SECO-LARM ENFORCER MVE-PB020Q User manual

ENFORCER Composite Video Balun
4SECO-LARM U.S.A., Inc.
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in
whole or in part, without the written permission of SECO-LARM.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: sales @ seco-larm.com
Mi-MVE-PB0x0Q.docx
Specifications:
Troubleshooting:
MVE-PB010Q MVE-PB020Q
Video
Max. range 2,230’ (680m)
Video format YPbPr or RGB (1080p/1080i/720p/720i/480p/480i)
Maximum input 1Vpp
Insertion loss Max. 2dB per pair over the freq. range from DC to 8MHz
Return loss Max. 2dB per pair over the freq. range from DC to 15MHz
Common mode rejection Greater than 40dB at 8MHz
Bandwidth DC to 8MHz
Power No power required
Connections
Wire type UTP (unshielded twisted pair)
Wire category 20 - 24 AWG @ screwless terminal blocks
CAT5e or CAT6 for improved range
Connectors Input RCA male RCA female
Output Terminal block RJ-45
A
ttenuation DC ~ 5 Mhz, 1.5 dB max
Other
Dimensions 2
1
/
4
” x
5
/
8
” x
9
/
16
” (57 x 16 x 14 mm) 2” x
7
/
8
” x
3
/
4
” (51 x 22 x 19 mm)
Humidity range 0 ~ 95%
Temperature Range 14°~165°F (-10
°
~74
°
C)
Case PC plastic
Composite video balun does not function
correctly yMake sure all input and output connections are connected firmly to the balun
yMake sure the video input device is turned on
yMake sure the video output device is turned on
yTest the Cat5e/6 cable between the baluns
yMake sure the RJ-45 connector is wired according to
T568B wiring standards
PITLW2
PITSW4
Also Available from SECO-LARM:
HDMI over Cat5e/6 y Component Video over Cat5e/6 y Digital and Analog audio overCat5e/6
MANUAL
MVE-PB010Q
Passive Composite Video Baluns
The ENFORCER Composite Video Baluns are the quick, low-cost way to connect composite or
component (YPbPr) video devices at greater distances than traditional video cabling methods. The
video baluns work in pairs to allow video signals to be transmitted up to 2,230’ (680m) over
low-cost Cat5e/6 unshielded twisted pair (UTP) cable instead of costly composite video cable.
•
Passive operation – No external power
required
•Uses low-cost Cat5e/6 cable instead of costly
composite video cables
•Small size for easy installation behind most
video devices
•
High immunity from interference – Built-in
impedance coupled device and noise filter
•Gold-plated connector for longer life and better
reliability
•Limited lifetime warranty
NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.
MVE-PB020Q
(standard) (snap-in)

ENFORCER Composite Video Balun
2SECO-LARM U.S.A., Inc.
Overview:
Installation:
1. Make sure the maximum distance between the video
source and display does not exceed the maximum range of
the video baluns.
2. Run the UTP cable from the video source to where it will
be connected to the display destination.
3. Connect UTP cable to the two video baluns.
For standard baluns slide the cover off of the video balun
and connect two wires to the terminal block located inside
the balun. See figure 1.
4. For the correct length of bare wire, see figure 3 on page 3.
For snap-in baluns connect the RJ 45 plug according to
T568B wiring standards. Plug the video baluns into the RCA
connectors on the source and destination.
NOTE: The baluns are polarity-sensitive. Observe
correct polarity.
Wire Exit Holes
NOTE: Composite baluns are connected in pairs. One connects to the video source RCA
output connector, and the other connects to the video destination RCA input connector.
Center-pin
(positive)
Shielding
(ground)
Figure 1 – Video balun with
cover removed
Shielding
(ground)
Pin 7 (-) Pin 8 (+)
Modular Balun:
Snap-in Balun:
Please use T568B wiring standard for RJ45 connectors.
Figure 2 – Connecting
Cat5e/6 Cable
ENFORCER Composite Video Balun
SECO-LARM U.S.A., Inc 3
Sample Application #1: Standard Composite Video Baluns
Composite Video
Source, VCR,
Gamin
g
S
y
stem
Display
Up to 2,230’ (680m)
5. Test the connection by powering up the video
source and destination.
6. If using standard baluns, replace the covers on the
video baluns and make sure the wires exit through
the two small holes on the back of the units.
NOTE: Bare wires must not be exposed
outside the video baluns.
Sample Application #2: Modular Snap-in Composite Video Baluns
MVE-PB010Q MVE-PB010Q
(wall plates not included)
Up to 2,230’ (680m)
M
V
E-PB020Q M
V
E-PB020Q
Figure 3 – Video balun with
cover removed
Cat5e/6
ENFORCER
Composite Video Balun
SECO-LARM
Ideal Copper Length
Expose ¼” copper wire of the UTP for
connection to the balun. Use the “ideal
copper length” guide on the balun.
SECO-LARM has a complete line of audio/video products.
Please visit www.seco-larm.com for more information.
Display
ENFORCER
ENFORCER
Composite Video
Source, VCR,
Gaming System
Component Video
Source Display
MVE-PB010Q MVE-PB010Q
Sample Application #3: Component Video
ENFORCER
ENFORCER
ENFORCER
ENFORCER
ENFORCER
ENFORCER
Y Y
Pb Pb
Pr Pr
Up to 2,230’ (680m)