SciCan HYDRIM C51wd User manual

www.scican.com
•Operator’sManual
•Mode d'emploi
•Bedienerhandbuch
•Manuale dell'operatore
•Manual del operador
HYDR IM C51wd Operator’s Manual 95-109723 Rev. 2.0
HYDR
IM C51wd Mode d'emploi 95-109723 Rev. 2.0
HYDR
IM C51wd Bedienerhandbuch 95-109723 Rev. 2.0
HYDR IM C51wd Manuale dell'operatore 95-109723 Rev.2.0
HYDR
IM C51wd Manual del operador 95-109723 Rev. 2.0
HYDRIM®C51wd

HYDR IM C51wd Operator’s Manual
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . 1
2. Important Information . . . . . . . . . . . . . 2
3. Disclaimers . . . . . . . . . . . . . . . . . . . . . . 3
4. Installation Instructions . . . . . . . . . . . . 4
5. Instructions for Use . . . . . . . . . . . . . . . 6
5.1 Instrument Reprocessing
Recommendations . . . . . . . . . . . . . . . . . . 6
5.2 Cycle Description Chart. . . . . . . . . . . . . . 7
5.3 Baskets and Accessories. . . . . . . . . . . . . 8
5.4 Activating the Hydrim C51wd. . . . . . . . . . 9
5.5 Interrupting / Aborting a Cycle. . . . . . . . 10
5.6 Overview of the Hydrim C51wd Menus. . . 11
5.7 User Menu . . . . . . . . . . . . . . . . . . . . . . . 12
5.8 Technician Menu . . . . . . . . . . . . . . . . . . 13
5.9 Setup Menu . . . . . . . . . . . . . . . . . . . . . . 14
5.10 Opening the Door in
Case of Power Failure . . . . . . . . . . . . . . 19
5.11 Printer / USB Setup . . . . . . . . . . . . . . . . 19
6. Care and Maintenance . . . . . . . . . . . 20
6.1 Replacing the HIP Cleaning Solution . . 20
6.2 Refilling the Water Softener
Salt Reservoir . . . . . . . . . . . . . . . . . . . . . . 21
6.3 Changing the Air Filter. . . . . . . . . . . . . . 21
6.4 Cleaning the Hydrim C51wd . . . . . . . . . 22
6.5 Filter and Wash Arm Maintenance . . . . 22
7. Troubleshooting. . . . . . . . . . . . . . . . . 23
8. Material Safety Data Sheet . . . . . . . . 25
9. Warranty. . . . . . . . . . . . . . . . . . . . . . . 28
10. Specifications . . . . . . . . . . . . . . . . . 29
Manufactured by:
SciCan
1440 Don Mills Road,
Toronto ON M3B 3P9
CANADA
Phone: [phone]
Fax: [phone]
Toll free: 1-800-667-7733
For all service and repair inquiries:
Canada: 1-800-870-7777
EU: [phone]
International: 1-416-445-1600
United States: 1-800-572-1211
Email: techser[email protected]
HYDRIM and STATIM are registered trademarks of SciCan Ltd.
SysTM is a trademarkof SciCan Ltd.
All other trademarks referred to in this manual are the property of their respective owners.
0123

