SCIBORG HV-200 User manual

BACKING ALERT with AUTO SPEED LOCK
This product functions with select TOYOTA vehicles only. See Compatibility chart below.
Visit our website for the absolute latest information on vehicle compatibility.
Thank you for purchasing the HV-200 Backing Alert System. Please read this manual in
its entirety before using the product. Be sure to store this manual in a safe place, as you
may need to reference it in the future.
MODEL FRAME NO. YEAR
SAI (1)
AQUA / Prius C
VOXY (HV)
Esquire (HV)
Camry (1)
Corolla AXIO (HV)
Corolla FIELDER (HV)
NOAH (HV)
Harrier (HV) (1)
Prius & PHV
Priusα / Prius v / Prius+
AZK10
NHP10
ZWR80G
ZWR80G
AVV50
NKE165
NKE165G
ZWR80G
AVU65W
ZVW30#
ZVW4#W
2009(DEC.) & newer
(1) This vehicle comes with a factory-
installed Auto Speed Lock function.
NOTE: Cars newer than the above that
have been altered by the car maker may
be incompatible.
NOTE: Cars built outside Japan have
not been confirmed by us and could be
incompatible.
Latest Version Chart
2011(DEC.) & newer
2014(JAN.) & newer
2014(OCT.) & newer
2011(SEP.) & newer
2012(MAY.) & newer
2012(MAY.) & newer
2014(JAN.) & newer
2013(DEC.) & newer
2009(MAY.) & newer
2011(MAY.) & newer
WARNING!
This product is not waterproof or dust-proof. Never install in the engine compartment.
Never install where water can pool or where oil, dirt and grime could enter and cause an
electrical short.
PRODUCT WARRANTY CLAIM
HV-200TOYOTA Backing Alert System
1 YEAR (validated only by dealer and/or dated proof of purchase)
Year: , Month: , Day:
Name:
Address:
Phone: Email:
Name:
Address:
Phone: Website:
Approval Stamp
Manufacturer:
Contact TEL:
KIRAMEK, Inc.
9-183-1 Itayama-cho,
Handa-shi, Aichi-Ken 475-0936 JAPAN
[phone] ( )
Operating Hours (ex. Sat./Sun./Holidays):
10:00AM ~ NOON, 1:00PM ~ 4:00PM
PRODUCT DESC.:
Warranty Period:
Date of Purchase*:
Customer Info.*:
* Please fill in these marked sections above completely.
NOTE: Warranty Claims not accepted without valid
Approval Stamp and/or dated proof of purchase.
Seller Info.*:
MODEL:
Operational Voltage
Absolute Max./Min. Voltages
Current Consumption
Oper. Ambient Temp. Range (no condensation)
+12Vdc
<4.5mA (while CAN sleeping)
PRODUCT SPECIFICATIONSTOYOTA COMPATIBILITY
HV-200 USER GUIDE
®
Ver. 02032016
PRECAUTIONS
PLEASE READ THOROUGHLY BEFORE USE
The included wire harness and connectors are specially made for the HV-200 only. Please do not splice off the CAN or POWER wires, and do not use this
harness or connector with any other device; otherwise, a short, fire, or vehicle breakdown may occur.
WARNING
NOTE Product or vehicle failure could result from ignoring the following:
•This product is primarily intended for use on Japanese vehicles within Japan.
•Modifying this product voids the warranty and could cause harm to your car or yourself.
•Never mount this product to vehicles other than shown in our Compatibility Chart. Japanese vehicles made outside Japan may be incompatible.
•NEVER store or mount this product where water, oil, dirt, or moisture collects, or where there is intense heat or steam present as such may cause
product failure. This product is not dust-proof, waterproof or splash-proof.
• Our company shall not be held liable for traffic accidents that occur with or without the presence of this product.
•Specifications of this product are subject to change without notice.
•ALWAYS confirm that your installer has appropriate expertise and equipment to safely and properly install this product.
•We have confirmed this product functions correctly when used with other DIGI-LINK products, but we cannot guarantee compatibility when used with
third party OBD CAN-BUS devices. Such devices may malfunction or may cause malfunction in the HV-200, or may even cause a vehicle warning light to
come on.
•ALWAYS secure the product and wiring in a professional manner such that nothing loose could be caught or smashed by something in the car, become
lodged behind the foot pedals, or could cause an electrical short or fire or bodily harm.
MAIN FEATURES
•Detects Ignition state and Gear Position. An alert will sound when in Reverse Gear (unless disabled by DIP switch).
•Backing Alert can be Enabled and Disabled by DIP Switch. The default DIP Switch setting is ENABLED.
•Two types of BEEPS can by chosen for the Backing Alert via DIP Switch (Long or Short).
•When Enabled, doors automatically LOCK when the vehicle speed increases beyond 20km/h (approximately).
•Auto Speed-Locking can be Enabled and Disabled by DIP Switch. The default setting is ENABLED.
•The UNLOCK trigger (for Auto Speed-Lock) can be set by DIP Switch. The default setting LOCKs when you return the gear to the “P” position.
•Rapid deceleration (hard braking) will trigger the Emergency UNLOCK feature. Doors Unlock 9 seconds after you brake hard, when travelling 20km/h or
faster. (This is not guaranteed in a traffic accident where all electrical power is lost.)

WARRANTY TERMS
1) Warranty period is measured as one (1) year from date of purchase.
