Panasonic AW-PB306 User manual

Model AW- P
Before attempting to connect, operate or adjust this product, please read
these instructions completely.
Studio SDI Card
This product consists of an SD card and an interface
bracket.

2
FCC Note:
This device complies with Part 15 of the FCC Rules.
To assure continued compliance follow the attached
installation instructions and do not make any
unauthorized modifications.
This equipment has been tested and found to comply
with the limits for a class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be required to
correct the interference at his own expense.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUT ON: TO REDUCE THE R SK OF ELECTR C SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERV CEABLE PARTS NS DE.
REFER TO SERV C NG TO QUAL F ED SERV CE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (service) instructions in the
literature accompanying the appliance.
This Class A digital apparatus complies with Canadian
CES-003.
Cet appareil numérique de la class A est conforme à
la norme NMB-003 du Canada.
For CANADA
indicates safety information.
WARNING:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
E UIPMENT TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE,
USE THE RECOMMENDED ACCESSORIES
ONLY.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, REFER MOUNTING OF THE
OPTIONAL INTERFACE BOARD TO
UALIFIED SERVICE PERSONNEL.

3
Contents
Overview
nstalling the SD card in a convertible camera (such
as the AW-E300, AW-E600, AW-E800A) and
mounting the camera on the interface bracket makes
it possible for a viewfinder and/or inter-
communications headset to be used and thus enable
the camera to be used as a studio camera.
t is also possible to output SD signals which are
compliant with the SMPTE259M standard.
Features
OSD signal output compliant with SMPTE259M
standard (max. 200 m using a BELDEN 9231
coaxial cable)
OAn inter-communications headset can be used and
its volume adjusted
Oncludes viewfinder STANDBY/ON switch
OOutput signals (brightness and composite video
signals) to the viewfinder can be switched using the
menu settings
OZebra pattern and safety zone displays appearing
in the viewfinder can be switched using the menu
settings
Operating precautions
Important
OThis product consists of an SD card and an
interface bracket.
The EVF /F cable of the interface bracket must be
connected to the connector on the SD card before
use. f this connection is not performed, signals will
not be output from the SD card.
OWhen connecting or disconnecting a cable from any
unit, ensure that the power to that unit is turned off.
ODo not drop this product or subject it to strong
shock or vibration, as this may cause it to
malfunction.
OAvoid using the unit in very humid or dusty
locations, as this may cause it to malfunction.
OAvoid using the unit in locations where the
temperature is below freezing point or above 104°F
(40°C). Otherwise, the picture quality may
deteriorate or malfunctioning may result.
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Operating precautions . . . . . . . . . . . . . . . . . . . . . .3
Parts and their functions . . . . . . . . . . . . . . . . . . . .4
SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
nterface bracket . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installing the SDI card . . . . . . . . . . . . . . . . . . . . . . .5
Interface bracket mountings . . . . . . . . . . . . . . . . . .6
Mounting the bracket on a tripod . . . . . . . . . . . . . .6
Mounting the camera . . . . . . . . . . . . . . . . . . . . . . .6
Mounting the viewfinder . . . . . . . . . . . . . . . . . . . . .6
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connected components . . . . . . . . . . . . . . . . . . . . .7
Setting and changing of menu items . . . . . . . . . . .8
Performing the settings . . . . . . . . . . . . . . . . . . . . .8
Optional card settings submenu . . . . . . . . . . . . . .9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4
$SDI card $Interface bracket
1EVF I/F connector
The EVF /F cable 7from the interface bracket is
connected here.
f the EVF /F cable is not connected, signals will
not be output from the SD card.
2SDI OUT connector
SD signals are output from here.
3EVF connector
The viewfinder (such as the WV-VF65B or AW-
VF80) is connected here.
4EVF standby switch
ST.BY. :Places the viewfinder in standby mode.
ON :Outputs images to the viewfinder.
5Inter-communications level control
This adjusts the sound level output to the inter-
communications headset.
6Inter-communications jack,
plug type: 1/8˝ (3.5 mm)
The inter-communications headset is connected
here.
f the plug diameter does not match, use the
adjuster plug supplied with this product.
1/4˝ 51/8˝ (6.35 mm 53.5 mm)
7EVF I/F cable
This is connected to the EVF /F connector 1on
the SD card.
Parts and their functions
EVF I/F
SDI OUT
2
1
INCOM
ST. BY ON
LEVEL
7
3 4 6
5