HYDR IM C51wd Mode d'emploi
Table des matières
1. Introduction . . . . . . . . . . . . . . . . . . . 30
2. Informations importantes . . . . . . . . 31
3. Clauses de non responsabilité . . . . 32
4. Instructions d'installation. . . . . . . . . 33
5. Notice d’emploi . . . . . . . . . . . . . . . . 35
5.1 Retraitement de l'appareil
Recommandations . . . . . . . . . . . . . . . . . 35
5.2 Descriptif du cycle . . . . . . . . . . . . . . . . . 36
5.3 Paniers et accessoires. . . . . . . . . . . . . . 37
5.4 Activation du Hydrim C51wd . . . . . . . . . 38
5.5 Interruption / Arrêt d'un cycle. . . . . . . . . 39
5.6 Aperçu des menus du Hydrim C51wd . . . 40
5.7 Menu utilisateur . . . . . . . . . . . . . . . . . . . 41
5.8 Menu technicien. . . . . . . . . . . . . . . . . . . 42
5.9 Menu Configuration . . . . . . . . . . . . . . . . 43
5.10 Ouverture de la porte en cas de panne
d'alimentation . . . . . . . . . . . . . . . . . . . . . 48
5.11 Configuration Imprimante / USB . . . . . . 48
6. Entretien . . . . . . . . . . . . . . . . . . . . . 49
6.1 Remplacement de la solution
nettoyante HIP . . . . . . . . . . . . . . . . . . . . 49
6.2 Remplissage de réservoir de sel
adoucisseur d'eau . . . . . . . . . . . . . . . . . 50
6.3 Changement du filtre à air. . . . . . . . . . . 50
6.4 Nettoyage du Hydrim C51wd. . . . . . . . . 51
6.5 Entretien du filtre et du bras de
nettoyage . . . . . . . . . . . . . . . . . . . . . . . . 51
7. Dépannage . . . . . . . . . . . . . . . . . . . . 52
8. Fiche technique du matériel
de sécurité . . . . . . . . . . . . . . . . . . . . 54
9. Garantie . . . . . . . . . . . . . . . . . . . . . . 57
10. Caractéristiques . . . . . . . . . . . . . . . 58
Fabriqué par :
SciCan
1440 Don Mills Road,
Toronto ON M3B 3P9
CANADA
Téléphone : [phone]
Fax : [phone]
Appel gratuit : 1-800-667-7733
Pour les services d'entretien et de réparation :
Canada : 1-800-870-7777
UE : [phone]
International : 1-416-445-1600
Etats-Unis 1-800-572-1211
Email : techser[email protected]
HYDRIM et STATIM sont des marques déposées de SciCan Ltd
SysTM est une marque déposée de SciCan Ltd.
Toutes les autres marques déposées mentionnées dans ce manuel sont la
propriété de leurs propriétaires respectifs.
0123

HYDR IM C51wd Bedienerhandbuch
Inhaltsverzeichnis
1. Einführung . . . . . . . . . . . . . . . . . . . . 59
2. Wichtige Information . . . . . . . . . . . . 60
3. Haftungsausschlüsse . . . . . . . . . . . 61
4. Installationsanweisungen. . . . . . . . . 62
5. Gebrauchsanweisung . . . . . . . . . . . 64
5.1 Empfehlungen zur Aufbereitung der
Instrumente . . . . . . . . . . . . . . . . . . . . . . 64
5.2 Zyklusdiagramm. . . . . . . . . . . . . . . . . . . 65
5.3 Körbe und Zubehör . . . . . . . . . . . . . . . . 66
5.4 Den Hydrim C51wd aktivieren . . . . . . . . 67
5.5 Zyklus unterbrechen / abbrechen . . . . . 68
5.6 Übersicht der Hydrim C51wd Menüs . . . . 69
5.7 Benutzermenü . . . . . . . . . . . . . . . . . . . . 70
5.8 Techniker-Menü . . . . . . . . . . . . . . . . . . . 71
5.9 Einstellungsmenü. . . . . . . . . . . . . . . . . . 72
5.10 Tür öffnen bei Leistungsausfall . . . . . . . 77
5.11 Drucker-/USB-Setup . . . . . . . . . . . . . . . 77
6. Pflege und Wartung . . . . . . . . . . . . 78
6.1 HIP Reinigungslösung ersetzen . . . . . . 78
6.2 Wasserenthärter Salzbehälter auffüllen. . 79
6.3 Luftfilter ersetzen . . . . . . . . . . . . . . . . . . 79
6.4 Den Hydrim C51wd reinigen . . . . . . . . . 80
6.5 Wartung der Filter und der
Wascharme . . . . . . . . . . . . . . . . . . . . . . 80
7. Fehlerbehebung. . . . . . . . . . . . . . . . 81
8. Sicherheitsdatenblatt . . . . . . . . . . . 83
9. Garantie . . . . . . . . . . . . . . . . . . . . . . 86
10. Spezifikationen . . . . . . . . . . . . . . . . 87
Hersteller:
SciCan
1440 Don Mills Road,
Toronto ON M3B 3P9
CANADA
Tel.: [phone]
Fax: [phone]
Gebührenfrei: 1-800-667-7733
Richten Sie Ihre Anfragen für Service- und
Reparaturarbeiten an folgende Adresse:
Kanada: 1-800-870-7777
EU: [phone]
International: 1-416-445-1600
Vereinigte Staaten: 1-800-572-1211
E-Mail: techser[email protected]
HYDRIM und STATIM sind eingetragene Warenzeichen von SciCan Ltd.
SysTM ist ein Warenzeichen on SciCan Ltd.
Alle anderen Warenzeichen in diesem Handbuch sind Eigentum ihrer
entsprechenden Besitzer.
0123