2) In the unlikely event of product failure during normal use (as defined by this manual), the product will be repaired
or replaced free of charge, but only at the original dealer/place of purchase. Demand for onsite repairs may be met in
some cases within Japan, but onsite service fees will apply and vary by location.
3) All warranty claims must be submitted through the vendor from whom you originally purchased this product. You
must fill out the form on the front page of this manual, and submit the dated purchase receipt.
4) You can only submit warranty claims to us if you have moved and can no longer visit your HV-200 dealer.
5) Customer bears the cost of removal/reinstallation fees, as well as return shipping if not hand-delivered.
6) Regardless of being covered under Warranty, the following cases resulting in malfunction will require a fee:
•Oil, water, dust, etc. having accumulated inside and on the electronics.
•Improper installation or carelessness by the user.
•Unauthorized product repair or modification.
•Accidental drops, falls or other strong impact.
•Fire, earthquake, flood, lightening, tornadoes, other natural disasters, as well as pollution, salt-air damage, etc.
•When used outside the intended use, as specified in this manual.
•Car accidents, vandalism or theft.
• Problems due to deficiencies in this manual, or if you do something this manual doesn’t specifically prohibit.
•And cases where you do not properly fill out your claim, provide false info., and/or lack a dated receipt.
7) This warranty is only valid for HV-200 users outside Japan with express written approval from KIRAMEK.
8) We cannot reissue printed documents free of charge. Please keep this document safe and do not lose it.
Product repair or replacement is guaranteed under the terms, conditions and duration of this warranty. This warranty
does not limit your legal rights. If you have questions or problems after this one (1) year warranty has expired, please
consult with the original dealer from whom you purchased the HV-200 product.
Because your warranty claim will be invalidated by an improperly filled out PRODUCT WARRANTY CLAIM card,
please carefully confirm all entries and/or consult with your HV-200 dealer before submission.
PLEASE NOTE:
DIP Switch #6 must be used as shown below to enable the HV-200 to function on
the chosen car. (DIP Switches #1 ~ #5 should have been set for your car in Step-1.)
NOTE: When the above steps are finished, you never need to do them again for
the same car, even if you disconnect the OBD plug, change your car’s battery, etc.
But if you move the HV-200 to a different compatible car, you need to repeat the
above 3 steps.
1
ON
2 3 4 5 6
Turn on the Ignition.
Flip DIP SW #6 to ON.
6
Flip DIP SW #6 to OFF.
6
FINAL SETUP
3
OBD plug: choosing which side wires exit
Connect to the car’s OBD as shown above.
You can choose which
side the wires exit.
HV-200 WIRE HARNESS
OBD PIN-OUTS
Color Description
+12V
GND
CAN-HI
CAN-LO
RED
BLK
BRN
BRN/RED
pin16pin14
CAN-LO +12V
GROUND CAN-HI
pin6pin4
OBD CONNECTION
2
9
1
9
1
If you already used the
included wire-tie, you will
need to remove it so you
can slide off the OBD cap. NOTE: When finished, secure
the wires to the tab on the
cap using a small wire-tie.
Slide off the
cap as shown.
Pull wires to the opposite
side and put cap on
as shown.
9
1
NOTE: If the vehicle’s OBD plug is already being used or if there is no space to
attach the HV-200’s OBD plug, you can either purchase our optional OB-23
splitter cable, or you can purchase our Posi-Tap connector 4-pack (p/n
NT-4.) We don’t recommend soldered connections. You would be surprised
to know how many badly soldered connections result in problems!
4-STEP INSTALLATION
Connect the HV-200’s OBD2 plug to the car’s OBD2 plug.
2
Set HV-300 features to your liking via DIP switches.
Use DIP SW#6 to confirm CAN signal compatibility.
Refer to “DIP SWITCH SETUP” below.
Refer to “OBD CONNECTION” below.
Refer to “FINAL SETUP” below.
1
3
Mount the Control Module out of view.
Refer to “MOUNTING THE CONTROLLER” below.
4
HV-200 INCLUDED PARTS
Controller
OBD
Harness
Harness Length: 1 meter
NOTE: The RED & WHT 2-pin connectors, as well as the connector on the back side near the
DIP switch block, are not used. Please do not connect anything to them.
DIP SWITCHES
The location of the DIP switches is shown in the
diagram at right.
All switches are set to OFF (all UP) by default,
as shown:
DIP SWITCH SETUP
1
1
ON
2 3 4 5 6
SW4
SW3
SW2
SW1
DIP
SW No. FUNCTION
No function. Do not touch. Leave set to OFF state.
Backing Alert Beep Length
Backing Alert Function
Speed-Lock Function
UNLOCK Trigger
One-time use only switch. See “FINAL SETUP” below.
SW5
SW6
OFF = Short Beep
ON = Long Beep
OFF = Enabled
ON = Disabled
OFF = Enabled
ON = Disabled
OFF = “P” Gear
ON = Ignition OFF
Once you have completed the first 3 Steps correctly, you simply
need to hide the HV-200 controller away from view and mount it
so it does not interfere with the foot pedals or the car’s moving parts.
MOUNTING THE CONTROLLER
4
Driver’s Kick Panel
Area above driver’s kick panel
WARNING! This product is not waterproof or dust-proof. Never install in the engine
compartment. Never install where water can pool or where oil, dirt and grime could
enter and cause an electrical short.
Location shown at left
is simply one recom-
mended location. Use
wire-ties to mount
controller. Never
obstruct foot pedals or
other vehicle parts
related to safety!