Schwaiger DSR 1004 CW User manual

Digital Satellite Receiver
User's Manual
DSR 1004 CW
Cryptoworks embedded
GB
D
S
I
060615_K7_KSF-200CX_Schwaiger_Sa3 3 2006-06-15 오후 7:09:17

060615_K7_KSF-200CX_Schwaiger_Sa13 13 2006-06-15 오후 7:20:04

COVER_ENG
Digital Satellite Receiver
User's Manual
Distributed by SCHWAIGER GmbH
Würzburger Str. 17
90579 Langenzenn
-Germany-
Tel Hotline [phone]
www.schwaiger.ed
[e-mail]
DSR 1004 CW
Cryptoworks embedded
GB
060615_K7_KSF-200CX_Schwaiger_Sa5 5 2006-06-15 오후 7:08:47

General Safety
Warning
Always follow these instructions to avoid the risk of injury to
yourself or damage to your equipment.
Unplug the receiver from the AC power outlet before cleaning.
Use only a damp cloth for cleaning the exterior of the receiver.
Do not use accessories or attachments not recommended by the receiver manufacturer
as they may cause problems to the equipment and will void the warranty.
Do not place the receiver on an unstable cart, stand, tripod, bracket, or table.
The receiver may fall, causing serious personal injury and damage to the receiver.
Do not block or cover the slot opening in the receiver.
These are provided for ventilation and protection from overheating.
Never place the receiver near or over a radiator or any heat source.
Do not place the receiver in an enclosure such as a cabinet without proper ventilation
Do not stack the receiver on top of or below other electronic devices.
The apparatus shall not be exposed to dripping or splashing and with no object filled with liquids,
such as vases, shall be placed on the apparatus.
Operate the receiver using only the type of power source indicated on the marking label.
Unplug the receiver power cord by gripping the power plug, not the cord.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 1 mac-4 HP LaserJet 5100 Series T

General Safety
Servicing
Route power supply cord so that are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to the cords that plugs in the convenience receptacles,
and the point where they exit from the unit.
Use an outlet that contains surge suppression or ground fault protection.
For added protection during a lightning storm, or when the receiver is left unattached
and unused for long periods of time, unplug it from the wall outlet and disconnect
the lines between the receiver and the antenna. This will provide some protection
against electrical damage caused by lightning or power line surges.
Do not attempt to service the receiver yourself, as opening or
removing covers may expose you to dangerous voltage,
and will void warranty.
Refer all servicing to authorized service personnel.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 2 mac-4 HP LaserJet 5100 Series T

DIGITAL SATELLITE RECEIVER
OWNER’S MANUAL
SIMPLE & SPEEDY
OPERATION HANDBOOK
Before operation,
Please read the entire manual thoroughly
and retain it for future reference.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 3 mac-4 HP LaserJet 5100 Series T

Channel Search
Channel List
Edit Channel List
Program Guide
System Setting
Utility (Option)
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 4 mac-4 HP LaserJet 5100 Series T

1
DIGITAL SATELLITE RECEIVER
Contents
Remote Control Unit ...........................................................................
Front Panel ..........................................................................................
Rear Panel ..........................................................................................
Connecting Your Equipment ...............................................................
Basic Operation ..................................................................................
Menu Guide ........................................................................................
Easy Installation .......................................................................................
Main Menu ............................................................................................
Channel Search .......................................................................................
Channel Search / Installation (None, DiSEqC Switch) ...........................................
Channel Search / Installation (DiSEqC 1,2) .......................................................
Channel Search / Installation (USALS) ............................................................
Channel List ...........................................................................................
Edit Channel List ......................................................................................
Program Guide ........................................................................................
System Setting ........................................................................................
Menu Language ....................................................................................
Audio Language ....................................................................................
Subtitle Language ..................................................................................
SCART Output (option) ............................................................................
Screen Type .........................................................................................
Banner Time ........................................................................................
RF Mode (option) ...................................................................................
RF Channel (option) ................................................................................
Local Time ..........................................................................................
3
5
6
7
12
16
16
18
19
19
22
25
28
29
32
33
33
34
34
34
35
35
35
36
36
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 1 mac-4 HP LaserJet 5100 Series T

