SECO-LARM Enforcer EV-7105-NPEQ User manual

Note: Model numbers thatend with “Q” or products that have a round green “Q” sticker signify RoHS compliance.
EV-7105-NPEQ (NTSC)
EV-7105-PPEQ (PAL)
Mini PTZ Camera
Manual
•
10x Optical zoom and 10x digital zoom
•Up to 100x zoom
•Up to 360°/sec pan/tilt motion
•Outdoor or indoor use
•
Up to 127 preset target views, each
with its own characteristics such as
white balance and auto exposure
•Up to 95° tilt, up to 180° with auto-flip

2
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
a
Table of Contents
Introduction
The EV-7105-NPE is a full-featured PTZ (pan/tilt/zoom)CCTV camera which can pan a full 360 degreesin as
little as a second or tiltup to 95degreesunder normaloperation oras much as180degreesusing auto-flip. It
also featuresan optical zoom of up to 10Xand a digital zoomof up to 10X, providinga clear view ofthe entire
protected premises. The 1/4inch Interline Transfer CCD provideshigh-resolution,500TV line images in as little
as 0.7 Luxfor color use and 0.02 Lux for black and whiteuse. A wide range of mountingbrackets andposts
combined with the smallsize of the EV-7105-NPE make it an ideal PTZ camera for almost any installation.
Control of the EV-7105-NPE isdone via a keyboard controller orDVRwhich uses Pelco protocolsfor
communicating between thedevices. Non-Pelco-compatible devices willmost likely not be able to operate the
EV-7105-NPE properly.
Introduction 2 SYSTEM INFORMATIONMenu 18
Features and Functions 3 DISPLAY SETUP Menu 19
Parts List 4 SET NORTH DIRECTION Menu 19
Specifications 4 PRIVACY ZONE Menu 20
Dimensions 5 EDIT MASK Menu 20
Safeguardsand Precautions 6 DOME CAMERA SETUP Menu 21
Overview 7 ZOOM CAMERA SETUPMenu 22
CommunicationProtocol and Camera ID 8 WB SETUP Menu (WhiteBalance) 22
Installation 9 AE SETUP Menu (Auto Exposure) 23
ConnectingMultiple PTZCameras 9 MOTION SETUP Menu 24
Pre-Operation Checklist 10 PARKING ACTION SETUP Menu 25
Understandingand Operating Preset and
Pattern Functions 11 PRESETMenu 26
ConfiguringMiniPTZ settings using an
ENFORCERDR-1 Series DVR
12 EDIT SCENE Menu 27
Reserved Presets 13 EDITLABEL Menu 27
Configuration Defaults 13 SWING SETUP Menu 28
OSD Display ofMain Screen 14 PATTERN SETUPMenu 29
OSD Main Screen 14 EDITPATTERN Menu 29
Operating the OSD Menus 15 GROUP SETUP Menu 30
OSD (On-Screen Display) and
Programming Flowchart
16-17 EDIT GROUP Menu 30-31
SPEED DOMECAMERAMenu 18 SYSTEM INITIALIZE Menu 31
Introduction
The ENFORCER Mini PTZ Camera is a compactfull-featured PTZ (pan/tilt/zoom) CCTV camera. In as little asone second,
the camera can pan a full 360 degrees, tilt up to 95 degrees under normal operation,or auto-flip 180 degrees. It also
featuresan optical zoomof up to 10X and a digitalzoom ofup to 10X,providing a clear viewof the entireprotected
premises. The 1/4-inch Interline TransferCCD provides high-resolution,520 TV line imagesinas little as 0.7 Lux
for color use
and 0.02 Lux for black and white use. A wide range ofmounting brackets and postscombined with a small size makes the
ENFORCER Mini PTZ Camera ideal for almost any installation.
Controlling the mini PTZ camera is done using a keyboard controller or DVR thatuses RS-485 for communicating between
the devices.
Table of Contents

