SECO-LARM ENFORCER MVD-AH12-01Q User manual

4K HDMI Splitters
Installation Manual
MVD-AH14-01Q shown
Model Type
MVD-AH12-01Q 4K 1x2 HDMI Splitter
MVD-AH14-01Q 4K 1x4 HDMI Splitter
The ENF RCER 4K HDMI Splitters allow for one HDMI source to simultaneously transmit to up to
four different monitors. The splitters work with most HDMI devices, delivering the very best in
digital audio and video signals with HD resolutions of up to 4K@60Hz. An LED indicator clearly
displays power status as well as which outputs are active. The 4K HDMI Splitters can be daisy-
chained up to four levels for even more outputs.
•Transmits an HDMI source to up to two (MVD-AH12-01Q) or four (MVD-AH14-01Q) different
HDMI displays
•Additional splitters can be daisy-chained for more outputs
•HDR Support
•Supports up to 4K@60Hz resolution and 3D video
•Individual status LEDs for each HDMI output
•Two EDID management settings
•ne 5VDC power supply included
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

4K HDMI Splitters
2 SECO-LARM U.S.A., Inc.
1x2 HDMI Splitter
POWER IN CH1 CH2
EDID
1080P/TV
CH1 CH2 5VDC
HDMI OUTPUT HDMI INPUT
5
/
8
"
(16 mm)
Parts List
1x
4K HDMI Splitter
1x
5VDC Power supply
1x
M nu l
Specifications
Model MVD-AH12-01Q MVD-AH14-01Q
Type 4K HDMI Splitter
M ximum single link r nge 4K*2K@60Hz
Deep color 24bit RBG/YCBCR 4:4:4
Video form ts supported HDMI 2.0b, HDCP 2.2
Audio form ts supported LPCM 7.1 CH Dolby TrueHD, DTS-HD Master Audio
Output video HDMI
HDR support Yes
Resolutions supported 4K/1080p/1080i/720p/576p/576i/480p/480i
Video mplifier b ndwidth 600MHz/18Gbps
Video input connector 1x HDMI Type A 19-pin female
M x. input c ble length 24AWG: 50' (15m); 26AWG: 30' (10m); 28AWG: 16' (5m)
Video output connector 2x HDMI Type A 19-pin female 4x HDMI Type A 19-pin female
M x. output c ble length 24AWG: 50' (15m); 26AWG: 32' (10m); 28AWG: 16' (5m)
Oper ting volt ge 5VDC
Power supply 1A@5VDC (2.1mm plug)
ESD protection ±8kV (air-gap discharge), ±4kV (contact discharge)
Current dr w 2W
Oper ting temper ture 32°~104° F (0°~40° C)
Oper ting humidity 20~90% RH (no condensation)
Dimensions 23/16"x315/16"x5/8"
(56x100x16 mm)
21/2"x67/16"x5/8"
(63x163x16 mm)
Weight 6-oz (165g) 9-oz (260g)
Overview
MVD-AH12-01Q
3
15
/
16
" (100 mm)
2
3
/
16
"
(56 mm)

4K HDMI Splitters
SECO-LARM U.S.A., Inc. 3
1x4 HDMI Splitter
HDMI OUTPUT HDMI INPUT
CH2CH1 CH3 CH4 5VDC
IN CH1 CH2 CH3 CH4 SERVICE
EDID
1080P/TVPOWER
MVD-AH14-01Q
Overview (Continued)
Installation
1. Determine the location of where the 4K HDMI Splitter will be installed in relation to the HDMI
source and HDMI displays.
2. Plug the HDMI source into the HDMI connector input on the splitter.
3. Plug the HDMI displays into the HDMI connector outputs on the splitter.
4. Plug the 5VDC adapter into the splitter.
5. Turn the HDMI source and displays on.
6. Adjust the EDID settings as necessary
EDID Management Settings
TV – Copy the display resolution from utput 1 to other utput displays.
1080p – Limit the resolution to 1080p.
5
/
8
"
(16 mm)
6
7
/
16
" (163 mm)
2
1
/
2
"
(63 mm)

4K HDMI Splitters
1x4 HDMI Splitter
Sample Application
Troubleshooting
HDMI Device does not
function correctly.
•Make sure the splitter is powered.
•Make sure the source and display(s) are powered.
•Make sure that there are no problems with the HDMI source, HDMI
cables, or HDMI display(s) by plugging a source directly into the display
using the HDMI cables.
•Make sure that the source and display(s) are plugged into the correct
connectors.
•Make sure the HDMI source is compatible with the HDMI display(s).
•Make sure the HDMI input and output cables are used within the specified
range (see Specifications).
SECO-LARM ®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PICHN3
MI_MVD_AH1x
-
01Q_211125.docx
WARRANTY: This SEC -LARM product is warranted against defects in material and workmanship while used in normal service for one (1)
year from the date of sale
to the original customer. SEC -LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepa
id, to
SEC -LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alterati
on, improper
or abnormal usage, or faulty installation, or if for any other reason SEC -LARM determines that such equipment is not
operating properly as a result of causes other
than defects in material and workmanship. The sole obligation of SEC -
LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair
only, at SEC -LARM’s option. In no event shall SEC -
LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind
to the purchaser or anyone else.
NOTICE: The SEC -LARM policy is one of continual development and improvement. For that reason, SEC -
LARM reserves the right to change specifications without
notice. SEC -LARM is also not responsible for misprints. All trademarks are the property of SEC -LARM U.S.A., Inc. or their respective owners. Copyright © 2022
SEC -LARM U.S.A., Inc. All rights reserved.
C liforni Proposition 65 W rning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information, go to www.P65Warnings.ca.gov.
IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product comp
lies with all national, state,
and local laws and codes. SEC -LARM will not be held responsible for the use of this product in violation of any current laws or codes.
HDMI, the HDMI Logo and High-
Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
FCC COMPLIANCE STATEMENT
THIS DEVICE C MPLIES WITH PART 15 F THE FCC RULES. PERATI N IS SUBJECT T THE F LL WING TW C NDITI NS: (1)
THIS DEVICE MAY
N T CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED PERATI N.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMP RTANT N TE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitt
ed. Any change to the antenna
or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
MVD-AH14-01Q
C ble Legend
HDMI
Power
5VDC
Power Supply
HDMI Source
HDMI
Display
HDMI
Display
HDMI
Display
HDMI
Display