SDC WPT User manual

P:\INSTALLATION INST\Accessories\INST-WPT.vsd REV - 01/19 Page 1
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email [e-mail]
INSTALLATION INSTRUCTIONS
WPT Wireless Power Transfer
Technical Specifications:
Note – For Use with Fail-Secure (Power to Unlock) Locks Only
Input Power (Frame Side): 600mA @ 24VDC
Output Power (Door Side): 600mA/300mA @ 12/24VDC
{Field Selectable}
Maximum Door Gap: 1/4” (~7mm)
Maximum Tolerance
with 3/16" (5mm) Gap: Horizontal < 5/64" (2mm)
Vertical < 5/64" (2mm)
Dry Inputs (Frame Side): (2) Door Unlock Trigger (Timed)
1. 4 Second Fixed
2. 1-90 Seconds Manual
Dry Inputs (Door Side) (2) Relay Activation
for REX, Latch Status, etc.
Dry Outputs (Frame Side): (2) SPDT Relay, 1A @ 30VDC
(2) Solid State Relay, N/O
100mA @ 60VDC
LED Indicators: Frame & Door Side
Operating Temperature: -4°F – 140°F(-20°C – 60°C)
Compliance: UL1034; UL10C for 3 Hours,
FCC Part 15
801 Avenida Acaso, Camarillo, Ca. 93012 • [phone] •
www.sdcsecurity.com • E-mail: [email protected]

WPT Dimensions
FRAME SIDE
DOOR SIDE
5-1/8" (131mm)
Front
View
4-5/8"(118mm)
Rear
View
4-1/8" (105mm)
Side
View
1mm
1-1/2"
(37mm)
1/8"
(3mm)
1-7/8"Minimum
recommendeddepth
Front
View Rear
View
1"
(25mm)
Side
View
1mm
1-1/2"
(37mm)
1/8"
(3mm)
1-7/8"Minimum
recommendeddepth
4-1/8" (105mm)
1"
(25mm)
5-1/8" (131mm)
4-5/8" (118mm)
P:\INSTALLATION INST\Accessories\INST-WPT.vsd REV - 01/19 Page 2
Frame Status LED
Alternates Green/
Amber when powered
Solid Red during
power transfer
Door Status LED
Flashing Red when
door is closed &
locked
Solid Red during
power transfer

P:\INSTALLATION INST\Accessories\INST-WPT.vsd REV - 01/19 Page 3
WPT Installation & Wiring
Note: Optimal performance of the WPT will depend on minimizing the door gap, and using the
supplied templates. Although the WPT allows for some horizontal and vertical misalignment, these
tolerances will decrease as the door gap increases.
1. Inspect the door & frame, and apply the templates at the desired location. The WPT may
be installed on the latch side, hinge side, or top of the door.
2. For metal door installations:
2a. Center punch the tab-mounting screw
locations and counter-sink for M3 screw.
Package Contents:
Door Side Unit
Frame Side Unit
Door Template
Frame Template
4" Wire Harnesses
> (2) 2-wire
> (1) 3-wire
> (2) 4-wire
> (1) 6-wire
Wood Screws
Metal Screws
Mounting Tabs
1a.
1b. Using the door template as a guide,
apply the template on the frame, aligning
the horizontal & vertical centerlines.
2b. Saw or rout out the entire main pocket.

2c. Verify that the WPT face fits in the cutout,
and file as necessary. 2d. Install mounting tabs using M3 screws
3. For wood door installations, use the recommended wood door jig, or follow the
steps below:
3a. Drill (2) 1" (25mm) diameter holes,
1/8" (3mm) in depth as shown on the template 3b. Drill out the main WPT pocket to a
minimum depth of 1-7/8" (48mm), and
diameter of 1" (25mm)
3c. Carefully use a chisel to straighten the
sides. 3d. Verify that the WPT unit fits in the cutout,
and file as necessary.
P:\INSTALLATION INST\Accessories\INST-WPT.vsd REV - 01/19 Page 4

3e. For the door side unit, drill a wiring channel
to the electrified device to be powered.
4. Select the Lock Output Voltage. Use the
slide switch on the back of the door side unit
to select the appropriate lock voltage.
UP DOWN
5. Repeat steps 2 or 3 for the installation of the frame side unit in a metal or wood frame.
P:\INSTALLATION INST\Accessories\INST-WPT.vsd REV - 01/19 Page 5

P:\INSTALLATION INST\Accessories\INST-WPT.vsd REV - 01/19 Page 6
6. Terminate wiring to both of the WPT units.
6a. Wiring Overview. Items marked as “Required” are the minimum connections required to
control an electrified lockset. Select Momentary Activation, or Maintained, or both. Use the
wiring diagrams on Page 7 as a reference.
Pigtail WireColor Function Required
BLUE
GRAY
YELLOW
WHITE
ORANGE 12or24VDC(+){Fieldselectable}
BLACK 12or24VDC(‐){Fieldselectable}
LockPower
Output
X
Relay#1Activation{ShorttoActivate}
Relay#2Activation{ShorttoActivate}
WPTUnit
DOOR
Relay
Activation
Inputs
Pigtail WireColor Function Required
RED 24VDC(+)@600mA
BLACK Ground
GREEN MomentaryActivation(fixed4second)
YELLOW ActivationCommon
BROWN MaintainedActivation(upto90secs.)
BLUE
GRAY
YELLOW
WHITE
BLACK/WHITE NormallyClosed#1
GRAY/WHITE Common#1
PURPLE/WHITE NormallyOpen#1
GREEN/WHITE NormallyClosed#2
BLACK/YELLOW Common#2
PINK NormallyOpen#2
X
X
DoorStatus(Closedwhendoorclosed)
ErrorStatus(Closedwhentampered)
FRAME
InputPower
(Continuous)
Activation
Triggers
SolidState
Outputs
Relay
Outputs
WPTUnit

6b. Wiring Examples
P:\INSTALLATION INST\Accessories\INST-WPT.vsd REV - 01/19 Page 6
7. Mount both WPT units using the appropriate screws. Apply continuous power to the frame
side. If using a momentary switch to activate the lock, hold for a second or two, then release.
Power will be provided to the lock for approximately 4 seconds.
12VDC
24VDC
ORG (+)
BLK (-)
BLU
GRY
YEL
WHT
24VDC
Fail-secure
Electrified
Lockset
300mA
@24VDC max
(+)
(-)
SET for
24VDC
Momentary
Switch #1
(N/O)
{REX from
Lockset}
{SDC Z7200 Cylindrical or
Z7800 Mortise}
RED (+)
BLK (-)
GRN
YEL
BRN
BLU
GRY
YEL
WHT
BLK/WHT (N/C)
GRY/WHT (COM)
VIO/WHT (N/O)
GRN/WHT
BLK/YEL
PNK
24VDC (+)
24VDC (-)
Momentary
Push Button or
Access Control
(N/O)
LED (+)
(-)
Status LED
(100mA max)
{Lock Activation –
Fixed 4 sec. timer}
}
Relay Output #1
{Follows REX Switch}
External
StatusLED
(ByOthers)
100mAmax