3
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
EV-7105-NPE PTZ Camera Features and Functions
Powerful yet flexible camera: 1/4-inch CCD camera with Day and Nightfunction, up to 100X zoom (max. 10X
optical zoom and 10X digital zoom), multiple focusmodes, and full programmability.
Powerful Pan/Tilt functionality: The camera features360-degree panmotion,and it can be programmed to
automaticallyflip the image if it tilts underthe unit. The pan/tilt function uses vector drive technology so that it
quickly moves to the target while ensuringthe viewon the monitorflows smoothly.
On-Screen Display (OSD) programming: The On-ScreenDisplayshows camera status and settings together
with the preset target views.
Flexible programming capabilities:
•Up to 127 preset target views, each with its own characteristics such as white balance and auto exposure.
•Up toeightswing actionsbetween two preset positions.
•Up to four patterns formoving the camera as if it were controlled bya joystick.
•Up toeightgroup actions,each including up toa total of 20presets,swing actions, and patterns.
•Up to four privacy masks which can be increased ordecreased in size to cover certain areas to
protect privacy.
Reserved presets: Certain camera characteristics can be specified byusing reserved preset configurations
instead of individually configuring those characteristics.
Standard PTZ control: Works with Pelco-D or Pelco-P compatible controllersvia an RS-485 cable.
Power Up Action: Resumes the lastaction executed before power to the camera was cut, including most
preset, pattern, swing, and group actions, but not jog actions.
Auto Flip: Vertically inverts the image ifthe camera tilts
Parking Action: Should no operator-activated or automated camera actionoccur during a specified time
(programmable from 1 minute to 4hours), the cameraautomatically movesto apre-determined preset position.
Privacy Zone Mask: Up to four privacy masks can be created to cover certain areas or objects such as
windowsor private houses. The masks can be adjusted for size. When the camera moves past such areas or
objects, the mask automatically follows them.
Global or Local Image Setup: Determines how white balance and auto exposuresettingsareapplied. When
programmed for "Global" setup,those settings areautomaticallyapplied to each presetlocation.Under"Local"
setup, those settings are set separately for each preset location.The "Global" settings for whitebalance and
auto exposure will beused during jog operations.
Semi/Auto Focus: The focus for each preset location is manuallyset, and the camera automatically uses that
focus when it moves to a presetlocation.During job operations, the camera usesauto focus. The shift between
semi and auto focus occurs automatically.
ENFORCER Mini PTZ Camera Features and Functions
Powerful and Flexible: The ENFORCER Mini PTZ Camera is equipped with a 1/4-inch CCD, apowerful Day and Night
function,up to 100x zoom (max. 10x optical zoom and 10x digital zoom), multiple focus modes, and otherfull
y programmable
features.
Pan/Tilt Functionality: The camera features 360° endless panmotionand 95° tilt. It can be programmed to automatically
flip the image if it tilts under the unit. The pan/tilt function uses vector drive technology so that it quicklymoves to the target
whileensuring the view on the monitor flows smoothly.
On-Screen Display (OSD): The On-ScreenDisplays
hows camera status and settings together with the preset target views.
A Wide Rangeof Programmable Options:
•Up to127 preset target views, each with its own characteristics such as white balance and auto exposure
•Up toeightswing actionsbetween two preset positions
•Up to four patterns formoving the camera as if it were controlled bya joystick
•Up toeightgroup actions,each includingup to a totalof 20 presets, swing actions, and patterns
•Up to four privacy masks which can be increased ordecreased in size to cover certain areas to
protect privacy
Reserved Presets: Certain camera characteristics can be specified by using reserved preset configurationsinstead of
individually configuring those characteristics.
Standard PTZ Control: Works with Pelco-D or Pelco-P compatible controllersvia anRS-485 connection.
Smart Power-Up: Resumes the last action executed before power to the camera was cut, including most preset, pattern,
swing, and group actions.
Auto-Flip: Verticallyinverts the image if the camera tilts belowitscenter.
Parking Action: Should no operator-activated or automated camera actionoccur during a specified time (programmable
from1 minute to 4 hours), the cameraautomatically movesto a pre-determined preset position or any pre-programmed
pattern, swing, or automaticcamera function.
Privacy Zone Mask: Up to four privacy masks can be created to cover certain areas or objects such aswindowsor private
houses. The masks can be adjusted for size. When the cameramovespast such areas or objects,the maskautomatically
coversthem.
Global or Local Image Setup
: Determines how white balance and autoexposure settings are applied.When programmed
for "Global" setup, those settings are automatically applied to eachpreset location.Under"Local" setup, those settingsare
setseparately for each preset location.The "Global" settings for white balance and auto exposure will beused during jog
operations.
Semi/Auto Focus
: The focus for each preset location is manuallyset, and the camera automatically usesthat focus when it
moves to a preset location. During jogoperations, the camera uses auto focus.Theshift between semi-auto and auto focus
occurs automatically.

