Sealey TS02 User manual

1000MM FLOOR STANDING SHEET METAL
FOLDER
MODEL NO: TS02
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
TS02 Issue 2 (H) 24/10/22
Original Language Version
© Jack Sealey Limited
Wear eye
protection Wear protective
gloves
1. SAFETY
9 Wearapprovedsafetygoggles,gloves,andfootwear,whenoperatingthefolder.YourlocalSealeydealero󰀨ersacompleterangeof
safety equipment.
9Use the tool only for its intended purpose.
9Regularly check all parts of the folder for damaged parts. DO NOT use if any of its components are broken, worn or damaged.
9Use original Sealey spare parts and accessories. Use of non-recommended spare parts may be dangerous and will invalidate
warranty.
9Ensure good footing, wear non slip footwear.
8DO NOToperatethistoolwhileundertheinuenceofdrugs,alcoholorotherimpairingmedication.
8DO NOTAllowunqualiedpersonstooperatethemetalfolder.Keepchildrenawayfromthetool.
2. INTRODUCTION
 Floorstandingsheetmetalfolder,ttedwithmountingplates.Capableofbendinga1mmrod,oflimitedlength,uptoandbeyonda90°
 angle.Theuniquepatentedendlessdesignandremovablefoldingplateallowstheusertofold,channelando󰀨setanylengthofsheet
metal up to 20 Gauge thick, by simply moving the sheet as required after each fold. With adjustable fold plate to help achieve the
cleanest fold possible. Ideal for the small garage or restoration operation.
3. SPECIFICATION
MODEL NO:......................................................... TS02
Capacity:..........................20 Gauge Sheet, Ø1mm Rod
1 Top/Base plate clamp
2 Adjustment/PositioningCam
3 Removable Folding Plate
4Centre adjustment nut
5 Top Plate
6 Standing plate
7 Folding Handles
g.1
Wear safety
footwear

Original Language Version
© Jack Sealey Limited
4. OPERATION
4.1. Unpack the unit and check that all parts are included and not damaged. Should you experience a problem contact your
supplier immediately.
4.2.  Positionfolderwhereitistobemounted,ensuringthatthehandlesg.1.7hangverticallyoverthefrontofthe  
oorspacesoascanbeusedwithoutobstruction,useplatestosteadyduringuseg.1.6.    
4.3.  Byusingcentreadjustmentnutg.1.4ensuretopandbaseplateareparallel,thismayrequireadjustmentfromtimetotime.
4.4.  Releaseclampsg.1.1ateitherendoffoldersothatasmalltestpieceofsheetmetalcanbeinsertedbetweenthetopandbase
 plates.g.1.3
4.5.  Positionthetestpiece,adjustthetopplatebyuseofclampsg.1.1lightlytighten,useaspannertoadjustcamg1.2,sothat 
base and top plate are aligned.
4.6. Ensure that there is even pressure on both ends.
4.7.  Raisethetopfoldingplateg.1.3byliftinghandlestocreatethefold.Fromthistest,youwillbeabletodeterminehowandwhere
 thefoldappears.Whensatisedwiththetestresults,proceedwiththeactualworkpiece.
4.8. By rotating the end clamps through the vertical axis, longer lengths of metal sheet can be folded, i.e. fold a section, unclamp, move
sheet, reclamp, fold second section etc.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste.All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations. REGISTER YOUR
PURCHASE HERE
TS02 Issue 2 (H) 24/10/22