HYDR IM C51wd Manuale dell'operatore
Indice
1. Introduzione . . . . . . . . . . . . . . . . . . . 88
2. Informazioni importanti . . . . . . . . . . 89
3. Liberatorie . . . . . . . . . . . . . . . . . . . . . 90
4. Istruzioni d’installazione . . . . . . . . . 91
5. Istruzioni per l’uso . . . . . . . . . . . . . . 93
5.1 Trattamento degli strumenti
Consigli . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.2 Tabella di descrizione dei cicli . . . . . . . . 94
5.3 Cestini e accessori. . . . . . . . . . . . . . . . . 95
5.4 Attivazione dell'Hydrim C51wd . . . . . . . 96
5.5 Interruzione del ciclo . . . . . . . . . . . . . . . 97
5.6 panoramica dei menu dell'Hydrim
C51wd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
5.7 Menu utente . . . . . . . . . . . . . . . . . . . . . . 99
5.8 Menu del tecnico . . . . . . . . . . . . . . . . . . 99
5.9 Menudi Setup ...................101
5.10 Apertura dello sportello in caso di
interruzione della corrente. . . . . . . . . . 106
5.11 Setup stampante / USB ............106
6. Cura e manutenzione . . . . . . . . . . 107
6.1 Sostituzione della soluzione
detergente HIP . . . . . . . . . . . . . . . . . . 107
6.2 Riempimento del serbatoio
dell'anticalcare. . . . . . . . . . . . . . . . . . . . . 108
6.3 Sostituzione del filtro dell'aria . . . . . . . 108
6.4 Pulizia della Hydrim C51wd. . . . . . . . . 109
6.5 Manutenzione del filtro e dei bracci
di lavaggio . . . . . . . . . . . . . . . . . . . . . . 109
7. Ricerca e soluzione dei problemi. 110
8. Scheda informativa sulla sicurezza
dei materiali (MSDS) . . . . . . . . . . . 112
9. Garanzia . . . . . . . . . . . . . . . . . . . . . 115
10. Specifiche . . . . . . . . . . . . . . . . . . . 116
Prodotto da:
SciCan
1440 Don Mills Road,
Toronto ON M3B 3P9
CANADA
Telefono: [phone]
Fax: [phone]
Numero verde: 1-800-667-7733
Per tutte le richieste relative a
manutenzione e riparazione:
Canada: 1-800-870-7777
UE: [phone]
Internazionale: 1-416-445-1600
Stati Uniti di America: 1-800-572-1211
e-mail: techser[email protected]
HYDRIM e STATIM sono marchi di fabbrica registrati di SciCan Ltd.
SysTM è un marchio di fabbrica di SciCan Ltd.
Tutti gli altri marchi di fabbrica a cui si fa riferimento nel manuale
sono proprietà dei loro rispettivi proprietari.
0123