MENU
OPTION CARD VIDEO OUT
G/L IN
IRIS
DC12V IN
I/F REMOTE
ITEM/AWC
YES/ABC
NO/BAR
SDI OUT
EVF I/F
MENU
OPTION CARD VIDEO OUT
G/L IN
IRIS
DC12V IN
I/F REMOTE
ITEM/AWC
YES/ABC
NO/BAR
5
Installing the SDI card
Before installing the SDI card:
ORelease the static carried in the body of the person
to perform the installation.
nstallation can be performed more safely if an anti-
static wrist strap is worn.
Touching the card without first releasing this static
may cause malfunctioning.
ODo not allow the metal part of the card come in
contact with any other metal parts.
1
Turn the power to the camera off and remove any
cables which are connected to the power
connector or other connectors.
2
Loosen the 4 screws on the rear panel of the
camera, then remove the panel itself.
3
Loosen the 2 screws on the optional card slot
cover, then remove the cover.
4
Align the SD card with the guides and insert it.
Ensure the card is fully inserted.
5
Firmly tighten the 2 screws to the optional card
slot.
f the screws are misplaced, use the extra screws
supplied with this product. (6 mm in length)
6
Firmly secure the rear panel with the 4 screws.
f the screws are misplaced, use the extra screws
supplied with this product. (8 mm in length)
Always ask your local dealer to install
the SDI card.
Rear panel
Optional card slot cover
SDI card
Screws (6 mm)
Screws (8 mm)
CAUTION:
These servicing instructions are for use by
qualified service personnel only. To reduce the
risk of fire or electric shock do not perform any
servicing other than that contained in the
operating instructions unless you are qualified
to do so.

6
Interface bracket mountings
2
Mount the camera (in which the SD card has been
installed) on the interface bracket.
Fasten the fixing knob to firmly secure the camera.
6
Connect the EVF /F cable from the interface
bracket to the EVF /F connector on the SD card.
3
Attach the mounting base (supplied with the
viewfinder) to the top section of interface bracket
using the 2 screws.
4
Slide the viewfinder onto the mounting base and
tighten the fixing knob to secure it firmly.
5
Connect the viewfinder cable to the EVF connector
on the interface bracket.
1
Mount the interface bracket on the tripod.
(Screw: 1/4 – 20 UNC)
$Mounting the camera
$
Mounting the viewfinder on a bracket $Mounting the bracket on a tripod
Fixing knob
Mounting base
Fixing knob

INCOM
ST. BY ON
LEVEL
MENU
OPTION CARD
EVF I/F
VIDEO OUT
G/L IN
IRIS
DC12V IN
I/F REMOTE
SDI OUT
ITEM/AWC
YES/ABC
NO/BAR
7
Connections
$Connected components
Convertible camera:
AW-E300, AW-E600, AW-E800A, etc.
Viewfinder:
WV-VF65B, AW-VF80, etc.
Remote control unit (RCU):
WV-RC700A, WV-RC550, etc.
Inter-communications headset
Video monitor
SDI monitor
OUse the RCU cable (AW-CA50A26) to connect the
remote control unit to the convertible camera.
Power to the camera is supplied from the remote
control unit.
Inter-communications headset
Inter-communications headset
Convertible camera:
AW-E300, AW-E600, AW-E800A, etc.
Viewfinder:
WV-VF65B, AW-VF80, etc.
Remote control unit (RCU):
WV-RC700A, WV-RC550, etc. RCU cable:
AW-CA50A26
Coaxial cable:
BELDEN 9231 (max. 200 m)
Coaxial cable
Composite signals
SDI output
Video monitor
SDI monitor

¢¢Halogen Mode Set¢¢
Brightness Set
Color Set
G/L. Color Bar Set
Sharpness Set
Other Set
Option Card Set
Initialize Data
End
8
OMain menu for halogen light mode, fluorescent light mode
and outdoor mode
OMain menu for user mode
The mode selected is displayed here.
To return to filming mode
(This is displayed when the convertible camera is used to
perform the settings.)
Camera settings to match the system configuration
and filming conditions can be made using the menu
screens.
See the convertible camera operating instructions for
more information on the settings.
PAGE TEM UP DOWN
COARSE F NE
SC PHASE
270°
180°90°
0°
H.PHASE
USER SET
OFFENC
VF ON
ORemote control unit (WV-RC700A)
OConvertible camera
MENU
OPTION CARD
EVF I/F
VIDEO OUT
G/L IN
IRIS
DC12V IN
I/F REMOTE
SDI OUT
ITEM/AWC
YES/ABC
NO/BAR
MENU button
ITEM/AWC button
YES/ABC button
NO/BAR button
DOWN button
UP buttonITEM button
PAGE button
USER SET switch
PAGE TEM
SET UP
UP DOWN
2
1
OFF
ORemote control unit (WV-RC550)
DOWN button
UP button
PAGE button
ITEM button
SET UP switch
Setting and changing of menu items
$Performing the settings
1
Display the main menu.
When performing the settings with the
convertible camera:
Press the MENU button continuously for at least
5 seconds.
When performing the settings with the remote
control unit:
OWV-RC700A:
Set the USER SET switch to “ON.”
OWV-RC550:
Set the SET UP switch to “1” or “2.”
2
Select “Option Card Set” to display the submenu.
When performing the settings with the
convertible camera:
Press the MENU or TEM/AWC button to move
the flashing to the setting item, then press the
YES/ABC button to display the submenu.
When performing the settings with the remote
control unit:
Press the PAGE or TEM button to move the
flashing to the setting item, then press the UP
button to display the submenu.
3
Select the setting item and change the setting.
When performing the settings with the
convertible camera:
Press the MENU or TEM/AWC button to move
the flashing to the desired setting item, then
press the YES/ABC or NO/BAR button to
change the setting.
When performing the settings with the remote
control unit:
Press the PAGE or TEM button to move the
flashing to the desired setting item, then press
the UP or DOWN button to change the setting.
¢¢User Mode Set¢¢
Iris, Shutter, Gain Set
Color Set
G/L. Color Bar Set
Detail Set Detail Set2
Color Matrix Set
Other Set
Option Card Set
Initialize Data
End

