Scott Living 1274SB-23-258 Quickspecs

ASSEMBLY, CARE & USE INSTRUCTIONS
48” Fireplace Media
Console
MODEL # 1274SB-23-258; 1274SB-23-259
Français p. 15
Español p. 29
Date Purchased _______________________
www.greentouchhome.com

2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Top 1
B Center Panel 1
C Left Middle Wall 1
D Right Middle Wall 1
E Left Outer Wall 1
F Right Outer Wall 1
G Left Door 1
H Right Door 1
I Shelf 2
J Back Panel 2
K Base 1
L Front Trim 1
M Wooden Insert Bracket 2
N Insert 1
O Insert Remote Control 1
P Battery 2
Q Sound System
Remote Control
1
PAIR
EQ
A
J
G
M
M
D
I
F
H
K
L
N
P O
Q
E
C
B
J

3
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
PART DESCRIPTION QUANTITY
AA Wooden Dowel 4
BB Long Bolt 5
CC Washer 5
DD Back Panel Screw 16
EE Bolt 18
FF Shelf Pins 8
GG Touch-up Pen 1
HH Door Pull 2
II Door Pull Bolt 4
AA BB CC DD EE FF
HH II
GG

4
Hardware Used
Wooden Dowel x 4
AA
PREPARATION
ASSEMBLY INSTRUCTIONS
Estimated Assembly Time: 45 minutes
Before beginning assembly of product, make
sure all parts are present. Compare parts with
package contents list and hardware contents list.
If any part is missing or damaged, do not attempt
to assemble the product.
Tools Required for Assembly (not included):
Phillips screwdriver
2. Insert two wooden dowels (AA) into each side of
center panel (B)
B
AA
2
Hardware Used
BB
CC
Long Bolt x 3
Washer x 3
1. Place front trim (L) onto base (K), securing
with three washers (CC) and three long bolts (BB).
K
LCC
BB
1
2
1

5
ASSEMBLY INSTRUCTIONS (CONT’D)
Hardware Used
Bolt x 4
EE
4. Place assembly from step 3 onto base (K), securing
with four bolts (EE).
5. Attach right outer wall (F), securing with two
bolts (EE).
Repeat for left outer wall (E).
Hardware Used
Bolt x 4
EE
3. Align the wooden dowels in center panel (B) to left
middle wall (C) and right middle wall (D). Insert
wooden dowels into predrilled holes and press tight.
C
B
D
3
EE K
1
1
2
4
EE
E
K
F
1
1
5
2

6
ASSEMBLY INSTRUCTIONS (CONT’D)
Hardware Used
Bolt x 10
EE
6. Attach top (A), securing from underneath
with ten bolts (EE).
Hardware Used
Back Panel Screw x 16
DD
7. From behind the assembly, attach back panel (J)
to shelving areas using back panel screws (DD).
Repeat for remaining back panel (J).
8. Hold the door and align the hinge body with the
hinge plate mounted to the fireplace wall. Align
and slide the hooks/catches on the hinge body
into the recesses on the mounting plate while
lightly pushing the door towards back of
fireplace mantel. Then press on the back part
of the hinge body until you hear it click into
place.
Repeat for other hinges.
To remove press the square button at the back
of the hinge body to release the hinge from the
mounting bracket. Unlock both hinges and pull
the door away from the fireplace body.
1
J
J
DD
2
7
A
E
C
D
F
B
1
1
EE
6
2
1
8
2
3

7
ASSEMBLY INSTRUCTIONS (CONT’D)
Hardware Used
Shelf Pin x 8
FF
10. Insert shelf pins (FF) at desired height, ensuring
they are level. Place shelf (I) on top of shelf pins
(FF).
Repeat for remaining shelf (I).
Hardware Used
Door pull x 2
HH
Door pull bolt x 4
II
9. Place door pull (HH) into predrilled hole on right door,
Securing with two door pull bolt (II).
Repeat for remaining door pull (HH).
II
HH
9
2
I
2
I
10
FF
1