Manual del operador de HYDR IM C51wd
Índice
1. Introducción . . . . . . . . . . . . . . . . . . 117
2. Información importante . . . . . . . . . 118
3. Descargos . . . . . . . . . . . . . . . . . . . . 119
4. Instrucciones de instalación . . . . . 120
5. Instrucciones de uso . . . . . . . . . . . 122
5.1 Reprocesado del instrumento
Recomendaciones . . . . . . . . . . . . . . . . 122
5.2 Tabla de descripción de ciclo. . . . . . . . 123
5.3 Cestas y accesorios. . . . . . . . . . . . . . . 124
5.4 Activar el Hydrim C51wd . . . . . . . . . . . 125
5.5 Interrumpir / cancelar un ciclo . . . . . . . 126
5.6 Visión general de los menús de
Hydrim C51wd . . . . . . . . . . . . . . . . . . . . . 127
5.7 Menú de usuario . . . . . . . . . . . . . . . . . 128
5.8 Menú del técnico . . . . . . . . . . . . . . . . . 129
5.9 Menú Configurar .................130
5.10 Abrir la puerta en caso de fallo
eléctrico . . . . . . . . . . . . . . . . . . . . . . . . 135
5.11 Configurar Impresora/USB ........135
6. Cuidado y mantenimiento . . . . . . 136
6.1 Sustituir la solución de limpieza HIP . . 136
6.2 Rellenar depósito de sal
descalcificadora . . . . . . . . . . . . . . . . . . . 137
6.3 Cambiar el filtro del aire . . . . . . . . . . . 137
6.4 Limpiar el Hydrim C51wd . . . . . . . . . . 138
6.5 Mantenimiento del filtro y brazo
de lavado . . . . . . . . . . . . . . . . . . . . . . . 138
7. Resolución de problemas . . . . . . . 139
8. Hoja de especificaciones de
seguridad del material. . . . . . . . . . 141
9. Garantía . . . . . . . . . . . . . . . . . . . . . 144
10. Especificaciones . . . . . . . . . . . . . . 145
Fabricado por:
SciCan
1440 Don Mills Road,
Toronto ON M3B 3P9
CANADÁ
Teléfono: [phone]
Fax: [phone]
Llamada gratuita (EE.UU.):
1-800-667-7733
Para cualquier pregunta sobreservicio y
reparaciones:
Canadá: 1-800-870-7777
UE: [phone]
Internacional: 1-416-445-1600
Estados Unidos: 1-800-572-1211
Correo electrónico:
techser[email protected]
HYDRIM y STATIM son marcas comerciales registradas de SciCan Ltd.
SysTM es una marca comercial de SciCan Ltd.
Todas las demás marcas comerciales mencionadas en el presente manual
son propiedad de sus respectivos propietarios.
0123

Page 1 HYDR
IM C51wd Operator’s Manual
Thank you for selecting the Hydrim C51wd instrument washer-disinfector. The Hydrim
C51wd is designed in accordance with the EN15883-1 and -2, the European standards
for washer-disinfectors. The Hydrim complements the Statim and Quantim autoclaves by
quickly and hygienically preparing soiled instruments for sterilisation. To ensure years
of safe, trouble-free service, carefully review this Operator’s Manual before operating the
unit. The Hydrim C51wd is suitable only for the applications listed in this manual. Using
the Hydrim for other purposes may be dangerous. The manufacturer cannot be held
responsible for damage caused by improper use.
Operational, maintenance and replacement instructions must be followed for the product
to perform as designed. All trademarks referred to in this manual are the property of their
respective owners. Contents of this manual are subject to change without notice to reflect
changes and improvements to the Hydrim product.
The Hydrim C51wd should only be installed and serviced by a qualified contractor as it is
an Installation Category2device. Before connecting the unit, the installer should check
that the voltage and frequency of the electrical supply correspond with the details in the
installation instructions. The unit must only be plugged into a grounded outlet. Please note
that this unit is completely isolated from the electrical supply only when it is unplugged or
the circuit breaker is turned OFF. This must be done before any repair work is carried out.
The Hydrim C51wd uses HIP™ Cleaning Solution exclusively. The unit will not perform
as described if other detergents / cleaning products are used. Other detergents / cleaning
products maydamage the unit, the instruments,cause excessive foaming, and void
the warranty. Do not use solvents in this unit. Do not allow small children or unauthorised
personnel access to this unit or its controls.
1. Introduction

Page 2
HYDR IM C51wd Operator’s Manual
2. Important Information
The following symbols appear in this book.
Caution, there is a potential hazard to the operator.
This situation may lead to a mechanical failure.
This is important information.
The following symbols appear on the touchscreen:
Used to stop the cycle
Forward Arrow–used to move to the next menu
Back Arrow – used to move to the previous menu
Up Arrow–used to adjust a value up, or to move between screens in a menu
Down Arrow – used to adjust a value down, or to move between screens in a menu
Unlock – used to unlock the door
Printer – used to obtain a print out, if the Hydrim has a printer
Used to clear the error history
Info menu – allows access to User, Setup and Technician menus.
X

