SECO-LARM ENFORCER E-964-Q660Q User manual

Multi-Frequency
Quad Photobeam Detectors
E-964-Q660Q– 660ft.(200m)outdoors, 1320ft. (400m) indoors
E-964-Q495Q– 495ft.(150m)outdoors, 990ft.(300m)indoors
E-964-Q330Q– 330ft.(100m)outdoors, 660ft.(200m)indoors
E-964-Q165Q– 165ft.( 50m)outdoors, 330ft.(100m)indoors
®
ENFORCER
SENSOR
MANUAL
SECO-LARM®

2
Features:
●Four selectable beam frequencies to eliminate
interference between multiple units for
enhanced perimeter protection.
●Audible beam alignment (buzzer).
●Beam strength indicator (5 LEDs).
●Environmental Output (Selectable N.O. or N.C.):
Signal is sent if a degradation in environmental
conditions is detected such as thickening fog to
preventfalsealarms.
●Built-inheater.
●IP-55 ingress protection.
●Lensed optics reinforce beam strength and
provide excellent immunity to false alarms due
torain, snow,mistetc.
●Automatic input power filtering with special
noise rejection circuitry.
●Voltage testing points for fine tuning the beam
alignment.
●Inputvoltage:12-24VAC/DC.
●Response time adjustable for nearly all
situations.
TABLE OF CONTENTS
Introduction .................................................. 2
Features ....................................................... 2
Overview ....................................................... 3
Wiring Diagram ............................................ 4
Choosing a Location .................................... 4
RunningtheCable ...................................... 4
Multiple Sensor Sample Applications .......... 5
Typical Installations..................................... 5
WiringtheTransmitter–WallMount ........... 6
WiringtheTransmitter–PoleMount ........... 6
Wiring.......................................................... 6
ExamplesofWaysToConnectSensors ...... 7
Selectable4-channelBeamFrequency...... 8
ReceiverDetail............................................ 8
BeamAlignmentTemplate .......................... 8
BeamAlignment ......................................... 9
AdjustingtheResponseTime ................... 10
TestingtheUnit ......................................... 10
Specifications ........................................... 10
Dimensions............................................... 11
Troubleshooting........................................ 11
Introduction:
The ENFORCER E-964-Q Series Quad-Photobeam Sensors are ideal for long-distance protection.
Four selectable beam frequencies allow for superior perimeter protection by eliminating crosstalk and
interference between multiple units. False alarms created by animals and falling leaves are
minimized by the sensor's detection method of all 4 beams simultaneously broken.
The E-964-Q Series of sensors is designed to work in even the most extreme conditions. Abuilt-in
heater automatically turns on and off depending on the outside temperature. An environmental control
output senses a slow degradation in beam strength when weather conditions worsen preventing false
alarms.
Installation and alignment is quick and easy with the ENFORCER E-964-Q Series. The built-in laser
and visual alignment systems quickly and easily pinpoint the approximate mounting location for the
transmitter and aid in aligning the transmitter and receiver units once mounted. Abeam strength
indicator clearly displays the strength of the beam at the receiver with 5 LEDs.
SECO-LARM®U.S.A.
ENFORCER Quad-Photobeam Detectors

ENFORCER Quad-Photobeam Detectors
3
SECO-LARM®U.S.A.
Viewfinder
Horizontal
adjustment grip
Red signal LED
NC/NO switch
On/Off
Beam channel selection DIP
switches
Response time (50ms~700ms)*
Heater power
Environmental output
Horizontal
adjustment grip
Viewfinder for alignment
Vertical
adjustment screw
Green power LED
Power 12~24V AC/DC
Alarm output
Beam strength
indicator (5 LEDs)
Tamper output
Voltage output probes
Vertical
adjustment screw
Alignment laser
On/Off switch for laser
On/Off switch for laser
Alignment laser
(Receivershown)
IMPORTANT – Do not connect to power until the sensor is completely installed and the
installation has been double-checked.
Fig.1:Overview
Environmental
output
}
*Factory default 50ms

4
ChoosingaLocation
1. Find a suitable location for the receiver within wiring distance of a power supply and the alarm panel.
2. Establish a clear line-of-sight area between the receiver location and the transmitter location.
3. Make sure no trees or vegetation will cause false alarms during windy conditions.
4. Find locations away from standing water that could be splashed on to the receiver or the transmitter.
5. Do not mount the receiver where sunlight or bright lights shine directly into the unit.
6. Installat a distanceof 32" to 39"(80to 100 cm) abovetheground for most situations.Seefig. 3.
Fig.2:WiringDiagram
SECO-LARM®U.S.A.
Transmitter
Heater
Power AC/DC
12-24V
(non-polarity)
Tamperoutput
N.C. switch
1A @ 30VDC
(Max.)
Heater
Environmental
output(NO/
NC)
1A @ 125 VAC
/24VDC
Receiver
N.C.
N.O.
Com
Alarm O/P
1A @
125VAC
/24VDC
7
6
5
4
3
2
1
Tamperoutput
N.C. switch
1A @ 30VDC
(Max.) 7
6
Power AC/DC
12-24V
(non-polarity) 2
1
Running the Cable
Run a cable from the alarm control panel to the photobeam sensor. If burying the cable is required, make
sure to use electrical conduit. Shielded cable is strongly suggested. See Table 1 for maximum cable length.
Table1: CableLength
Note (1): Max. cable length when two or more sets are connected is the value shown in Table 1 divided by the no. of sets.
12V 24V 12V 24V 12V 24V
WireSize 12V 24V
E-964-Q165Q E-964-Q330Q E-964-Q495Q Model E-964-Q660Q
AWG22
AWG20
AWG18
AWG17
320m
1,050ft.
550m
1,800ft.
800m
2,600ft.
980m
3,190ft.
2,800m
18,000ft.
4,800m
15,750ft.
7,200m
23,620ft.
8,800m
28,870ft.
280m
920ft.
450m
1,480ft.
700m
2,300ft.
850m
2,790ft.
2,400m
7,870ft.
4,200m
13,780ft.
6,200m
20,340ft.
7,600m
24,930ft.
110m
390ft.
170m
560ft.
250m
820ft.
310m
1,020ft.
900m
2,950ft.
1,400m
4,590ft.
2,200m
7,220ft.
2,600m
8,530ft.
200m
660ft.
350m
1,150ft.
500m
1,640ft.
590m
1,940ft.
1,600m
5,250ft.
3,000m
9,840ft.
4,200m
13,780ft.
5,200m
17,060ft.
ENFORCER Quad-Photobeam Detectors