4
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
a
Video Signal System
NTSC
PAL
Camera
CCD
1
/4” Interline Tansfer CCD
Max. Pixels
811(H) x 508(V) 410K
795(H) x 596(V) 470K
Effective Pixels
768(H) x 494(V) 380K
752(H) x 582(V) 440K
Horizontal Resolution
500 TV Lines (Color),570 TV Lines (B/W)
S/N Ration
50 dB (AGC Off)
Zoom
x 10 Optical Zoom,x 10 Digital Zoom
FocalLength
F1.8, f=3.8~38 mm
Min. Illumination
0.7 Lux (Color) / 0.02 Lux (B/W), 50 IRE
Day and Night
Auto / Day / Night (ICR)
Focus
Auto / Manual /SemiAuto
Iris
Auto / Manual
Shutter Speed
X128 ~1/120000sec
AGC
Normal / High / Off
White Balance
Auto /Manual (Red/Blue Gain Adjustable)
BLC
Low / Middle / High / Off
Flickerless
Selectable
SSNR
Low / Middle / High / Off
Pan/Tilt
Range
Pan: 360 degrees / second
Tilt: 180 degrees(Auto-Flip), 95 degrees (Normal)
Pan / Tilt Speed
Preset: 360 degrees / second
Manual: 0.05~360 degrees /second (proportional to zoom)
Swing: 1~180 degrees / second
Preset
127 Preset (Label, Camera Image Setting)
Pattern
4 Pattern, 1200 commands (about 5 minutes) / pattern
Swing
8 Swing
Group
8 Group (20 action entities /group)
OtherFunctions
Auto-Flip, Auto-Parking, Power Up Action, etc.
General
Communication
RS-485
Protocol
Pelco-D, Pelco-P selectable
Privacy Zone
4 Zone
Alarm Input
4 Input
OSD
Menu / PTZ Information, etc.
Rated Power
DC12V 2A
Dimension
Dome: ф100.5
Housing: ф141 x 140 (H) mm
Weight
About1.2 Kg
Operating Temp.
0-40 degrees C (Indoor) -20-50degreesC (Outdoor)
a
Range
Pan
360°
Tilt
180°
Pan/Tilt
Speed
Preset
Up to360°/s (programmable)
Manual
0.05~360°/s (proportional to zoom)
Swing
1~180°/s
Presets
Max. 127 presets (Label, Camera Image Setting)
Patterns
Max. 4 patterns
Swings
Max. 8 swings
Groups
Max. 8 groups (20 actions/group)
Other functions
Auto-Flip, Auto-Parking, Power Up Action, etc.
Pan/Tilt:
Parts List:
1xCamera
1xWall-mount bracket
1xManual
4x Short screws (for attaching camera to bracket)
4x Long screws (for attaching bracket to wall)
1x Extension cord
EV-7105-NPEQ
EV-7105-PPEQ
Type
Mini PTZ Camera
Video output format
NTSC
PAL
CCD
1
/
4
” Interline Transfer
Resolution
Color: 520 TV Lines / B/W: 570 TV Lines
Pickup elements
768x494 pixels
752x582 pixels
Video output
1.0Vp-p composite video, 75Ω
Lens
F1.8, f=3.8~38mm
Minimum Illumination
Color: 0.7 Lux / B/W: 0.02 Lux
S/N Ratio
50dB (AGCOFF)
Zoom
x10 Optical /x10 Digital
Day and Night
Auto / Day / Night (ICR – removable IR cut filter)
Focus
Auto / Manual / Semi-Auto
Iris
Auto / Manual
Shutter Speed
1/60~1/120,000 s
AGC (Automatic Gain Control)
Normal / High / Off
Sense-Up
x2~x128
White Balance
Auto / Manual (Red, Blue, Gain Adjustable)
BLC (Back Light Compensation)
Low / Middle / High / Off
Flickerless
Selectable
SSNR (Noise Reduction)
Low / Middle / High / Off
Communication
RS-485
Protocol
Pelco-D, Pelco-P selectable
Privacy
4 Zones
OSD
Menu / PTZ information, etc.
Operating voltage
24VAC
Power consumption
20W
Operating temperature
Indoor: 32~104° F (0~40° C) /
Outdoor: -4~122° F (-20~50° C)
Dimensions
4
13
/
16
” x7”x4
13
/
16
” (122x180x122 mm)
Weight
2-lb 10-oz (1.2kg)
Specifications:

5
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
Dimensions:
Camera
Wall-Mount Bracket
7”
(180mm)
6”
(152mm)
3
1
/
8
”
(80mm)
4
11
/
16
”
(119mm)
6
1
/
2
”
(166mm)
Side
Bottom
Side
Bottom
413/
16
”
(122mm)

6
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
Safeguards and Precautions
Before Starting:
1. Please read this manualcarefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do notpointthe camera at the sun. Heat could damage the camera,even when not in use.
4. Do notexpose the camera to rain or moisture.
5. Do notinstall the camera in dustyor humid environments.
6. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
7. Do notopen ordisassemble the camera.Thereare no field-serviceable parts inside.
8. Do not drop the camera or subject it to strong vibrations.
9. Thiscamera isVERY HEAVY. To preventinjuryto the installer and client, do not mountit on an unstable or improperly
supported surface. When mounting, only use brackets or other mountingdevicesthat are recommended in this manual.
Operation Precautions:
1. Onlyuse regulated powersupplieswith voltage and minimum currentoutput per the specificationsof this camera.
2. If the camera gets hot or starts smoking while in use, disconnect the power immediately and contact the professional
installer or dealer.
Cleaning Precautions:
1. Periodically clean the dustoff the entire camera with a slightly damp (NOT WET) cloth. DO NOT USE
chemical cleaners.
2. Do notmove the camera while cleaning, as thiscould change the angle ofthe view.
3. If the dome cover becomesdusty,carefullyclean using a slightly slightly damp (NOT WET)cloth.DO NOT USE
chemical cleaners. DO NOT SCRATCH the dome, as this will hurt thequality of the video image.

7
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
a
Wall mount
bracket
Camera
DIP switches
Lens
Dome
Turn counter-clockwise
to remove
Overview

8
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
Communication Protocol and Camera ID DIP Switch Setup:
Before the Mini PTZ Camera isinstalled,first setup the DIP switches to configure the camera ID and the
communications protocol.
a
Communication Protocol
Camera ID
On
Value
On
Value
1
2
3
4
5
6
7
8
1
2
4
8
16
32
64
128
1
2
3
4
5
6
7
8
1
2
4
8
16
32
64
128
2
+
8
=
10
Example: Camera ID=5
Example: Camera ID=10
4. Set the communication protocol
(4- pin DIP switch):
–Set the proper protocol using Pin 1 and
Pin 2 of the 4-pin DIP switch.
–The protocol for the camera mustbe
identical to theprotocol used by the DVR
or pan/tilt controller. If not, the camera
cannot be controlled by the controller. See
the DVRor pan/tilt controller
manual for protocol information.
–If the protocol of the camera is changed,
the camera must be turned off and then
turned backon for the change to take
effect.
–The factory default protocol is
"Pelco-D, 2400 bps."
–Pins3 and 4 are set bythe factory and
must notbe changed. If they
are changed,
the camera WILL NOT OPERATE
PROPERLY.
1
+
4
=
5
1. Remove the cleardome of the MiniPTZ Camera by turning it counterclockwise by hand.
2. Look forthe two DIP switch blocks
near the base of the black plastic dome whichsurrounds the camera. DO
NOT REMOVE THE BLACK PLASTIC DOME.
3. Set the camera ID (8- pin DIP switch):
–The camera ID is a binary number from 1to 255. Factorydefault camera ID is "1."
–Do not use "00000000" as a camera ID.
–The ID number of a particular camera must match the Cam ID setting of the DVR or keyboard controller.
DO NOT TOUCH
PINS 3 AND 4