Do not permit any person other than authorised personnel to service, maintain or
supply parts for your Hydrim C51wd. SciCan shall not be liable for incidental, special
or consequential damages caused by any maintenance or services performed on
the Hydrim C51wd by unauthorised personnel, or for the use of equipment or parts
manufactured by a third party, including lost profits, any commercial loss, economic
loss, or loss arising from personal injury.
Never remove the covers of the unit and never insert objects through holes or
openings in the cabinetry. Doing so may damage the unit and/or pose a hazard to the
operator. If the unit is used in a manner other than that specified, the protection
provided by the equipment may be impaired. Avoid contact with eyes and mouth. Never
lean on the open door. The unit may tip forward causing injury.
Always turn the unit OFF before adding softener salt, adding solutions or performing
routine maintenance to the unit.
The owner shall not allowanypersonnel other than the trained and authorised personnel
to operate the unit. For further information or questions about the Hydrim C51wd,
contact your authorised dealer or:
Page 3 HYDR
IM C51wd Operator’s Manual
3. Disclaimers
SciCan
1440 Don Mills Road
Toronto ON M3B 3P9
CANADA
Phone: [phone]
Fax: [phone]
Toll free: 1-800-667-7733
SciCan Inc.
500 Business Center Drive
Pittsburgh, PA15205
USA
Phone: [phone]
Fax: [phone]
Toll free: 1-800-572-1211
SciCan Medtech
Alpenstrasse 16
6300 Zug, Switzerland
Tel: [phone]
Fax: [phone]
EC Representative
BHT Hygienetechnik GmbH
Messerschmittstraße 11
86368 Gersthofen, Germany
Tel [phone]
Fax [phone]
For all service and repair inquiries
EU +49- (0)821-278 93400
International 1-416- 445-1600
Canada: 1-800-870-7777
United States: 1-800-572-1211
Email: techser[email protected]

Page 4
HYDR IM C51wd Operator’s Manual
4. Installation Instructions
inlet valves
drain hose
hot water
inlet hose
cold water
inlet hose
The electrical outlet
should not be located
directly behind the unit
and should be accessible.
The powercord must be
routed away from the
backpanel and hotwater
inlet hose.
To open the wash chamber door, pull the ring
inside the chemical door.
Tools and supplies required for installation:
•Slot screwdriver • Channellocks
Ensure that HIP Cleaning Solution (instrument wash
chemical) is available. All other supplies are included with
the Hydrim unit.
Specifications:
Utility Hook-ups
Installation Configurations:
If the Hydrim is installed in a Sterilisation Center,
the manufacturer of the Sterilisation Center should
allow a 75 mm space at the top, back and both
sides of the Hydrim. This will facilitate installation,
levelling, and service access to the Hydrim.
The cabinetry will need to be vented and allow the
air exhaust from the dryer to escape. At least 75mm
of space should be provided behind the rear panel.
Do not move the Hydrim into place by maneuvering
the open wash chamber door. This may cause to
door to become misaligned and leak.
*unit will function with water pressure down to 0.5 bar.
Option 1. Cabinet / Sterilisation Center
Option 2. Sliding Shelf
Option 3. Counter Top
Voltage: 220 – 240 V
Frequency: 50 Hz
Rated load: 2 kW
Circuit
breaker: 10 A per phase
Height: 475 mm
Width: 600 mm
Depth: 460 mm
Depth with
door open: 780 mm
Weight: 34 kg
Running Noise: 60 dBA
Hose / Cord Length /
Diameter Max. Distance Distance from
inlet / drain
Water
Pressure
(optimal)*
Shut-off
valve
Hot inlet 1.9 m
G3/4" 1.5 m 1-10 bar Yes
Cold Inlet 1.9 m
G3/4 1.5 m 1-10 bar Yes
Drain 1.5 m
3/4" ———
Electrical 1.8 m
AWG 18-3 ———

