Sealey CP108VMTBO User manual

10.8V SV10.8 SERIES MULTI-TOOL - BODY
ONLY
MODEL NO: CP108VMTBO
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Disconnect the multi-tool from the battery unit before changing accessories, servicing, storing or performing any
maintenance.
9Maintain the multi-tool and battery in good condition. Check moving parts alignment on a regular basis.
9Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9 Ensurethemulti-toolisswitchedo󰀨beforeinstallingthebatterypackorpickingupthetool.
9Remove any adjusting key or wrench before turning the tool on.
9Keep the multi-tool and charger clean for best and safest performance.
9Keep working area well lit.
9 Removeillttingclothing.Removeties,watches,ringsandotherloosejewelleryandcontainlonghair.
9 Evaluateyourworkingareabeforeusingthemulti-toole.g.ceilings,oorsandenclosuresmaycontainelectricalitemsorwaterpiping.
9Ensure battery pack is correctly inserted into the tool handle and latched in place before attempting to switch it on.
9Secure loose work pieces with a clamp, vice or other adequate holding device.
9Avoid unintentional starting.
9Wear approved safety eye and ear protection (standard spectacles are not adequate). Wear a mask.
8DO NOToverreach.Maintaincorrectbalanceandfooting.Ensuretheoorisnotslipperyandwearnon-skidshoes.
8DO NOT let familiarity from frequent use of tool allow you to become complacent and ignore tool safety principles.
9Keep children and unauthorised persons away from the working area.
9Keep tool and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
8DO NOTusethetoolwherethereareammableliquids,solidsorgases,suchaspaintsolvents,etc.
8DO NOT allow children to operate the tool. DO NOT allow persons unfamiliar with the tool or these instructions to operate the tool.
8DO NOT operate the tool if any parts are missing as this may cause failure and/or personal injury.
8DO NOT hold unsecured work piece in your hand.
8DO NOT leave the tool operating unattended.
8DO NOTcarrythetoolwithyourngeronthepowerswitch.
8DO NOT use the tool for a task it is not designed to perform.
8DO NOT force the tool. Use the correct tool for your application. The correct power tool will do the job better and safer and at the rate
for which it was designed.
9Use the power tool in accordance with these instructions, taking into account the working conditions and the work to be performed.
 Useofthetoolforoperationsdi󰀨erentfromthoseintendedcouldresultinahazardoussituation.
9Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected situations.
8DO NOTusethetooliftheswitchdoesnotturnito󰀨andon.Anypowertoolthatcannotbecontrolledwiththeswitchisdangerousand
must be repaired.
8DO NOToperatethetoolwhenyouaretiredorundertheinuenceofalcohol,drugsorintoxicatingmedication.
8DO NOT get the tool or battery charger wet or use in damp or wet locations.
2. i INTRODUCTION
Part of the SV10.8 Series offering a one battery fits all solution, keeping costs down without compromising on performance. Compact,
lightweight cordless Multi-Tool - Body Only. Comfortable housing with soft grip to help reduce vibration. One tool suitable for multiple
tasks such as sanding, scraping and cutting various materials. Includes sanding paper, backing pad, scraper and cutting blade. 6-Speed
settings for greater control. Quick release/lock system for fitting attachments. Requires compatible 10.8V 2Ah or 4Ah battery and mains
charger, sold separately.
CP108VMTBO Issue 1 02/12/22
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection Wear a mask Wear ear protection Wear protective gloves

3. i SPECIFICATION
Model No: ......................................................CP108VMTBO
Noise Power...................................................................84dB
Noise Pressure ..............................................................73dB
No Load Speed:.......................................5000 - 18000 OPM
Vibration.................................................................0.571m/s2
Uncertainty.................................................................1.5m/s2
Battery: ...............10.8V 2Ah - 4Ah Lithium-ion (not included)
Consumable parts
CP108VBP - 2Ah Battery, CP108VBP4 - 4Ah Battery.
Replacement parts
Mains charger..................................................... CP108VMC
Accessories:
Sanding Paper .........................................................SMTA11
Backing Pad............................................................. SMTA12
Scraper .................................................................................
Cutting Blade .........................................................................
4. OPERATION
WARNING: Removebatterybeforettingtoolormaintenanceiscarriedout.
4.1. To remove the battery from the equipment, depress the spring loaded button on the battery pack. Remove the battery pack by sliding
out. DO NOT touch the metal battery terminals.
4.2. USING THE TOOL (FIG.1)
4.2.1. Ensure that you have read, understood and comply with all the safety instructions in Section 1.
4.2.2. Removebatteryfromtool.Depresstabonfrontfaceofbatteryandslidebatteryo󰀨thetool.
4.2.3. To fit the required accessory tool bit lift the quick release handle (fig.1).
4.2.4. Unscrew the locking collar from the drive shaft (fig.2).
4.2.5. Locate the accessory tool onto the drive shaft spigots and refit locking collar until tight.
4.2.6. Close quick release handle and confirm firm attachment of accessory tool.
4.2.7. Refit battery and, ensuring that the speed controller is set to speed 1 (fig.2), slide the On/Off switch to On position.
4.2.8. Select appropriate tool speed for the task in hand.
4.2.9. When finished, remove the tool bit, clean the tool and tool bit and store in a cool, dry place out of the reach of children.
5. MAINTENANCE
WARNING: Always disconnect from power source before carrying out any inspection, maintenance or cleaning.
5.1. GENERAL INSPECTION
5.1.1. Regularlycheckthatallthexingscrewsaretight. 
5.1.2. Repairs should be carried out by an authorised service centre.
5.2. CLEANING
WARNING: Always wear protective equipment including eye protection and gloves when cleaning this tool.
5.2.1. Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device’s service life.
5.2.2. Clean the body of your machine with a soft brush, or dry cloth.
5.2.3. Neverusecausticagentstocleanplasticparts.Ifdrycleaningisnotsu󰀩cient,amilddetergentonadampclothisrecommended.
5.2.4. Water must never come into contact with the tool. Ensure the tool is thoroughly dry before using it.
5.2.5. If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
5.3. LUBRICATION
5.3.1. Lightly lubricate all moving parts at regular intervals with a suitable spray lubricant.
5.4. BRUSHES
5.4.1. Over time the carbon brushes inside the motor may become worn
5.4.2. Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking.
5.4.3. If you suspect that the brushes may be worn, have them replaced at an authorised service centre.
5.5. STORAGE
5.5.1. Store this tool carefully in a secure, dry place out of the reach of children.
Original Language Version
© Jack Sealey Limited CP108VMTBO Issue 1 02/12/22
fig.1fig.2

WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 0.571m/s²
Uncertainty value (k): 1.5m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a
specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be modified
accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and
Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSC website
www.hse.gov.uk - Hand-Arm Vibration at Work.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
© Jack Sealey Limited
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
CP108VMTBO Issue 1 02/12/22