9
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
a
Installation
1. Connect the camera to either the included wall mount or other optional bracket.
2. Run a24VAC powersupplywire,a video cable with amale BNC connector, and adata wire throughthe
wall to where the camera isto be mounted.
3. Connect the camera'svideo cable to the video cable coming from the wall. Do not cut the female BNC
connector ofthe camera's video cable as that will void the warranty.
4. Connect the camera's RS-485 cable to the data wire cable coming from thewall.
Note: If necessary, use the included extension cable for more convenient wiring.
5. Temporarilyconnect the camera to the powersupply. Do not cut the AC power terminalof the
camera's power cable as that will void the warranty.
6. Hold the camera's bracket againstthe wall or ceiling where it is
expected to be mounted, but do not mount
yet. While watching the monitor,operate the camera's pan and tilt functionstoensure thatthis mounting
location iscorrect. Use a pencilto mark the location of the screw holes in the mounting bracket.
7. Disconnect the power supply from the camera.
8. Mountthe mounting bracket to the wallor ceilingusing the included mounting screws. If the wall is made
of drywall, brick, or similar material, it may be necessary to use the included screwanchors.
9. Reconnect the camera's power supply.
10. Program the camera via the on-screen display (OSD) menus from the DVR or keyboard controller.
11. Do a final test of the video camera and monitor.
DR-1SeriesDVR
Connecting Multiple PTZ Cameras
Basic Installation
24VAC Jack
Video coaxial cable
RS-485 (-) (Yellow)
RS-485 (+) (Orange)

10
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
a
Pre-operation Checklist
Before operating this PTZ camera,please note the following:
Double-checkthat the cables are properly run between the controller and camera, and that all connectionsare
correct.
Double-checkthat the camera ID on the controller isthe same asthe ID ofthe target camera. The camera ID can
be foundby looking at the camera IDDIP switch settings (see page 8).
The Pelco protocol setting of the controller and the camera must be identical. The Pelco protocol setting of the
camera can be found bylooking at the communication protocolsetup DIP switch settings(see page 8).
Make sure that the camera was rebooted after anyof the camera ID or communicationprotocol setup DIP
switches are changed.
Refer to the controlleror DVR manual forinformation on configuring oroperating those devices.

11
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
Understanding and Operating Preset and Pattern Functions
Standard Pelco-compatible c
ontrollersallow the cameraoperator to do severalfunctionswithoutgoing through
the full OSD menu, dependingon the capabilitiesof the DVR to which the camera is connected.
The SECO-LARM series ofDVRsallowsoperators to do the following via the "Dome Preset" menu:
•Set the camera to remember multiple specificpreset locations.
•Tell the camera togo to a specific presetlocation.
•Run certain preset functions, including patterns, swings, or grouped functions.
•Change certain configuration patterns.
Programming the patterns, swings, or grouped functions, and detailed configuration of the PTZ camera,
requiresoperators to use the OSDmenu.See page 16 for more information.
ThisPTZ camera can be controlled byany DVR or keyboard controller which uses Pelco-compatible protocols.
Whenusingnon-SECO-
LARM DVRs, orwhen using keyboard controllers, themanuals for those devices may
include information on how to operate or program the PTZ camera.
To setor go to a Preset location or use a preset function via a SECO-LARMDVR:
1.
Press the "Dome" key.The lower leftcorner of the screen will change from"REC" to "DOME" to show the
camera is in the Dome Controlmenu.
2. Press the "1" keyto go to the DOME PRESETmenu.
3. Use the UP, DOWN, LEFT, and RIGHT buttonsto highlight your selection and push ENTER to confirm
your selection.
Note:In most cases, only the GO function will work. Only the preset locations canbe programmed via
the DOME PRESET menu. Other functionsmust be programmedusing theOSD menu.
4. Use the UPand DOWN arrowsto switch between YES and NO.Go to YES,and press the ENTER key.
See page 13 for a list of preset functions.

