Schwinn 126 Upright Bike User manual

Do not print this page

©2006. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr., Vancouver, WA 98683

UPRIGHT BIKE
ASSEMBLY GUIDE
ASSEMBLY GUIDE
PN 001-6894 REV C (031308)

1
CONTENTS
Table of Contents
Hardware ................................................................................................2
Exploded View ........................................................................................ 3
Parts List .................................................................................................4
Assembly Instructions ..........................................................................5
Important Contact Numbers ...............................................................17

HARDWARE
2






















--
!LLEN+EY
3CREWDRIVER0EDAL7RENCH
3OCKET7RENCH
/3CREWS-X0XMM
/-X0XMM
/2EGULAR7ASHER /LOCKNUTFOR
-
/
/
/2EGULAR7ASHER
/#ARRIAGE"OLT-X0X--
/
Note: Please verify you have all correct parts and quantities before
assembling unit.
If you are missing items, are short quantities, or have damaged
components, please contact Schwinn at 1.800.864.1270

3
EXPLODED VIEW
+,
+2
/
%
$
&
'
'
#
#
"
/
! !
/
/
/
/
&
&
&
!
"
#
#
#
/
/
0
/
'
EXPLODED VIEW

PARTS LIST
4
PARTS LIST
Ref. Description Qty
A Computer 1
A-1 Screw M5x14L 4
A-2 Computer bracket 1
B Handlebar 1
B-4 Heartrate wire 1
C Handlebar mast 1
C-1 Upper computer wire 1
C-2 Bottle cage 1
C-3 Screw M5x20L 2
C-4 Bottle cage holder 1
D Front stabilizer 1
E Rear stabilizer 1
F-1 Washer 8x19x2 4
F-3 Lower computer wire 1
F-4 Screw M8xP1.25x16L 4
F-7 Seat post pop pin 1
G Seat post 1
G-1 Seat slider 1
G-8 Seat 1
K Pedal pair 1
O Angle Adjust knob 1
O-1 Screw M8xP1.25x85L 1
O-2 Nylon nut 1
O-3 Flat washer 8x16x1 2
O-4 Screw M8x16 4
O-5 Console slider adjust knob 1
O-6 Flat washer 12.5x20x2t 1
O-7 Carriage bolt M8xP1.25x80L 1
0-8 “T” Nut 1
P AC Adaptor 1

5
ASSEMBLY INSTRUCTIONS
Basic Assembly Principles
Here are a few basic tips that will aid in the assembly process .
By using these principles, you can simplify each process and save
yourself extra time and effort.
1. To make the assembly process go faster, gather the pieces you need
for each step and thoroughly read the assembly instructions for that
step prior to starting assembly for the step.
2. When attaching two pieces, gently lift and look through the bolt holes
to help guide the bolt through the holes.
3. As a general rule, and for all bolts and nuts, turn bolts or nuts toward
the right to tighten and left to loosen. Or you can remember the
mnemonic: “Righty tighty, lefty loosey.”

ASSEMBLY INSTRUCTIONS
6
Step 1 Install Front and Rear Stabilizers
Parts:
• Front Stabilizer (Ref. D )
• Rear Stabilizer (Ref. E )
Tools:
• Supplied Allen Wrench
1-1 Attach the Rear Stabilizer (E) to the rear of the Main Unit using
two M8 X 16mm screws (O-4).
1-2 Attach the Front Stabilizer (D) with the UP sticker and wheels
toward the front of the Main Unit using two M8 X 16mm screws.
D
E
O-4
UP
sticker

7
ASSEMBLY INSTRUCTIONS
Step 2 Install Pedals
Parts:
• Right Pedal (K-R)
• Right Pedal (K-L)
Tools:
• Supplied Pedal Wrench
2-1 Screw the Left Pedal ( has an “L” stamped into the end of
the pedal ) into the Left Crank Arm.
Note: The Left Pedal has a left handed thread and screws in
counter clockwise.
2-2 Screw the Right Pedal ( has an “R “stamped into the end of the
pedal ) into the Right Crank Arm.
K-R
K-L