Seada G44 HDMI Instruction manual

G44 Quick Start Manual
SD-MA-026 V02
1
2
3
4
Note
1. Do not fix the device to any surface which is a heat source to avoid over heating
2. Do not cover the surface or ventilation grills of the device to avoid over heating
1. Verify the package contents
Please verify the package contents against the List Below
1. G44 Controller x1
2. Power Supplier x1
3. Software & Documentation User CD x1
4. Serial Cable x1
5. Network Cable x1
6. Remote Control x1
7. Ground Wire x1
8. Connectors
•Phoenix x8
•DVI to HDMI x2
•DVI to VGA x2
•DVI to RCA x2
2. Set up the G44
Power up the G44 controller and connect the input and outputs to correct devices.
Figure 1
3. Run the software on control PC
Users can run the G44.exe software directly without installation. G44
requires password authentication (default password for Administrator
is: 111111)
4. Connect through Serial Port
Connect the device with a serial cable. Select the COM port from the Port dropdown
menu (there should only be one COM port if you have connected the device to the
laptop). Press on the button to the right of “Status” it should switch to connected if the
unit is recognized correctly
Model: G44-DVI
1 –Display
2 –Input Buttons
3 –Output Buttons
4 –Function Buttons
Back Panel includes 4 DVI-U Inputs and Outputs,
Ethernet control port, 2x Serial ports and 4 3.5
mm captive screw connectors for audio inputs
and outputs
LCM

G44 Quick Start Manual
SD-MA-026 V02
5. Connect through Network
The default IP address for G44 controller is 192.168.0.247 Users need to change the IP address of the control PC to the
same network segment as the G44.
•Change the ‘Obtain an IP address automatically’
to ‘Use the following IP address’ to set up a static IP address of TCP/IPv4 in Ethernet Properties
 IP address: any address between 192.168.0.2 and 192.168.0.254 except the address which has been taken by the
G44
 Subnet mask: 255.255.255.0, Default Gateway: 192.168.0.1
•Once the control PC IP address having been set up, connect PC to either the RJ45 ports of G44 controllers via
a network cable and then press the Connect button to connect the device.
6. Matrix Switch Mode
Ensure the inputs are mapped to an output and verify with your screens. Changing the
input routing can be done through the software, through the front panel or through
the serial commands detailed in the manual.
6.1 Through the Software
Change the routing on the video routing matrix by
arranging the inputs on the desired outputs. Alternatively, you can change the
routing through the TV Wall tab –Right click on the screen you want to change
the input of and navigate your mouse to Input Select. This will allow you to select
one of the four inputs.
6.2 Through the Hardware
If you want to change the video routing through the front panel:
•Press the input button followed by the output you want it to be
displayed on
•This should prompt a change in the front panel display –the input
number over the output number should be underlined.
•Press Enter to complete the command.
•This should switch the input on the screen.
7. Presentation Mode
The presentation mode allows the user to route the audio input to a different output
and vice versa. This is achieved the same way as the Video Matrix Routing. The blue
area represents where the selected input/output
8. Video Wall Mode
In the TV Wall tab –select the screens you wish to combine/merge and then select screen
stitching. This will combine the selected displays and output only one input creating a
video wall effect.
This quick start guide provides basic instructions for setting up SEADA G44 video wall controllers. For additional
information about how to use the controllers, please refer to the G44 User Guide (SD-MA-027), which is available on
the CD included in this package.