SDC Emlock 1511 User manual

sdcsecurity.com [e-mail]
SECURITY DOOR CONTROLS
EZ Option Upgrade Kits - Emlock© 1511, 1513, 1571, 1573
EMLock EZ Kits
Field Upgradeable Option Modules for 1511, 1513, 1571, 1573
SDC’s patented EMLock design represents the pinnacle of magnetic lock evolution.
The modular EMLock assembly makes them easy to stock, install, upgrade and maintain.
EZ-B-10 MAGNETIC
BOND SENSOR
Modular Kit
EZ-T-10 TIMER INPUT MODULE
Modular Kit
EZ-D-10: DOOR POSITION SENSOR
Modular Kit
EZ-A: ANTI-TAMPER SWITCH
Modular Kit
Field Upgradeable by Distributors, Installers and Maintenance Staff
No need to ever remove a lock from the frame to upgrade or exchange
internal components.
FIELD UPGRADE
• Relock Delay Timer
• Magnetic Bond Sensor
• Door Status Sensors
• Anti-Tamper Switch
• Holding Force Upgrade
• Energy Saver Upgrade

© 2007 Security Door Controls Printed in the U.S.A. LIT-Datasheet date qty vendor
SECURITY DOOR CONTROLS
www.sdcsecurity.com [e-mail]
[t] 800.413.8783 805.494.0622 [f] 805.494.8861
801 Avenida Acaso, Camarillo CA 93012 • PO Box 3670, Camarillo CA 93011-3670
SECURITY DOOR CONTROLS
8
sdcsecurity.com [e-mail]
EZ-T-10 TIMER INPUT MODULE
Modular Kit
Relock Delay Timer, Adjustable 1 to 30 Seconds.
Application: The Timer Input Module delays relocking of access controlled doors to provide persons ample time needed
for entry or egress. Momentary interruption of power to the lock input activates the timer module.
Momentary, N.C. Dry Contact required. Contact actuation unlocks the door for 1 – 30 seconds.

sdcsecurity.com [e-mail]
SECURITY DOOR CONTROLS
EZ Option Upgrade Kits - Emlock© 1511, 1513, 1571, 1573
EZ-B-10 MAGNETIC BOND SENSOR
Modular Kit
While a Door Status Sensor indicates the door is open
or closed, SDC’s Magnetic Bond Sensor provides higher
security monitoring by indicating the locked / unlocked
mode, tampering and low holding force. The use of
both the door status and magnetic bond sensor is
recommended for high security applications.
Application: Lock secure status annunciation,
mantrap system logic,
CCTV camera activation.
Output: SPDT Dry Contact,
250 mA @ 12/24VDC
* Not available for 1513, 1573

© 2007 Security Door Controls Printed in the U.S.A. LIT-Datasheet date qty vendor
SECURITY DOOR CONTROLS
www.sdcsecurity.com [e-mail]
[t] 800.413.8783 805.494.0622 [f] 805.494.8861
801 Avenida Acaso, Camarillo CA 93012 • PO Box 3670, Camarillo CA 93011-3670
SECURITY DOOR CONTROLS
8
sdcsecurity.com [e-mail]
EZ-D-10: DOOR
POSITION SENSOR
Modular Kit
Indicates the door is open
and closed.
Application:
Door position status annunciation,
anti-tailgating, interlock, mantrap and
communicating bathroom system
logic.
Output:
SPDT Dry Contact, 250 mA
@ 12/24VDC
EZ-A: ANTI-TAMPER
SWITCH - Modular Kit
Indicates cover plate removal
Output:
SPDT Dry Contact, 3 Amp @ 12/24VDC
* Not available for 1513, 1573

