Seac PARTNER User manual

PARTNER
www.seacsub.com
MULTIPURPOSE
FREEDIVING
WATCH

2

PARTNER
3
MULTIPURPOSE FREEDIVING WATCH
Congratulations on your purchase of a Partner Seac multipurpose diving watch.
Check www.seacsub.com for any updates to this manual.
GENERAL WARNINGS
• WARNING! Read this entire manual before using your SEAC multipurpose watch.
Incorrect use will void the warranty and could cause permanent damage to
the instrument.
• WARNING! Freediving entails risks of syncope, taravana, pulmonary edema,
and hemoptysis; even a careful reading of this manual cannot exclude
potential dangers underwater.
Anyone who does not understand or knowingly accept these dangers must
not dive with a SEAC instrument.
ICONS
Diving Depth Temperature
Stopwatch Countdown Timer
World Time EL Backlight
Chime
5
5 Alarms
11
100 Year Calendar Pacer
100
100M Water Resistant Battery (CR2032)

4
BUTTONS
The function of each button is shown below.
A- Reset / Stop
B- Mode
C- EL backlight /
D- Start / Split 1 / +
DISPL AY
The screen is shown in below:
Year Date
Diver attention
symbol Chime
Stopwatch Alarm
Timer Seconds
Hour Low power
indicator
Minutes Daylight saving
time
Dive
Day of week

PARTNER
5
LOW POWER
lf the battery level is too low, the
symbol will display until a new
battery is installed.
MODE SELECTION
• Press “B” to change the mode in the following sequence:
Timekeeping Mode Diving Mode Record Mode Alarm Mode
Countdown Time Mode World Time Mode Pacer Mode Stopwatch
Mode.
• Alarm mode, countdown timer mode, world time mode, and pacer mode can
be set ON/OFF under the time mode setting (See Page 6).
TIMEKEEPING
• Hour, Minutes, Seconds, Year,
Month, Date, Day of the week;
• 12/24H Format;
• 100-year calendar (2000 - 2099).
DIVING
• Maximum diving depth: 100 m or
330 ft;
• Maximum time for a single dive:
59’59”;
• Temperature range:
-9.9 - 60.0°C or 14.2 - 140°F.

6
RECORD
• Depth, Temperature, Dive time,
Surface time;
• 30 records (R01 - R30);
• PARTNER can store dive data
99times (F01 - 99) max.
ALARM
• 5 alarms;
• Chime.
In Alarm mode, the screen on the
right appears automatically after 2s.
COUNTDOWN
• Countdown timer range:
99:59’59” - 0’00”00
WORLD TIME
• The time in another time zone.
PACER
• 18 pacer settings (10 - 320).

PARTNER
7
STOPWATCH
• Units in 1/100 second;
• 8 Laps, Splits;
• Measurement range:
0’00”00 - 99:59’59”.
TIMEKEEPING
TIME SETTING
1. In timekeeping mode, press and
hold “A” until the city code starts
flashing (flashing shown in setting
mode);
2. Press “C” or “D” to select the city
code; press and hold to scroll
quickly;
3. Press “B” to select Daylight Saving
Time;

8
4. Press “C” or “D” to switch Daylight
Saving Time ON/OFF.
5. Repeat step 3 and 4. The selection sequence is as follows:
City code Daylight Saving Time Seconds Hour Minutes
12/24H Format Year Month Date M-D/D-M Format Key
Tone (ON/OFF) Alarm (ON/OFF) Timer (ON/OFF) World
Time (ON/OFF) Pacer (ON/OFF);
6. Press “A” to exit setting mode when
you have finished. (The day of the
week is automatically displayed in
accordance with year, month and
date setting).
• When the key tone (BEEP) is set
to “OFF”, buttons will not make a
sound when pressed.
• Press “B” to change the mode.
The corresponding mode function
will be OFF when the alarm,
countdown, world time, or pacer
are set to “OFF”.

PARTNER
9
DIVING
SETTING DIVE PARAMETERS
1. In dive mode, press and hold “A”
until the temperature and depth
units begin flashing (flashing in
setting mode);
2. Press “C” or “D” to select Metric /
Imperial;
3. Press “B” to move to the next
selection;
4. Press “D” to increase the number
or press “C” to decrease it. Press
and hold to scroll quickly;

10
5. Repeat steps 3 and 4. The selection sequence is as follows:
Unit Safe dive depth Safe dive time (minutes, seconds);
6. Press “A” to exit the setting mode
when you have finished.
• Safe dive depth range: 0.0, 3.0 –
100 m or 0, 10 – 328 ft, default is
0.0 m or 0 ft.
• Safe dive time range: 0’00” -
59’59”; default is 0’00”.
FREE DIVING
Dive time
Surface time
1. Diving depth can be measured in
dive mode.
2. Dive time starts when the
diving depth exceeds 1.2m or 4ft
(“ “ flashing);
3. Surface time turns on when the
user exits the water;
4. Repeat steps 2 and 3. You can measure multiple times (maximum 99 dive times).