Page 5 HYDR
IM C51wd Operator’s Manual
4. Installation Instructions
Testing water hardness and
setting the water softener (salt):
Hydrim is equipped with a built-in water softening
system which needs to be adjusted according to the
local water hardness. The Hydrim water test kit
includes three water hardness test strips in bags. Take
awater sample from the location where the machine
will be installed. Open one of the bags and remove the
test strip. Dip the strip in the water. Compare the color
of the strip with the chart on the back of the bag.
Determine the water hardness according to the chart
on the water test kit envelope. Power the unit on. Touch
the “i” in the lower right hand corner of the sceen.
Select “Setup” and then “Set Regeneration”. Using the
up and down arrows, set the water softener
regeneration
level according
to this table:
Connecting the water inlet hoses:
Connect the hot water hose (red) to the hot inlet valve on
the Hydrim (indicated by a red dot) and the cold water
hose (blue) to the cold water inlet valve on the Hydrim
(indicated by a blue dot).
The connector with the elbow should be attached to the
back of the Hydrim unit. The washer with the screen
goes to the water supply connector. Make sure that the
inlet valves are free of debris.
Drain requirements:
Connect the drain hose to the drain outlet. The drain
hose can be attached to existing drain lines using a
3.5 cm or larger standpipe / P-trap combination. If the
hose is connected directly to the drain line, fittings and
adapters should not reduce water flow. The drain hose
should be attached to the main drain at a point no more
than 1 metre above the base of the Hydrim. A floor drain
is acceptable (check local codes).
Levelling the Hydrim:
For the unit to function properly, it will need to be
correctly levelled. Tolevel the unit, follow these steps:
1. Adjust the legs underneath the unit.
2. Use the levelling bubble on the top
right hand side as a guide.
3. When the bubble is in the centre,
the unit is correctly levelled.
Installing Cleaning Solution:
Ensure that the quick-connect cap on the HIP Cleaning
Solution bottle is tight. Install the bottle and loosen the
screw-cap slightly to prevent formation of a vacuum.
Additional Information:
• The Hydrim unit is heavy (34 kg). Exercise caution when moving it.
• The Hydrim must be properly grounded.
• The Hydrim is equipped with an air gap / anti-suction device to prevent backflow of dirty water into the water supply. No
other air gap device is necessary.
• If you need to extend the water inlet and drain hoses, ensure that you use commercial grade plumbing hose. The
maximum length of the drain hose is 3.3 m.
Pour 0.5 litre of water into
the water softener by
pouring it into the salt
container and inserting it
into the chamber wall. Add
0.5 kg of water softening
salt in the same manner.
Screw the salt container
tightly into the wall of the
chamber.
Installation Test:
Turn on the shut-off valves. Run a test cycle, checking
for leaks.
water softener
container
MAX
MIN
*consider using an additional water treatment
bubble level
quick
disconnect
cap
screw cap
Hardness – ppm Hydrim setting
0 - 110 0
120 - 360 1
370 - 510 2
520 - 890* 3
>890 Additional water
treatment required

5.1 Instrument Reprocessing Recommendations
The Hydrim C51wd is designed to clean and thermally disinfect (depending on the cycle
chosen) general dental and medical instruments.
The disinfection level (A0=600) is intended to reduce the number of viable microorganisms
on a product to a level appropriate for its intended further handling or use depending on
requirements specified by regional or national authorities. Regulatory authorities may
specify more stringent requirements within the territories for which they are responsible.
SciCan recommends terminal sterilisation after processing in the Hydrim C51wd.
When used correctly, the Hydrim C51wd is effective for the removal of debris on
instruments that may result in the insulation of microorganisms during terminal sterilisation.
Prior to placing instruments in the Hydrim, consult the instrument manufacturer's
reprocessing instructions.
Examples of medical and dental instruments suitable for cleaning and disinfecting in the
Hydrim C51wd include:
•Stainless steel scalers,spatulas and hemostats.
•Stainless steel retractors,needle holders,skin hooks,tissue forceps,scissors,
curettes,and other stainless steel instruments free of deep cavities.
For best results,instruments processed in the Hydrim C51wd should have the following
properties:
•Heat resistance to a temperature of up to 84°C
•Corrosion resistance in the presence of heat and alkalinity.
Dental handpieces,microkeratomes,phaco tubing, fiberoptics and electrical equipment
should not be processed in the Hydrim.
HIPTM (Hydrim Cleaning Solution with Instrument Protection) has been carefully formulated
to provide outstanding material compatibility with a wide range of metals and coatings.
However, some manufacturers' instruments may not be compatible.
All hinged instruments should be placed in open baskets in P2 Heavy Duty cycle or P3
Heavy-Duty with Disinfection cycle.
When processing small or light objects in the Hydrim use the basket with lid (SciCan part
number 01-108294).
Page 6
HYDR IM C51wd Operator’s Manual
5. Instructions for Use