sdcsecurity.com [e-mail]
SECURITY DOOR CONTROLS
EZ Option Upgrade Kits - Emlock© 1511, 1513, 1571, 1573
EZ – 1510W Holding Force Upgrade
EZ – 1570W Energy Saver Upgrade
All 1511, 1512, 1513, 1571, 1572 and 1573 magnetic coils are field interchangeable without removing the lock from the frame. There is no reason
to remove and ship a lock for exchange.
Benefits of this interchangeability include:
• EZ-1510W Holding Force Upgrade: Exchange 1200 lb coil with
1650 lb holding force coil
• EZ-1570W Energy Saver Upgrade: Save on power supply and
long term energy costs by exchanging 8.4 Watt,1650 lb coil
with 3 Watt, 1200 lb holding force coil
• Eliminate labor, shipping costs and time associated with special
orders or complete lock removal and replacement.
Applications
Distributors with limited stock may exchange coils to fulfill specific
special sales needs, i.e. a 1570 with Dark Bronze finish may be
upgraded to a 1511 with dark bronze finish and visa versa.
Installers may field upgrade to an Energy Saver where power supply
capacity is limited or upgrade to higher holding force where 1200 lbs
holding force proves inadequate, i.e. psychiatric or rehab center
applications.

© 2007 Security Door Controls Printed in the U.S.A. LIT-Datasheet date qty vendor
SECURITY DOOR CONTROLS
www.sdcsecurity.com [e-mail]
[t] 800.413.8783 805.494.0622 [f] 805.494.8861
801 Avenida Acaso, Camarillo CA 93012 • PO Box 3670, Camarillo CA 93011-3670
SECURITY DOOR CONTROLS
8
sdcsecurity.com [e-mail]

sdcsecurity.com [e-mail]
SECURITY DOOR CONTROLS
EZ Option Upgrade Kits - Emlock© 1512 / 1572
2Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate
Place anti-tamper switch as shown.
Cover depresses switch
2
Attach magnetic core
wire connector to
timer module
Connect
output wires
of timermodule
to input terminals
1 and 2 of standards
input module.
5 6 Position timer modules
between posts
Cradle
Position Posts
9Attach cover plate
T - Timer input
module
EZ-T-10 TIMER INPUT MODULE
Modular Kit
1 2 Re-install armature per installation instructionsAttach door status module to each armature
EZ-D-10: DOOR POSITION SENSOR
Modular Kit
EZ-A: ANTI-TAMPER SWITCH
Modular Kit
EMLock EZ Upgrade Kits
Field Upgradeable Option Modules for 1512 and 1572
SDC’s patented EMLock design represents the pinnacle of magnetic lock evolution.
The modular EMLock assembly makes them easy to stock, install, upgrade and maintain.
Field Upgradeable by Distributors, Installers and Maintenance Staff
No need to ever remove a lock from the frame to upgrade or exchange
internal components.
FIELD UPGRADE
• Relock Delay Timer
• Magnetic Bond Sensor
• Door Status Sensors
• Anti-Tamper Switch
• Holding Force Upgrade
• Energy Saver Upgrade
9Attach cover plate.
5
The Magnetic Bond
Sensor should be
positioned as shown
below, after step 4.
+
3
4
5
6
7
8

