Scolmore CLICKsmart RFSC-61 User manual

The unit described in these instructions are for use in a Standard UK Plug
Socket, they also feature a Standard UK Plug Socket on the front side of the
product.
On the RFSC-61 the front socket is used to remotely switch an appliance that is
plugged into it.
Supply Voltage: 230V~
Frequency: 868MHz
Signal Range (free Air): 200M
Ingress Protection: IP20
Dimensions: 60 x 120 x 80mm
Load Capacity Rated Current: 13A
Applicable Standards: EN60669, EN300 220, EN301489
1 RFSC-61 - Wireless Plug In Switching Socket
3 Programming
Plug in the Switching
Socket and turn on the
power at the mains
socket.
Press and hold the “STATUS/
PROG” button for 2 Seconds.
The red indicator will ash every
second indicating the product is in
programming mode.
1 2
Function 1 Press button Press for ON, release for OFF
Function 2 ‘On’ button Press for ON
Function 3 ‘Off’ button Press for OFF
Function 4 On/Off button Press for ON, press again for OFF
Function 5 ‘Off’ delay Press for ON, device will turn off after pre-determined time period as set in step 3 of programming
(2 secs - 60 mins max)
Function 6 ‘On’ delay Press to start timer. ‘On’ delay will be as pre-determined in step 3 of programming (2 secs -60mins)
4 Functions (Switching Receivers)
Any device with the signs of damage and/or missing parts should NOT be installed and
should be returned to the seller.
Please refer to ‘Installation Guidance Notes’ supplied before commencing with the
installation.
Devices are designed to be mounted internally only.
2 Signal Range
The RFSC-61 has a signal range in free air of up to 200 metres.
Once the signal penetrates building materials etc. the signal range will be reduced. See the installation guidance notes supplied
with this device.
Functions 5 & 6 (timed elements) are programmed in real time. If you require 40 minutes you have to wait for the 40 minutes to
complete the pairing.
For 5+ minute timed elements, we always recommend conducting a few shorter timed elements (e.g. 10 seconds) to ensure both the
correct function and the correct timed element are programmed.
www.click-smart.com
CS2 Memory: The product marked CS2 enables the receiver to remember the status (if engaged) in the event of a power cut.
Once engaged and the current status has be running for longer than 15 seconds the current status will be stored.
See Section 7 overleaf.

5 Programming The Receiver To Button Transmitters
With any of the above (RF KEY/RFWB-40G/RFWB-20G/
RFIM-40B) use the table in section 4 to program the
switching socket to function as indicated. Push the button
or switch (slowly and positively) the amount of times shown
to program the corresponding function. E.g. Function 4 will
require 4 presses.
Up to 32 transmitting devices can be paired with the
If you are using the “RF Pilot” or the
“RF Touch” (left) you can enter the
address of the switching socket. The
address of the unit can be found here.
Once you have pressed the button/
switch on the transmitter the
correct amount of times, press the
‘STATUS/PROG’ button <1 second
to complete.
Once the unit has been programmed
you can plug in your desired
appliance.
7a 7b
6a
If an error has been made during programming, a single
pairing can easily be removed.
1. Press and hold the “STATUS/PROG” button for 5
seconds. The red indicator will ash twice a second.
2. Press the transmitter button paired incorrectly. The red
indicator should stop ashing conrming the pairing is
removed.
To remove all pairings press and hold the “STATUS/
PROG” button for 10 seconds, release, then press <1
second to complete.
With RFIM-40B
When installing with the RF Pilot or RF Touch, use the dedicated product manuals for programming
Switching Socket.
If an error during programming has been made see step 6.
Functions 5 and 6 time delay options: After the initial 5 or
6 presses, hold the ‘STATUS/PROG’ button for a further 5
seconds. The red indicator will ash 2 times a second, the
timer has started. After the required time has run press the
button on the transmitter originally paired above to stop the
timer.
Then proceed to step 7.
6 Removing Pairings
6b
7 Exiting Programming
8 Programming - RF Pilot & RF Touch
Scolmore Park, Landsberg, Licheld Road Industrial Estate, Tamworth, Staffordshire B79 7XB
Tel: [phone] Fax: [phone] www.scolmore.com V2.0
CS2 - Memory Status
Single LED ash on exit - Memory status not engaged
Double LED ash on exit - Memory status is engaged
To toggle between status’s enter and exit programming mode.