Page 7 HYDR
IM C51wd Operator’sManual
5. Instructions for Use
5.2 Cycle Description Chart
** Cycle times depend on the temperature of incoming water.
P1 – Regular
Cycle P2 – Heavy Duty Cycle P3 – Heavy Duty Cycle with Disinfection
Description Use for moderately
soiled loose
instruments
Use for heavily soiled
instruments and
cassettes
Use for heavily soiled
instruments and cassettes
Cold Prewash <45ºC <45ºC <45ºC
Wash 50ºC
5minutes
50ºC
9minutes
50ºC
9minutes
Rinse 60ºC 60ºC 80ºC for 10 minutes
Dry 0-15 min.
(10 min. default)
0-15 min.
(10 min. default)
0-15 min.
(8 min. default)
Total Time**
without drying 19 minutes 23 minutes 45 minutes
Water
Consumption 13 L 13L 13L

HYDR IM C51wd Operator’s Manual
5. Instructions for Use
6. Rack for two
baskets and
two cassettes
(optional)
Order No.:
01-109768S
3. Four cassette
rack (optional)
4. Rack for
vertical
instruments
(optional)
5. Largebasket
(optional)
Part Name Order No. Part Dimensions
Statim 2000 basket 01-107240 275 mm x 178 mm x 32 mm
(2included with Hydrim)
Statim 5000 basket 01-107241 373 mm x 178 mm x 42 mm
(Optional)
2. Basket with
hinged lid
(optional)
Order No.:
01-108294
Dimensions: 216 mm x 140 mm x 54 mm
Basket Order No.:
01-108210
Dimensions:
350 mm x 368 mm x 64 mm
Support Rack for Large Basket Order No.:
01-108214
Dimensions: 350mm x 350mm x 48mm
Order No.:
01-109153
Order No.: 15555.00
5.3 Baskets and Accessories
Observe the instrument manufacturer's recommendations for cleaning and care. When
loading the unit, arrange loose instruments so that they do not touch one another.
Instruments with concave surfaces or cavities should be placed so that water can drain freely.
1. Baskets only
Page 8

5.4 Activating the Hydrim C51wd
Prior to activating the washer-disinfector, check that the water supply is on and follow
these steps:
Page 9 HYDR
IM C51wd Operator’s Manual
5. Instructions for Use
Open the chemical door and ensure that a bottle of HIP Hydrim Cleaning Solution
has been installed.
Load instruments
into the baskets or
cassettes, place
them in the machine
and close the door.
Touch the
screen to
begin.
Select the desired cycle.
(Use a heavy duty cycle
for cassettes, hinged
instruments or heavily
soiled instruments.)
Press Start
Turn the
unit on.
MAX
MIN
connector
1
5
2
Press to unlock door.
4
6 7
21:06 31/02/07
SH23MR300
HYDRIM
3
P1 Regular
P2 Heavy Duty
P3 HD & Dis.
P1 Regular
START