12
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
Configuring Mini PTZ Camera settings with an ENFORCER DR-1 Series DVR
Step 1
Press Dome on the DVR front panel to access
DVR controls.
Step 2
Press 1to access the DVR preset menu
Step 3
Use the Up, Down, Left, Right, and Enter
buttons to make a selection.
Step 4
Go to Preset 95 to access Mini PTZ OSD settings.
This will bring up the SPEED DOME CAMERA menu as shown on page 18.

13
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
<Go Preset> [95]
:Enters into OSD menu
<Go Preset> [131~134]
:Runs Pattern Function 1~4
<Go Preset> [141~148]
:RunsSwingFunction1~8
<Go Preset> [151~158]
:Runs Group Function 1~8
<Go Preset> [170]
:SetsCamera BLC mode toOFF
<Go Preset> [171]
:SetsCamera BLC mode toON
<Go Preset> [174]
:SetsCamera Focus mode to AUTO
<Go Preset> [175]
:SetsCamera Focus mode to MANUAL
<Go Preset> [176]
:SetsCamera Focus mode to
SEMI-AUTO
<Go Preset> [177]
:SetsDay and Night mode to AUTO
<Go Preset> [178]
:SetsDay and Night mode to NIGHT
<Go Preset> [179]
:SetsDay and Night mode to DAY
<Go Preset> [190]
:Sets OSD Display mode to AUTO (Except Privacy Mask)
<Go Preset> [191]
:Sets OSD Display mode to OFF (Except Privacy Mask)
<Go Preset> [192]
:SetsOSD Displaymode to ON (Except Privacy Mask)
<Go Preset> [193]
:Sets all Privacy Mask Display to OFF
<Go Preset> [194]
:Sets all Privacy Mask Display to ON
Reserved Presets
Configuration Defaults
Default Display Configuration
Default Camera Configuration
Camera ID
ON
FocusMode
SEMI-AUTO
PTZ Information
AUTO
Digital Zoom
ON
Action Title
AUTO
Line Lock
OFF
Preset Label
AUTO
WhiteBalance
AUTO
Alarm Input
AUTO
Backlight
OFF
North Direction
Pan 0˚
Day & Night
AUTO1
Privacy Zone
Undefined
Brightness
25
Iris
AUTO
Default Motion Configuration
Shutter
ESC
Motion Lock
OFF
AGC
NORMAL
Power Up Action
ON
SSNR
MIDDLE
Auto Flip
ON
SENS-UP
AUTO (4 Frame)
Jog Max Speed
120˚ / sec
Jog Direction
INVERSE
User Edit Data
Freeze In Preset
OFF
Preset 1~94, 96~128
Undefined
Park Action
OFF
Swing 1~8
Undefined
Alarm Action
OFF
Pattern 1~4
Undefined
Group 1~8
Undefined

14
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
OSD Main Screen
The OSD main screen showsinformation about the current situation ofthe camera while it is operating. Thisscreen isNOT
seen as part of the programming process.
Preset Label
The labelof the specific preset.
Action Title
Will be one of the following:
SET PRESET XXX
WhenPRESET XXX is stored
PRESET XXX
When camera reaches PRESET XXX
PATTERN X
WhenPATTERN X is in action
SWG X / PRESET XXX
WhenSWING X is in action
UNDEFINED
Whenan undefined function is called
Image Flip
Showsthat the image is currently flippedverticallyby the AutoFlip function
Camera ID
Showsthe current camera ID (address)
Alarm Information
Thisfunction isreserved forfutureuse
P/T/Z Information
Current Pan/Tilt/Zoom information (4 information points):
Pan angle in degrees
Tilt angle in degrees
Zoom level
Compass direction
Example: (15 / 4 / x 1 / N) means a Pan angle of 15 degrees, a Tilt angle of 4
degrees, Zoom (magnification) level of 1 (100%), and camera facing "North."
OSD Display of Main Screen
Action Title
Alarm
Information
Pan/Tilt/Zoom
Information
Camera ID
Image Flip
Preset
Label