SECURITY DOOR CONTROLS
www.sdcsecurity.com [e-mail]
[t] 800.413.8783 805.494.0622 [f] 805.494.8861
801 Avenida Acaso, Camarillo CA 93012 • PO Box 3670, Camarillo CA 93011-3670
SECURITY DOOR CONTROLS
8
sdcsecurity.com [e-mail]
© 2010 Security Door Controls Printed in the U.S.A. LIT-EZ Option Kit Upgrades 12.10
Remove cover plate screws
1
Attach magnetic core
wire connector to
timer module
Connect
output wires
of timermodule
to input terminals
1 and 2 of standards
input module.
5
Remove cover plate
2
6Position timer modules
between posts
Adjustable 1 - 30 Seconds
Typical factory setting approximately 5 seconds
Turn clockwise to increase time
Cradle
Position Posts
PC Board
9Attach cover plate
T - Timer input
module
EZ-T-10 TIMER INPUT MODULE
Modular Kit
Remove cover plate screws
Attach magnetic core
wire connector to
timer module
Connect
output wires
of timermodule
to input terminals
1 and 2 of standards
input module.
Remove cover plate
2
6
Carefully lift input
modules from case
3
7
Position timer modules
between posts
Adjustable 1 - 30 Seconds
Typical factory setting approximately 5 seconds
Turn clockwise to increase time
Cradle
Position Posts
PC Board
D2
Standard
input module
Remove cover plate
2
6
Carefully lift input
modules from case
3
7
Position timer modules
between posts
Adjustable 1 - 30 Seconds
Typical factory setting approximately 5 seconds
Turn clockwise to increase time
Cradle
Position Posts
PC Board
D2
Standard
input module
Disconnect magnetic
cord wires and remove
input module
4
T - Timer module wiring8
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Access and Egress Control
Momentary
N.C. Dry Contact
Contact actuation unlocks
door for 1 - 30 seconds
Remove cover plate screws
1
Attach magnetic core
wire connector to
timer module
Connect
output wires
of timermodule
to input terminals
1 and 2 of standards
input module.
5
Remove cover plate
2
6Position timer modules
between posts
Adjustable 1 - 30 Seconds
Typical factory setting approximately 5 seconds
Turn clockwise to increase time
Cradle
Position Posts
PC Board
9Attach cover plate
T - Timer input
module
Remove cover plate screws
1
Attach magnetic core
wire connector to
timer module
Connect
output wires
of timermodule
to input terminals
1 and 2 of standards
input module.
5
Remove cover plate
2
6Position timer modules
between posts
Adjustable 1 - 30 Seconds
Typical factory setting approximately 5 seconds
Turn clockwise to increase time
Cradle
Position Posts
PC Board
9Attach cover plate
T - Timer input
module
Carefully lift input
modules from case
3
7
Disconnect magnetic
cord wires and remove
input module
4
T - Timer module wiring8
Position timer modules
between posts
Adjustable 1 - 30 Seconds
Typical factory setting approximately 5 seconds
Turn clockwise to increase time
D2
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Access and Egress Control
Momentary
N.C. Dry Contact
Contact actuation unlocks
door for 1 - 30 seconds
Standard
input module
Disconnect magnetic
cord wires and remove
input module
4
T - Timer module wiring8
Position timer modules
between posts
Adjustable 1 - 30 Seconds
Typical factory setting approximately 5 seconds
Turn clockwise to increase time
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Access and Egress Control
Momentary
N.C. Dry Contact
Contact actuation unlocks
door for 1 - 30 seconds
Remove cover plate screws
1
Attach magnetic core
wire connector to
timer module
Connect
output wires
of timermodule
to input terminals
1 and 2 of standards
input module.
5
9Attach cover plate
T - Timer input
module
Relock Delay Timer, Adjustable 1 to 30 Seconds. 1 only required for double EMLock®.
Application: The Timer Input Module delays relocking of access controlled doors to provide persons ample time needed
for entry or egress. Momentary interruption of power to the lock input activates the timer module.
Momentary, N.C. Dry Contact required. Contact actuation unlocks the door for 1 – 30 seconds.
Only 1 timer module is required for double Emlocks®.
1 only required