Page 10
HYDR IM C51wd Operator’s Manual
5. Instructions for Use
The cycle will start by draining the unit for 20 seconds. The bar
on the screen indicates the progression of the cycle. The stage
within the cycle is shown beneath the bar (eg. Filling, Rinsing).
The estimated time remaining (in minutes) is always displayed.
Please note that the time will increase or decrease depending
on the projected cycle completion.
When the cycle is complete, the program name and “Cycle
Complete” is displayed, and the unit beeps three times. Press
to open the door. Use gloves to unload the instruments. After all
cycles, exercise caution as the instruments, trolley, baskets and
cassettes may be hot. Inspect the instruments for debris prior to
packaging / sterilising.
5.5 Interrupting / Aborting a Cycle
The door of the Hydrim is locked during the cycle. If the STOP
button is pressed, the cycle is aborted and cannot be re-started.
The message “Draining. Please wait” will appear. The unit will
drain. Then the message “Instruments not processed. Cycle
Aborted” will appear. Press OK. Open the door by pressing .
Use gloves if handling the instruments. Exercise caution as
instruments, trolley, baskets and cassettes may be hot. The
cycle must be repeated to ensure that instruments are properly
processed. Note that if the drying phase of the cycle is
interrupted, the critical parts of the cycle are complete and the
message displaying the program name and “Cycle Complete.
Drying interrupted” will appear.
P1 Regular
FILLING
P1 Regular
Cycle Complete
35 min
P1 Regular
Instruments
not processed
Cycle Aborted
OK

Page 11 HYDR
IM C51wd Operator’s Manual
5. Instructions for Use
Set Drying Time
User Technician Setup
Error History Date Setup
Time Setup
Cycle Count
Reset Drying Counter
Screen Saver
Temperature C/F
Set Button Beep
Printer Selection
Baud Rate
Set Regeneration
Unit No.
Language Selection
Date/Time
Date Format
12/24 Hour
21:06 31/02/07
SH23MR300
HYDRIM
5.6 Overview of Hydrim C51wd Menus

Page 12
HYDR IM C51wd Operator’s Manual
5. Instructions for Use
5.7 User Menu
To access the user menu, follow these steps:
Turn the Hydrim OFF and then ON. An i(information) will
appear briefly at the bottom right hand of screen.
Touch the ito move to the Menu screen.
Select User.
21:06 31/02/07
SH23MR300
HYDRIM
User
Menu
Technician
Setup
The user menuconsists of
three choices.
Set Drying Time
User Menu
Error History
Cycle Count
10min
Set Drying Time
P1 Regular
Default 10min
User Menu – Set Drying Time
The drying time for P1, P2 and P3 can be set independently.
Touch the cycle for which you want to set the drying time. Use
the up and down arrows to select the desired drying time.
Touch default if you wish to return to the factory default. Use
the back arrow to return to the previous screen.

User Menu – Error History
This allows the user to see the last
three errors. Press the down arrow to
move to the next page / error. If the
Hydrim has a printer, press the printer
icon to obtain a print-out of the error
history. Press the X in the lower left
hand corner to clear the error history.
Press the back arrow to move to the
previous menu.
User Menu – Cycle Count
This allows the user to see how many
cycles have been run on the Hydrim.
Touch cycle count and the number of
cycles (completed and aborted) will be
displayed. This cannot be reset. Touch
the backarrowto return to the previous
menu.
Page 13 HYDR
IM C51wd Operator’s Manual
5. Instructions for Use
Set Drying Time
Error History
Printout 1 Page 1/2
HYDRIM C51wd
Software Rev. 3.00
Software Rev. 3.00
Software Rev. 3.00
16:32 26/01/2007
Unit No. : 00
Cycle Number: 000032
START 26 C 00:00:02
TEST 19C 00:00:43
User Menu
Error History
Cycle Count
Set Drying Time
Cycle Count
2
User Menu
Error History
Cycle Count
5.8 Technician Menu
This menuis only available to authorised technicians.
Technician

Page 14
HYDR IM C51wd Operator’s Manual
5. Instructions for Use
5.9 Setup Menu
To access the Setup Menu, proceed to the menu screen by turning the Hydrim OFF and
then ON. An i (information) will appear briefly at the bottom right hand corner.
Touch the i to move to the Menu
screen and select Setup.
The Setup Menu consists of ten
choices as shown. Using the up and
down arrows to move through the
choices, touch the desired option to
select it. For more detail on each
setup menuoption, refer to the
following sections.
21:06 31/02/07
SH23MR300
HYDRIM
User
Menu
Technician
Setup
Unit No.
Setup
Language Selection
Date/Time
Reset Dryer Counter
Setup
Screen Saver
Temperature C/F
Set Beep Button
Setup
Printer Selection
Baud Rate
Set Regeneration
Setup