15
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
For operating the OSD menus, please note the following:
•To access the OSD menu from your DVR, go to Preset 95. For more information on DVR presets and their
functions for the ENFORCER Mini PTZ Camera, please see page 13, Reserved Presets.
•Most commands are done on PELCO-compatible DVRs using the front panel keys, including the up, down,
right, and left arrows, or via a panel-mounted joystick. Such operations may also be possible using the
DVR’s remote control.
Note: For ENFORCER DR-1 DVRs, the operations are usually done using the DVR remote control.
•For many menu operations, the user must press the SEQ or FREEZE keys. For most DVRs, these are the
keys for focus in (SEQ) and focus out (FREEZE), but may be marked with other words.
For ENFORCER DR-1 Series DVRs, the operations are done using:
oMenu items which have sub-menus are surrounded by “<” and “>” brackets
(For example, <DISPLAY SETUP>).
oTo enter a sub-menu, press the SEQ key.
oTo go up one level, press the FREEZE key.
oTo move from item to item in a menu, use the arrow keys or joystick to move up/down or left/right.
oTo change the value of an item, use the arrow keys or joystick to move up/down or right/left.
oTo save a value, press the SEQ key.
oTo cancel a value or operation, press the FREEZE key.
Operating the OSD Menus
SEQ and FREEZE keys

ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
16
17
OSD Main
Screen
(page14)
SPEED DOME
CAMERA
(page18)
ZOOM
CAMERA
SETUP
(page22)
SYSTEM
INFORMATION
(page18)
DISPLAY
SETUP
(page19)
DOME CAMERA
SETUP
(page21)
SYSTEM
INITIALIZE
(page32)
SET NORTH
DIRECTION
(page19)
PRIVACY ZONE
(page20)
EDIT MASK
(page20)
MOTION
SETUP
(page24)
PRESETMENU
(page26) SWING SETUP (page28)
PATTERN
SETUP
(page29)
GROUP
SETUP
(page30)
WHITE
BALANCE
SETUP
(page22)
AUTO
EXPOSURE
SETUP
(page23)
PARKING
ACTION SETUP
(page25)
ALARM INPUT
SETUP
(reserved)
EDIT SCENE
(page27) EDIT LABEL (page27) EDIT PATTERN
(page29) EDIT GROUP
(page30~31)
OSD (On-screen Display) and Programming Flowchart
This chart shows all the screens used in programming the PTZ camera using the OSD.
To go toa particularscreen, follow the orderas shown in this flowchart.
For more information on a particular screen, go to the page number listed on the screen.

18
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
SPEED DOME CAMERA Menu
•<SYSTEM INFORMATION>:Displays system information
and configuration (see menu on page 18).
•<DISPLAY SETUP>:Configures the displayinformation
shown on the OSD MainScreen asshown on page 16 (see
menuon page19).
•
<DOME CAMERA SETUP>: Configures various functions of
the camera (see menu on page 21).
•
<SYSTEMINITIALIZE>: Initializes system configuration and
sets alldata to factory default configuration (see menu on
page31).
Thismenu shows the current configuration information as
configured on page 8.No
information canbe programmed using
thisOSD menu.
SYSTEM INFORMATION Menu
From SPEED DOME CAMERA
FIRMWARE VER
: V2.0
COLOR SYSTEM
: NTSC
PROTOCOL
: PELCO-D
ADDRESS
: 38
BAND RATE
: 9600
SYSTEM INFORMATION
EXIT
BACK
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME CAMERA SETUP>
<SYSTEM INITIALIZE>
SPEED DOME CAMERA
EXIT

