Screen Innovations Zero Edge / Fixed User manual
Zero Edge / Fixed
Installation Instructions
INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER.
400025 | v. 2.0 | July 2023
SI WARRANTY
11°
11°
SCREEN
Better
Best
Good
36”-42”
(91cm - 106cm)
SUGGESTED PROJECTOR PLACEMENT
3
TABLE OF CONTENTS
For more technical support questions - Call: 512.832.6939 or email: suppor[email protected]
Hours of Support: 7:30am – 5pm CST | screeninnovations.com
Please visit support.
screeninnovations.
com to nd all the
updated documents,
drivers and tutorial
videos.
Use this QR code to
see the video tutorials
for Black Diamond
or Short Throw snap
attachment method
Use this QR code
to see the video
tutorials for Slate
material.
Determine Frame Type 4
Standard - Inner Frame Assembly 5 - 6
Split - Inner Frame Assembly 7 - 9
LED Lights Attachment 10 - 11
Determine Your Material 12
Material Attachment Sequence – All Materials 12
Material Rolling 12
Black Diamond & Short Throw Material Only 13
Slate, Pure Material Attachment 14
Maestro 2 (White) – AT Material – Attachment 15 - 16
PVC - AT Material Attachment 16
Trim Attachment (Zero Edge and Fixed frame trim) 17 - 18
Logo Attachment 19
Wall Mounting 20
Flown Mounting 21
IR Lighting Hex Codes 22
IP (Zigbee) Controlled Lighting Setup 23
Connect To LED Strip 23
Mounting 23
Zigbee 3.0 App Control Instruction 23
4
7
5
DETERMINE FRAME TYPE
Determine the frame type ordered. If the frame is 120” and above it will be Split frame assembly,
anything below 120” will be standard frame assembly.
Split Frame
Standard Frame
5
STANDARD - INNER FRAME ASSEMBLY
NOTE: Look for the SI logo or a hole for the LED kit lighting (if ordered), that should be the bottom
horizontal frame.
2
1
Thin Bracket
Thick
Bracket
6
It is a critical step to square the frame.
4
3
A
STANDARD - INNER FRAME ASSEMBLY
Note: If LED lights were ordered, refer to page 10 for
instructions on attaching LED lights to the screen frame.
7
SPLIT - INNER FRAME ASSEMBLY
2
NOTE: The Horizontal inner frame with no.16 hole in the middle is the top of the screen, the horizontal
innerframe with slipping nuts is the bottom of the screen)
1
Thin Bracket plates Splice bars
Thick Bracket plates
Flat Metal plates
NOTE: Look for the SI logo to determine the bottom horizontal frame.
Prep Paper
8
SPLIT - INNER FRAME ASSEMBLY
It is a critical step to square the frame.
4
3
A
Note: If LED lights were ordered, refer to page 10 for
instructions on attaching LED lights to the screen frame.
9
5
SPLIT - INNER FRAME ASSEMBLY
Note: Our Mounting plate can be adjusted to the left or right when mounting the vertical support bar to
accomodate a center channel behind the screen when using acoustically transparent material.
10
3
1
2
LED LIGHTS ATTACHMENT
LED Controller
hole for feeding wire
11
5
LED LIGHTS ATTACHMENT
Scan this QR code to see the video for LED kit troubleshooting.
+12V
B
G
R
+12V
B
G
R
4Note: Use caution in the next steps; do not kink or fold the light strip, which will cause damage
in the circuit. Use the foam strips provided to losely wrap LEDs around the corners.
12
DETERMINE YOUR MATERIAL
PVC – AT Material (Slate AT, Pure AT)
Non – AT Material (Slate, Pure, Short Throw) Refer to page 13
Maestro 2 – White AT Material Refer to page 14 - 15
Refer to page 15
7
7
11 11
5
8
8
6
9
12 12
10
1
3
4
2
MATERIAL ATTACHMENT SEQUENCE – ALL MATERIALS
MATERIAL ROLLING
13
1
Note: Wear gloves when handling material. Carefully unroll the screen material onto a clean oor. Take
care to not bend or crease the screen material.
SLATE, PURE, SHORT THROW MATERIAL ATTACHMENT
2
Note: Refer to attachment sequence image on page 12.
14
1
3
4
Note: Wear gloves when handling the material. Carefully unroll the screen material onto a clean oor.
Take care to not bend or crease the screen material.
2
MAESTRO 2 – AT MATERIAL (WITH BLACK BACKER) –
ATTACHMENT
15
3Make sure the screen material is centered around the frame before proceeding.
Once all snaps are attached (following the sequence above), ip screen over and make sure
that the screen material is at and taut everywhere.
PVC AT MATERIAL ATTACHMENT
(Slate AT, Pure AT)
MAESTRO 2 – AT MATERIAL (WITH BLACK BACKER) –
ATTACHMENT
16
1
TRIM ATTACHMENT
Note: Trim for Fixed screen will be 2” thick, v/s the Zero Edge will be 0.5”.
17
TRIM ATTACHMENT
Split Frame Only
2
Split Frame Only:
18
LEVEL
Structural Support
Structural Support
3
3
4
"
(9.5 cm)
TOP OF VIEWING
1
WALL MOUNTING
Note: Drill the holes to a rm stud; use a stud nder to locate the studs.
Note: Screens above 133” in diagonal with come with 3 brackets.
2
19
1
2
FLOWN MOUNTING
Note: If pulled too far, the screen can be lowered by pushing down on the top of the ying mount.
Note: Make sure to drill the holes into a beam that can support the weight of the screen.
20
IR LIGHTING HEX CODES (TO USE FOR DIFFERENT RE-
MOTE CONTROL - REF THE CODES BELOW)
Table of contents
Other Screen Innovations TV Mount manuals
Popular TV Mount manuals by other brands
IZI Mounting
IZI Mounting TWB-11 installation instructions
AmazonBasics
AmazonBasics B07QG3LV9J manual
Techly
Techly ICA-PLB 162M user manual
Moog Videolarm
Moog Videolarm PRM30G Installation and operation instructions
Mounting Dream
Mounting Dream MD2210 installation instructions
arkitect
arkitect ATVBTS14 instruction manual