2
DIGITAL SATELLITE RECEIVER
Contents
Menu Transparency ............................................................................
Change PIN Code ............................................................................
Parental Lock .................................................................................
Receiver Lock .................................................................................
Menu Lock .....................................................................................
Auto Power (option) ...........................................................................
Timer............................................................................................
Factory Reset ..................................................................................
System Information ............................................................................
Utility (option) ....................................................................................
Troubleshooting ................................................................................
Technical Specifications ...................................................................
Menu Map .........................................................................................
36
37
37
38
38
39
39
39
39
40
42
43
45
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 2 mac-4 HP LaserJet 5100 Series T

3
DIGITAL SATELLITE RECEIVER
Remote Control Unit
MUTE To enable or disable audio.
STAND BY To switch between operation and stand by mode.
NUMERIC BUTTONS To select the channel and enter the channel edit and PIN code .
PAGE DOWN To switch between TV and Radio.
PAGE UP To change picture standard.(Option)
EXIT To change screen size.
RECALL To select the sound mode.(Mono, Left, Right, Stereo)
MENU To change channel up and down.
OK To increase or decrease the volume.
UP/DOWN To select the audio language.
LEFT/RIGHT To return to the previous channel.
EPG To display the TV/Radio program guide.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 3 mac-4 HP LaserJet 5100 Series T

4
DIGITAL SATELLITE RECEIVER
Remote Control Unit
Note! 1: When inserting batteries, make sure that the polarity (+/–) is correct.
Note! 2: The design of the Remote Control Unit may be changed without any
notice in advance.
EPG To display the TV/Radio program guide.
A/LANG To select the audio language
A/LR To select the sound mode.(Mono,Left,Right,Stereo)
GREEN To see the current information Banner guide or the satellite list.
YELLOW To sort channel list.
To display the reserved list.(Option)
SUBTITLE(RED) To enable or disable subtitle or change the channel list mode.
INFO(BLUE) To display the information box on the screen.
TV/STB To switch between TV and STB receive mode.
P.SIZE To change screen size.
P.STD To change picture standard.(Option)
TEXT To see the teletext by OSD.(Option)
TV/RADIO To switch between TV and Radio.
SLEEP To select a present time interval for automatic shut off
FAV. To change/view Favorite channel list.(Option)
PAUSE To pause or play video.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 4 mac-4 HP LaserJet 5100 Series T

5
DIGITAL SATELLITE RECEIVER
Front Panel
1.POWER(STAND BY) Switch the receiver power “ON” or “OFF”.
2.CH Up/Down : Channel Up/Down or select item of sub-menu.
3.SEG. DISP.: 4-digit 7-segment display channel information.
4.Smartcard Slot(Option): 1 shot for smartcard.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 5 mac-4 HP LaserJet 5100 Series T

6
DIGITAL SATELLITE RECEIVER
Rear Panel
1. SCART FOR TV Connect this port to the TV via SCART cable.
2. VIDEO Video connection port to the TV or other equipment.
3. 0/12V To connect 12V to an external 0/12V switch.
4. AUDIO Audio Audio connection port to the TV or other equipment.
5. RF LOOP IN To connect to a general aerial antenna and cable jacks to a
RF input jack on the STB.
6. TV OUT To connect a TV via a coaxial cable.
7. RS-232 To connect to a personal computer for software upgrade.
8. LNB To connect to a satellite antenna and cable jacks.
9. LOOP THROUGH To connect other satellite receiver.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 6 mac-4 HP LaserJet 5100 Series T

7
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
There are several ways of connecting the STB to your TV, VCR and/or Hi-Fi SYSTEM. Consult your local
supplier for assistance in setting-up your system that is best suited to your requirements.
1. Connect STB to a TV set
Connect your STB to a TV set with SCART, if your TV set is equipped for it.
Alternatively you can use A/V, TV out (UHF) or S/Video jacks.
2. Connect STB to a VCR
Connect the SCART jack from the VCR to the back of your STB.
Alternatively you can use A/V, TV out (UHF) or S/Video jacks.
How to connect your STB to various systems
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 7 mac-4 HP LaserJet 5100 Series T

8
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
3. Connect STB to a Digital Audio System
If you have a DAC with S/PDIF coaxial cable input, you can connect the STB with it to enjoy
higher quality sound. Connect S/PDIF coaxial cable to a digital amplifier.
4. Loop Through
If you have another analogue or digital STB and you wish to use the same LNB then you can
connect it via the loop through. Connect one end of the coaxial cable to the Loop Through on the
STB and connect the other end to the LNB IN on your second STB.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 8 mac-4 HP LaserJet 5100 Series T