19
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
DISPLAY SETUP Menu
From SPEED DOME CAMERA
Thismenu enables ordisables the information shownon the
OSD Main Screen (see page 14).
Note that setting an item to "AUTO" meansthat item will be
displayed only when itsvalue changes.
Thismenu accesses
other OSD menus for configuring a specific
pan direction of the camera as"NORTH" for certain functions,
and for setting privacy zones.
CAMERA ID
: ON
PTZ INFORMATION
: AUTO
ACTION TITLE
: AUTO
PRESET LABEL
: AUTO
ALARM INPUT
: AUTO
<SET NORTH DIRECTION>
<PRIVACY ZONE>
DISPLAY SETUP
EXIT
BACK
Thismenu sets a specificpan and tilt location as "compass
north," or a certain locationon which otherfunctions are
centered.
Using the arrow keys or joystick, point the camera towardsthe
default location, and then select "NEAR" or "SAVE" to configure
that location as"compass north."
SET NORTH DIRECTION Menu
From DISPLAY SETUP
SET NORTH DIRECTION
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL]
CAMERA ID
[ON/OFF]
PTZ INFORMATION
[ON/OFF/AUTO]
ACTIONTITLE
[ON/OFF/AUTO]
PRESET LABEL
[ON/OFF/AUTO]
ALARM INPUT
[AUTO] -- This function is
reserved for future use.
<SET NORTH DIRECTION>
See OSD menu below.
<PRIVACY ZONE>
See OSD menu on page20.

20
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
PRIVACY ZONE Menu
From DISPLAY SETUP
Thismenu configuresan area ofthe camera’s field of vision so
that it is covered by a gray mask, hiding it. For instance, this
would beused to covera neighbor’swindow,or a sensitive
window of the office.
Once configured, the gray mas
k automatically appears over that
area every time the camera pans ortiltspast it.
MASK NO
1
UNDEFINED
DISPLAY OFF
CLEAR MASK
CANCEL
<EDIT MASK>
PRIVACY ZONE
EXIT
BACK
EDIT MASK Menu
From PRIVACY ZONE
Move the camera to the target area to be masked and choose
NEAR or SAVE. The mask will be displayed as a graysquare.
EDIT MASK 1
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL]
Once the mask isdisplayed:
•Center the camera on the object to be masked.
•Use the joystick or arrow keys to adjust the mask size.
•Select"NEAR" or "SAVE" to save the masksetting.
EDIT MASK 1
[NEAR:SAVE /FAR:CANCEL]
[ ◄►: ADJUST MASK WIDTH]
[ ▲▼: ADJUST MASK HEIGHT]
MASK NO
1~4. Select the mask number. If that mask
was alreadyconfigured,the camera will
move to the where it was set. Otherwise,
UNDEFINEDwill be displayed under
MASK NO.
DISPLAY
[ON/OFF] Shows ON if the selected mask
is active, shows OFF if that mask is not
active.
CLEAR MASK
Deletesdata in the selected mask.
<EDIT MASK>
See EDIT MASK menu below.

21
ENFORCER Mini PTZ Camera
SECO-LARM, U.S.A., INC.
DOME CAMERA SETUP Menu
From SPEED DOME CAMERA
<CAMERA SETUP>
Goesto the ZOOM CAMERA SETUP menu
for configuring manyof the generalfunctions
of the zoom camera module.See page 22.
<MOTION SETUP>
Configuresthe general functions ofthe pan
and tiltmotions. See page 24
<PRESET SETUP>
Configures up to 127 different preset
locations to which the camera can be
instantly moved. See page 26.
<SWING SETUP>
Configuresup to four different swing motions
between two different preset locations. See
page28.
<PATTERN SETUP>
Configures up to four pan/tilt patterns, with
eachpattern consisting of a starting position,
an ending position, and the complete
pan/tilt/halt movementbetween those two
points. See page 29.
<GROUP SETUP>
Configures up to eight groups of motions,
with each group consisting ofany
combination of up to 20 presets, swings,
patterns, and temporaryhalts in the action.
See page 30.
<CAMERA SETUP>
<MOTION SETUP>
<PRESET SETUP>
<SWING SETUP>
<PATTERN SETUP>
<GROUP SETUP>
DOME CAMERA SETUP
EXIT
BACK