8
ASSEMBLY INSTRUCTIONS (CONT’D)
Note: Before proceeding to the next step, with the
help of another person, move the mantel close to
the final desired location.
12. With the help of another person, position insert (N)
into middle opening of mantel assembly.
Note: DO NOT plug insert (N) into power outlet
yet.
CAUTION: DO NOT slide insert on top of wood to
avoid scratching wood surface.
11. If you need to adjust the doors, do so in the following manner.
To adjust door up or down, loosen screws (a) on both hinges, adjust door, and retighten screws.
To adjust door left or right, turn screws (b) on both hinges, in or out.
To adjust door in or out, loosen screws (c) on both hinges, adjust door, and retighten screws.
N
12
11
2
2
2
2
2
2
1
3
1
1
1
3

NOTE: Use the pre-assembled levelers on the
base of the fireplace to level the unit. Twist the
levelers counter clockwise to increase the
height, twist the clockwise to decrease the
height.
9
13. To secure the insert by using two wooden insert
brackets, align the hole on wooden insert brackets
(M) to the hole of Left middle wall (C) and Right
middle wall (D), secure with two long bolts (BB) and
Washers (CC).
Hardware Used
BB
CC
Long Bolt x 2
Washer x 2
ASSEMBLY INSTRUCTIONS (CONT’D)
M
BB
CC
13
2
M
1
M

10
WARNING
WARNING
Adaptor Input AC100-240V, 50/60Hz
Adaptor Output DC15V 2.5A
Power Consumption 60 Watts
SOUND SYSTEM
PRODUCT SPECIFICATIONS
• Read and keep all instructions.
• To reduce the risk of electric shock do not remove cover or back panel. No user-serviceable parts
inside. Refer servicing to qualified service personnel.
• For Indoor use only. DO NOT expose this product to rain, moisture, dripping or splashing.
• DO NOT try to bypass the safety function of the polarized plug. A polarized plug has two blades with
one wider than the other. The wideblade is a safety feature. When the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
• Use this product as described in the manual only. Any other use may cause fire, electric shock, or injury.
• Refer all servicing to qualified service personnel. Servicing is required when the product has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found the comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different for that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician

11
OPTICAL LINE IN R AUX IN L DC 15V IN
OPERATING INSTRUCTIONS
BACK PANEL AND WIRING
DISPLAY
When scrolling through source options, selections will be indicated as follows:
When scrolling through EQ options, selections will be indicated as follows:
Multiple sources can be wired to the sound system using the inputs located at the back of the unit.
An optical cable is provided and we recommend using this option to wire your television to the system
for best digital sound.
To supply power to the system:
1. Connect the small end of the Power Cable into the DC Adaptor
2. Connect the DC Adaptor into the DC 15V IN input located on the back panel
3. Plug the Power Cable into a standard wall outlet.
A numerical display will illuminate on the front mesh to indicate the settings
(Volume Level, Bass Level, Treble Level, EQ and Source Selection).
OP: OPTICAL : Optical Cable Input (Included)
L1: LINE IN : 3.5 mm Audio Cable Input (Not Included)
AU: R AUX IN L: RCA Cable Input Left and Right (Not Included)
BL: Device pairing
1: EQ optimized for music
2: EQ optimized for movies
3: EQ optimized for dialogue

12
PAIR
EQ
OPERATING INSTRUCTIONS (CONT’D)
Sound System
Remote Control Control Panel
ON/OFF
PLAY/PAUSE
VOLUME UP
VOLUME DOWN
DC Adaptor
Power Cable
Optical Cable
ACCESSORIES
PAIRING YOUR DEVICE FOR THE FIRST TIME
CONTROL PANEL
AND REMOTE CONTROL:
The sound system settings
can be adjusted with the
control panel and/or the
sound system remote control:
SCROLL SOURCE OPTIONS
SCROLL EQ SETTINGS
1. Power on the unit by pressing the Power button.
2. Set the indicator to BL by either scrolling the source selection button on the panel or pressing the PAIR
button on the remote control.
The pairing indicator will flash blue quickly. When pairing, remain within 3 feet of the unit.
3. Use the controls of your device to select Fireplace to pair.
4. If your device requests a password, enter the default password 0 0 0 0
Refer to the user’s manual for your specific device for instructions on pairing and connecting devices.
5. When successfully paired and connected, a beep will issue from the sound system and the Pairing
Indicator will display a solid blue light.
After initial pairing, the unit will stay paired unless unpaired manually by the user or erased due to a
reset of the device.
6. If your device should become unpaired or you find it is unable to connect, repeat the above steps.