¢¢Option Card Set¢¢
Zebra Indicator ON
Zebra Level 70%
Zebra 2 Level 85%
Safety Zone
EVF Output Y
End
9
Setting and changing of menu items
$Optional card settings submenu
4
Return to filming mode.
When performing the settings with the
convertible camera:
Press the MENU or TEM/AWC button and
select “End” on the main menu, then press the
YES/ABC button.
When performing the settings with the remote
control unit:
OWV-RC700A:
Set the USER SET switch to “OFF.”
OWV-RC550:
Set the SET UP switch to “OFF.”
After being returned to filming mode, the
convertible camera will operate as per the changed
settings.
1
3
4
2
1Zebra Indicator
This sets the Zebra pattern display which appears
in the viewfinder.
ON :Zebra patterns are displayed in the
viewfinder.
OFF :Zebra patterns are not displayed in the
viewfinder.
<Note>
Even if ON is selected for this setting, the zebra
patterns will not be displayed in the viewfinder if
“CVBS” has been selected as the EVF Output 4
setting.
2Zebra 1 Level (70% to 109%)
Zebra 2 Level (71% to 110%)
Two types of zebra patterns are displayed to use as
a yardstick for the brightness level.
The striped zebra pattern display of Zebra 2 Level
is more dense than that of Zebra 1 Level.
<Notes>
OThese settings are available when “ON” has
been selected for the Zebra ndicator 1setting.
OThe setting for Zebra 2 Level should be set at
least 1% higher than that for Zebra 1 Level.
3Safety Zone
This selects the type of safety zone that is
displayed in the viewfinder.
f “OFF” is selected, a safety zone will not be
displayed.
<Note>
The safety zone and the center marker reflect the
electrical positions which may differ from the optical
positions.
The inner frame and the outer frame are
approximately 90% and 95%, respectively, of the
safety zone.
4EVF Output
This sets the signals to be output to the viewfinder.
Y :Brightness signals are output to the
viewfinder.
CVBS :Color signals are output to the viewfinder.
<Note>
The zebra pattern is not displayed in the viewfinder
when “CVBS” has been selected.
1 2
4
3
5

10
Specifications
Power requirements:
DC 12V (supplied from convertible camera)
Power consumption:
15.6 W
Allowable operating temperature:
32°F to 104°F (0°C to 40°C)
Allowable operating humidity:
30% to 90% (without condensation)
Dimensions (WaHaD):
SDI card
7/8˝a2 13/16˝a4 3/8˝ (21.5a70a111 mm)
Interface bracket
7 1/2˝a7 1/4˝a6 3/4˝ (190a183a171 mm)
Weight:
SDI card
0.242 lb (0.11 kg)
Interface bracket
2.112 lb (0.96 kg)
I/O connectors:
SDI card
SD OUT connector:
BNC; compliant with SMPTE259M standard
EVF /F connector:
12-pin; round
Interface bracket
EVF connector:
12-pin; round; composite signals/brightness
signals; 1.0 V [P-P]
nter-communications jack:
plug type: 1/8˝ (3.5 mm)
Switch/control functions:
Interface bracket
EVF standby switch (STANDBY/ON)
nter-communications level control
Menu screens
Zebra ndicator (ON/OFF)
Zebra 1 Level (70% to 109%)
Zebra 2 Level (71% to 110%)
Safety Zone (1/2/3/4/5/OFF)
EVF Output (Y/CVBS)
$Accessories
Adjuster plug
1/4˝ 51/8˝ (6.35 mm 53.5 mm) . . . . . . . . . . . . . . .1
Screws (6 mm in length) . . . . . . . . . . . . . . . . . . . . . .2
Screws (8 mm in length) . . . . . . . . . . . . . . . . . . . . . .4
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.

PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
D V S ON OF MATSUSH TA ELECTR C CORPORAT ON OF AMER CA
Executive Office:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 [phone]
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 [phone]
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 [phone]
Central Region:
1707 N Randall Road E1-C-1, Elgin, L 60123 [phone]
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 [phone]
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 [phone]
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) [phone]/24 Hr. Fax [phone]
Emergency after hour parts orders [phone]
TECHNICAL SUPPORT:
Emergency 24 Hour Service [phone]
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 [phone]
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
San Gabriel ndustrial Park, 65th nfantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 [phone]
F0701W1071 @
Printed in Japan
VQT9295 P