9
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
1. Connect one end of RCA/Cinch cable to
the RCA/Cinch jack on the back of the STB
and the other end to a RCA/Cinch jack on
your TV.
If your TV doesn’t have a RCA/Cinch jack,
connect one end of RF cable to the TV OUT
on the back of the STB and the other end to
a RF input jack on your TV.
2. Connect one end of RF cable to the ANT IN
on the back of the STB and the other end to a
terrestrial antenna connection or the jack for
the public antenna on the wall.
3. Finally connect the coaxial cable from the LNB to the LNB IN jack on back of the STB.
1. Connect one end of RCA/Cinch cable to the
RCA/Cinch jack on the back of the STB and
the other end to a RCA/Cinch jack on your TV.
If your TV doesn’t have a RCA/Cinch jack,
connect one end of RF cable to the TV OUT
on the back of the STB and the other end to a
RF input jack on your TV.
2. Connect one end of your coaxial cable to
the LNB IN connector on the STB and
the other end to the REC or Receiver
connector on the DiSEqC 1.2 motor.
3. Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.
(To RCA/Cinch on your TV)
(To RCA/Cinch on your TV)
(If your TV doesn’t have RCA/ Cinch Jack)
(If your TV doesn’t RCA / Cinch Jack)
TV with Terrestrial Antenna
TV with Motorized System (DiSEqC 1.2)
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 9 mac-4 HP LaserJet 5100 Series T

10
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
1. DiSEqC 1.0 Connection
All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.
This allows multiple antennas to be connected to the STB at the same time.
If you have two or more fixed antennas or LNBs then we recommend you use a DiSEqC 1.0 switch.
Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch.
Do the same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,
connect the other end to the LNB IN socket on the STB.
2. DiSEqC 1.2/ USALS Connection
To the digital receiver, you can connect either a single satellite antenna directly or LNB of multi-feed
equipment.
When installing the USALS please consult and receive assistance from an installation specialist,
or ensure that the 0-degree angle of the motor is facing due south when installing,
for proper operation.
Reference
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 10 mac-4 HP LaserJet 5100 Series T

11
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
KEY & DISPLAY The message of the 7-segment LED (Light-Emitting Diode) on the STB
and keys are explained as below.
Standby Mode Current Program Number on TV List
System Booting Current Program Number on Radio Location
Power Off TV Mode
MICOM Version STB Mode
Upgrade
Boot Loader Version
Upgrade Procedure
Download
Upgrade Complete
Down Load Procedure
Front Panel Display Message
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 11 mac-4 HP LaserJet 5100 Series T

12
DIGITAL SATELLITE RECEIVER
Basic Operation
1. Program Information
After the television channels have been programmed, you will
see the information box each time you change the channels.
1. Every time you change channels you will receive program information for a
few seconds. (In the “Banner Time” menu you can select how long this
information will be shown.)
2. You may change channel lists with the UP or DOWN button.
You can get “Channel Banner” on the bottom of the screen.
3. When you press the COLOR button, you can use banner as a simple channel
operation. In this case, you can get a simple EPG on right view.
2. Favorite Banner
1. During “Channel Banner” is appearing, when you press SUB-T(RED)
Button, you can get “Favorite Banner” and “Lock Banner”.
2. If you already made your favorite channel in “Channel Control” menu,
you can get favorite channel on this view.
3. The banner will disappeared automatically after banner-time out.
3. Now-Information Banner
1. During “Channel Banner” is appearing, when you press GREEN
Button, you can get “Now-Information Banner”.
2. Using “Now-Information Banner”, you can get a simple EPG of
“Now-Information”.
Basic Function
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 12 mac-4 HP LaserJet 5100 Series T

13
DIGITAL SATELLITE RECEIVER
Basic Operation
4. Next-Information Banner
1. During “Channel Banner” is appearing, when you press YELLOW Button,
you can get “Next-Information Banner”
2. Using “Next-Information Banner”, you can get a simple EPG of
“Next-Information”.
5. Channel-Information Banner
1. During “Channel Banner” is appearing, when you press INFO(BLUE) Button,
you can get “Channel-Information Banner”.
2. Using “Channel-Information Banner”, you can get a detailed channel listing
information.
6. Volume Control/Mute
1. To control audio volume, press Volume / Volume buttons.
2. Volume control bar will be appeared in bottom of the TV screen
3. After time-out in 1 second, volume control bar will disappear.
To temporarily stop the volume, press the MUTE button.
To cancel mute, press the MUTE button again or press
the Volume / Volume buttons.
Basic Function
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 13 mac-4 HP LaserJet 5100 Series T