1. SAFETY
1.1. GENERAL SAFETY
9Disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.
9Maintain grinder and discs in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
WARNING! Always work with the grinder’s safety guard in place.
9Wear approved safety goggles, ear defenders, gloves and, if grinder generates dust, a dust mask.
9Position the power cable clear of the grinding wheel to avoid cutting or snagging it. Hold grinder only by insulated gripping surfaces.
9 Removeillttingclothing.Removeties,watches,ringsandotherloosejewelleryandcontainlonghair.
9Use grinder in a suitable work area. Keep area clean, tidy and free from unrelated materials and ensure adequate lighting.
9Maintain correct balance and footing, DO NOTover-reach.Ensuretheoorisnotslipperyandwearnon-slipshoes.
9Use only approved grinding discs and only use the normal grinding surface.
9Check grinding disc to ensure there are no splits, cracks or other damage (see Section 6). If in doubt DO NOT use the disc.
9Grinding discs must be securely attached before use, but not over-tightened.
9Secure unstable workpiece with a clamp, vice or other adequate holding device and ensure the grinder is gripped with both hands.
9Keep non-essential persons away from the working area, use screens if necessary.
8DO NOT operate the grinder if any parts are missing or the grinder is damaged.
8DO NOT use the grinder for a task it is not designed to perform.
8DO NOToperatethegrinderwherethereareammablesolids,liquidsorgasses.
WARNING! DO NOT grind any materials containing asbestos.
8DO NOT get the grinder wet or use in damp or wet locations.
8DO NOT switch the grinder on whilst the disc is in contact with the workpiece.
8DO NOT cover the grinder air vents. To do so will overheat the machine.
8DO NOT touch the workpiece immediately after grinding, it will be very hot.
8DO NOTusethegrinderasaxedtoolandDO NOT try to cool the grinding disc with water or other lubricants.
8DO NOT touch the grinding disc whilst operating, or whilst plugged into the mains power.
8DO NOT leave the grinder running unattended, and DO NOT lay the grinder down whilst it is running.
8DO NOToperatethegrinderwhenyouaretiredorundertheinuenceofalcohol,drugsorintoxicatingmedication.
9 Whennotinuseswitchogrinder,removeplugfrompowersupplyandstoreinsafe,dry,childproofarea.
9Use only approved grinding discs and only use the normal grinding surface. Never use the side or upper surface of disc for cutting.
9 Thegrindingdiscmayonlybechangedbyapersonholdingagrindingwheelcerticate.
9Grinding discs must be securely attached before use, but not overtightened.
2. INTRODUCTION
Compact, lightweight cordless mini angle grinder. Comfortable composite housing with soft grip to reduce vibration. Brushless motor allows
for a longer lasting tool requiring less maintenance. Spindle lock for easy disc changes. Built-in battery charge level indicator. Cutting disc not
included.
Danger of re/explosion hazard
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition, especially when
grinding metal.
8DO NOTusethegrinderwherethereareammableliquids,solidsorgases.
8DO NOT allow grinder sparks to make contact with the operator’s clothing or any other fabric such as cleaning rags. Fabrics
contaminatedwithammablematerialssuchaspetrol,oil,grease,paintandsolventsareaparticularrehazard.
9 Toreducetheriskofclothingcatchingretheoperatorshouldwearwoolorcottonoutergarmentstreatedwithareretardantin
preferencetoman-madebres.
12V Ø76MM ANGLE GRINDER - BODY ONLY
MODEL NO: CP1210
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
CP1210 Issue 1 16/07/2020
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
Wear a mask Wear
respiratory mask
(fumes)