sdcsecurity.com [e-mail]
SECURITY DOOR CONTROLS
EZ Option Upgrade Kits - Emlock© 1512 / 1572
Remove cover plate screws.
1 2 Remove
cover plate.
6Place magnetic coil firmly
between core lamination
as shown.
Connect
magnetic
bond sensor
wiresto the input
module B Option
connector as shown.
5
The Magnetic Bond
Sensor should be
positioned as shown
below, after step 4.
+
3
4
5
6
7
8
EZ-B-10-2 MAGNETIC BOND SENSOR
Modular Kit
Remove cover plate screws. 2Remove
cover plate.
3
6 7
Liftinput module
andmagnetic coil
from the case.
Place magnetic coil firmly
between core lamination
as shown.
Connect
magnetic
bond sensor
wiresto the input
module B Option
connector as shown.
3
Place input module vertically
between post at each
side of case.
The Magnetic Bond
Sensorshould be
positioned as shown
below, after step 4.
Cradle
Position Posts
+
3
4
5
6
7
8
+
3
4
5
6
7
8
+
3
4
5
6
7
8
2Remove
cover plate.
3
6 7
Lift input module
and magnetic coil
from the case.
Place magnetic coil firmly
between core lamination
as shown.
Connect
magnetic
bond sensor
wires to the input
module B Option
connector as shown.
3
Place input module vertically
betweenpost at each
side of case.
The Magnetic Bond
Sensor should be
positioned as shown
below, after step 4.
Cradle
Position Posts
PC Board
+
3
4
5
6
7
8
+
3
4
5
6
7
8
Input module wiring.8
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
4Remove 2 screw
from the case
bottom.
Place the
Magnetic Bond
Sensors at the
base of each
Magnetic Core.
Secure sensor
in place with
screw as
shown.
Remove cover plate screws.
1 2 Remove
cover plate.
6
9Attach cover plate.
Place magnetic coilfirmly
between core lamination
as shown.
connector as shown.
5
The Magnetic Bond
Sensor should be
positioned as shown
below, after step 4.
+
3
4
5
6
7
8
Remove cover plate screws.
1 2 Remove
cover plate.
6
9Attach cover plate.
Place magnetic coil firmly
between core lamination
as shown.
Connect
magnetic
bond sensor
wires to theinput
module B Option
connector as shown.
5
The Magnetic Bond
Sensor should be
positioned as shown
below, after step 4.
+
3
4
5
6
7
8
Input module wiring.8
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
3
7
Lift input module
and magnetic coil
from the case.
43
Place input module vertically
between post at each
side of case.
Remove 2screw
from the case
bottom.
Place the
Magnetic Bond
Sensors at the
base of each
Magnetic Core.
Securesensor
in place with
screw as
shown.
Cradle
Position Posts
PC Board
+
3
4
5
6
7
8
+
3
4
5
6
7
8
Input module wiring.8
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Liftinput module
and magnetic coil
from the case.
4
Place input module vertically
between post at each
Remove 2screw
from the case
bottom.
Place the
Magnetic Bond
Sensors at the
base of each
Magnetic Core.
Securesensor
in place with
screw as
shown.
Cradle
Position Posts
PC Board
+
3
4
5
6
7
8
+
3
4
5
6
7
8
Remove cover plate screws.
1
9
Attach cover plate.
5
The Magnetic Bond
Sensor should be
positioned as shown
below, after step4.
+
3
4
5
6
7
8
While a Door Status Sensor indicates the door is open
or closed, SDC’s Magnetic Bond Sensor provides higher
security monitoring by indicating the locked / unlocked
mode, tampering and low voltage. The use of
both the door status and magnetic bond sensor is
recommended for high security applications.
Application: Lock secure status annunciation,
mantrap system logic,
CCTV camera activation.
Output: 2 Contacts provided
2-SPDT Dry Contact,
250 mA @ 12/24VDC
Specify 2 for 1512, 1572

SECURITY DOOR CONTROLS
www.sdcsecurity.com [e-mail]
[t] 800.413.8783 805.494.0622 [f] 805.494.8861
801 Avenida Acaso, Camarillo CA 93012 • PO Box 3670, Camarillo CA 93011-3670
SECURITY DOOR CONTROLS
8
sdcsecurity.com [e-mail]
© 2010 Security Door Controls Printed in the U.S.A. LIT-EZ Option Kit Upgrades 12.10
EZ-D-10-2: DOOR
POSITION SENSOR
Modular Kit
Indicates the door is open
and closed.
Application:
Door position status annunciation,
anti-tailgating, interlock, mantrap
and communicating bathroom
system logic.
Output: 2 Modules provided
SPDT Dry Contact, 250 mA
@ 12/24VDC
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
1 2
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
1 2
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
Com
No
NC
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Locked Unlocked
3 4
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
Com
No
NC
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Locked Unlocked
3 4
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
1 2
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
3
2
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
Com
No
NC
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Locked Unlocked
3 4
13 4 2Input module wiring. Annunciation
Re-install armature per installation instructionsAttach door status module to each armature
Remove cover plate Replace cover plate
Place anti-tamper switch as shown.
Cover depresses switch
arm when mounted
Anti-tamper wiring
Com
No
NC
B Option
Connector
B Option
Magnetic Bond Sensor
D Option
Door Status Sensor
Magnetic Core
Connector
12 or 24 VDC
LOCKED - NO
COM
UNLOCKED - NC
CLOSED - NO
COM
OPEN - NC
Locked Unlocked
4
EZ-A: ANTI-TAMPER
SWITCH - Modular Kit
Indicates cover plate removal
Output:
SPDT Dry Contact, 3 Amp @ 12/24VDC
1 only required