13
Replacing the Remote Control Batteries
AAA 1.5V
AAA 1.5V
Disposal of Used Batteries
A battery may contain hazardous substances that could be
endangering the environment and human health.
CARE AND MAINTENANCE
When the sound system remote control (Q) stops
operating or its range seems reduced, it is time to replace
the batteries. Note:The batteries should be removed if
the product is to be left unused for a long time.
1. The battery compartment is located on the back
of the sound system remote control (Q).
2. Remove battery cover from the back of sound system
remote control (Q) and remove the old batteries.
3. Insert 2pcs AAA batteries, ensuring the polarities of
the battery match the inside of the battery
compartment.
4. Re-insert the battery door.
Note: Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc), or rechargeable (nicad, nimh, etc) batteries.
Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from
the product.
Harmful if swallowed.
• This symbol marked on the battery and/or packaging indicates that
used battery shall not be treated as municipal waste. Instead it shall
be left at the appropriate collection point for recycling.
• By ensuring the used battery is disposed of correctly, you will help
prevent potential negative consequences for the environment and
human health. The recycling of materials will help to conserve
natural resources.
• Do not dispose of batteries in fire. batteries may explode or leak.
For more information about collection and recycling of used batteries,
please contact your local municipality, your waste disposal service or
the point-of-sale where you purchased this battery.

14
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants that your new Electric fireplace is free from manufacturing and material
defects for a period of one year from date of purchase, subject to the following conditions and
limitations.
Install and operate this Electric fireplace in accordance with the installation and operating instructions
furnished with the product at all times. Any unauthorized repair, alteration, willful abuse, accident, or
misuse of the product shall nullify this warranty.
This warranty is non-transferable, and is made to the original owner, provided that the purchase was
made through an authorized supplier of the product.
The warranty is limited to the repair or replacement of part(s) found to be defective in material or
workmanship, provided that such part(s) have been subjected to normal conditions of use and
service, after said defect is confirmed by the manufacturer’s inspection.
The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by
refunding the wholesale price of the defective part(s).
Any installation, labor, construction, transportation, or other related costs/expenses arising from
defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor
shall the manufacturer assume responsibility for same.
The owner/user assumes all other risks, if any, including the risk of any direct, indirect or
consequential loss or damage arising out of the use, or inability to use the product, except as
provided by law.
All other warranties-expressed or implied-with respect to the product, its components and
accessories, or any obligations/liabilities on the part of the manufacturer are hereby expressly
excluded.
The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other
liabilities with respect to the sale of the product.
The warranties as outlined within this document do not apply to non accessories used in conjunction
with the installation of this product.
This warranty is void if:
1. The fireplace is subjected to prolonged periods of dampness or condensation.
2. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
3. You do not have the original receipt of purchase.

Console média de
121,9 cm (48 po)
pour foyer
English p. 1
Español p. 29
www.greentouchhome.com
Date d’achat _______________________
INSTRUCTIONS D’UTILISATION, D’ASSEMBLAGE
ET DE MAINTENANCE
MODÈLE # 1274SB-23-258; 1274SB-23-259
15

16
CONTENU DE L’EMBALLAGE
A Dessus 1
B Panneau Central 1
C Cloison Centrale Gauche 1
D Cloison Centrale Droite 1
E Paroi Extérieure Gauche 1
F Paroi Extérieure Droite 1
G Porte Gauche 1
H Porte Droite 1
I Tablette 2
J Panneau Arrière 2
K Base 1
L Moulure Avant
Support D'insert En Bois
1
M
Foyer Encastrable
2
N
Télécommande
1
O 1
P Pile 2
Q Télécommande Du
Système Audio
1
PIÈCE DESCRIPTION QUANTITÉ
PAIR
EQ
A
J
G
M
M
D
I
F
H
K
L
N
P O
Q
E
C
B
J

