Alloy Spacer Clip 0.5mm (pk4)
U7944 Alloy Spacer Clip 0.75mm (pk4)
U8065 M3 Alloy Thread Inserts - pk8
U8121 Alloy Ride Height Spacer 0.75mm - Icon (pr)
U8122 Alloy Ride Height Spacer 0.50mm - Icon (pr)
U8123 C/F Camber Strap -6mm Width 2deg - Icon
U8124 C/F Camber Strap 1.5deg - Icon
U8125 Alloy Hub Carriers - Icon (pr)
U8126 Mass Damper Shaft
U8127 Alloy Chassis - Icon
U8128 Mass Damper Weight 23g
U8129 Mass Damper Weight 12g
U8130 Front Spring Red Dot - Eclipse 3 (pr)
U8131 Front Spring Green Dot - Eclipse 3 (pr)
U8137 Mass Damper Set
Pinions
CR4815 Pinion Gear 48DP 15T (7075 Hard)
CR4816 Pinion Gear 48DP 16T (7075 Hard)
CR4817 Pinion Gear 48DP 17T (7075 Hard)
CR4818 Pinion Gear 48DP 18T (7075 Hard)
CR4819 Pinion Gear 48DP 19T (7075 Hard)
CR4820 Pinion Gear 48DP 20T (7075 Hard)
CR4821 Pinion Gear 48DP 21T (7075 Hard)
CR4822 Pinion Gear 48DP 22T (7075 Hard)
CR4823 Pinion Gear 48DP 23T (7075 Hard)
CR4824 Pinion Gear 48DP 24T (7075 Hard)
Page 19
Spares List 2