17
CONTENUS MATÉRIELS (NON REPRÉSENTÉS EN TAILLE RÉELLE)
PIÈCE DESCRIPTION QUANTITÉ
AA Groujon En Bois 4
BB Boulon Long 5
CC Rondelle 5
DD Vis Pour Le Panneau Arrière 16
EE Boulon 18
FF Goupille à Tablette 8
GG Crayon à Retouche 1
HH Tirette de porte 2
II Boulon à Tirette De Porte 4
AA BB CC DD EE FF
HH II
GG

18
QUINCAILLERIE UTILISÉE
Groujon En Bois x 4
AA
INSTRUCTIONS POUR L’ASSEMBLAGE
2. Insérez deux chevilles en bois (AA) de chaque
côté du panneau central (B).
QUINCAILLERIE UTILISÉE
BB
CC
Boulon Long x 3
Rondelle x 3
1. Placez la moulure avant (L) sur la base (K), sécurisez
avec trois rondelles (CC) et deux boulon long (BB).
PRÉPARATION
Avant de commencer l’assemblage de l’article,
assurez-vous d’avoir toutes les pièces. Comparez
le contenu de l’emballage avec la liste des pièces
et celle de la quincaillerie incluse. S’il y a des
pièces manquantes ou endommagées, ne tentez
pas d’assembler l’article.
Temps d’assemblage approximatif :
45 minutes.
Outil nécessaire pour l’assemblage
(non inclus) : tournevis cruciforme.
B
AA
2
K
LCC
BB
1
2
1

19
INSTRUCTIONS POUR L’ASSEMBLAGE (SUITE)
QUINCAILLERIE UTILISÉE
Boulon x 4
EE
4. Placez l'assemblage de l'étape 3 sur la base (K),
fixez avec quatre boulons (EE).
5. Attachez la paroi extérieure droite (F), fixez avec
deux boulons (EE).
Répétez l'opération précédente pour la paroi
extérieure gauche (E).
3. Alignez les chevilles du panneau central (B) à la
paroi centrale gauche (C) et au panneau central
droit (D). Insérez les chevilles dans les trous
prépercés et appuyez fortement.
QUINCAILLERIE UTILISÉE
Boulon x 4
EE
C
B
D
3
EE K
1
1
2
4
EE
E
K
F
1
1
5
2

20
INSTRUCTIONS POUR L’ASSEMBLAGE (SUITE)
QUINCAILLERIE UTILISÉE
Boulon x 10
EE
6. Attachez la partie supérieure (A), fixez par en
dessous à l’aide de dix boulons (EE).
QUINCAILLERIE UTILISÉE
Vis pour le panneau arrière x 16
DD
7. En vous positionnant derrière l’assemblage, fixez
les panneaux arrière (J) à la zone se trouvant
en arrière des tablettes, et ce, à l’aide des vis du
panneau arrière (DD).
Répétez l'opération précédente pour le panneau
arrière (J).
8. Tenez la porte et alignez le corps de la penture
avec la plaque de la penture assemblée au mur
du foyer. Alignez et glissez les crochets/prises
sur le corps de la penture dans les niches de la
plaque d’assemblage tout en poussant légèrement
la porte vers l’arrière de la cheminée du foyer.
Ensuite, appuyez sur la partie arrière du corps de
la penture jusqu’à ce que vous l’entendiez faire
« clic » Répétez pour les autres pentures.
Pour retirer, appuyez sur le bouton carré à l’arrière
du corps de la penture pour dégager la penture
du support d’assemblage. Déverrouillez les deux
pentures et tirez la porte vers l’extérieur du corps
du foyer.
1
J
J
DD
2
7
A
E
C
D
F
B
1
1
EE
6
2
1
8
2
3