5
Multiplesensorsampleapplications
1. Long distance series application.
Tx Rx Rx Tx Tx Rx TxRx
Channel #1 Channel #3 Channel #4
2. Two layer (double stacked) applications.
3. Perimeter security applica-
tion.
Rx
Tx
Channel #3
Channel #2
Rx
Tx
Channel #4
Channel #1
Tx
Rx
Rx
Tx
Tx Rx Rx Tx Tx Rx
Tx Rx Tx Rx
Channel #1 Channel #2 Channel #3
Channel #4 Channel #3 Channel #2
Rx Tx
4. Single pair multiple layer application.
Channel #1
Channel #2
Channel #4
Tx
Tx
Rx
Rx
Tx Rx
Channel #3
Tx Rx
Rx Tx
Rx Tx
Channel #4
Channel #1
Channel #2
SECO-LARM®U.S.A.
Fig.3:TypicalInstallations
Side
Views
Top
Views
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12


123
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
123
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12

  
123
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
123
1234
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1
23
4
1234
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12

123
1
2
3
123
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12


123
1
2
3
123
1234
1
23
4
1234
32" to 39"
ENFORCER Quad-Photobeam Detectors

6
Fig.7:
PoleMount
Wiring the Transmitter
– Pole Mount
(NOTE – Pole mounting bracket included.)
1. Removethe cover. Remove thescrew under
the lens unit in order to detach the mounting
plate.Seefig.4.
2. Break a hole in the mounting plate’s rubber
grommet, and pull the cable through the
grommet’s hole. Then run the cable through
thehole near thebottom of thesensor unit so
it comes out the front. Use the included
mounting bracket to mount to the pole. Then
reattach the sensor unit to the mounting plate,
connect the wires, and snap on the cover.
Seefig.7.
Wiring(fig.8)
1. Screwthewirestightlytoavoidslippingoffthe
terminals,butnotsotightthattheybreak.
2. Screws on terminals which are not used
should be tightened.
3. Grounding may be necessary, depending on
the location.
WiringtheTransmitter– WallMount
1. Removethe cover. Remove the screwunder the
lens unit in order to detach the mounting plate.
Seefig.4.
2. If the sensor wiring comes from inside the wall –
Break a hole in the mounting plate’s rubber
grommet, and pull the cable through the
grommet’s hole. Then run the cable through the
holenear the bottomof the sensorunit so it
comes out the front. Using two of the included
mounting screws, attach the mounting plate to
the wall. Then reattach the sensor unit to the
mounting plate, connect the wires, and snap on
thecover.Seefig.5.
3. Ifthe sensor wiring is run along the surface of the
wall – There are four plastic knockouts on the
backof the sensorunit, two on topand two on
bottom. Break out the appropriate knockout, and
pull the wiring through the knockout. Then run the
wiring through the hole near the bottom of the
sensorunitso it comes outthefront. Using two of
the included mounting screws, attach the
mounting plate to the wall. Then reattach the
sensor unit to the mounting plate, connect the
wires,andsnap on the cover. See fig. 6.
Fig. 5:
Wall Mount,
Wire from
Inside Wall
Fig. 6:
Wall Mount,
Wire Runs
Along Wall
– or –
Fig.4:
Removethe
Transmitter
cover
SECO-LARM®U.S.A.
ENFORCER Quad-Photobeam Detectors

7
Fig.8: ExamplesofPossibleWaysToConnectOneorMoreSensors
Example connection 3 - Dual Sensors, Separate Channels
Example connection 1 -
Standard
Example connection 4 - Two stacked
➀➁ ➀➁➂➃
}Power
}
Tx Rx
➀➁ ➀➁➂➃
Tx Rx
➀➁ ➀➁➂➃
}Power
}Alarmsignal
Tx
Ch1
➀➁ ➀➁➂➃
Rx
Ch1
Tx
Ch2 Rx Ch2
N.C.Alarm
(ch. 1)
}N.C.Alarm
(ch. 2)
Example connection 2 - In-line Single Channel
➀➁ ➀➁➂➃
Controlpanel
(12~24VAC/VDC)
}Power
}
Tx Rx
N.C.Alarm
signal
Tx
➀➁ ➀➁➂➃
}Power
Rx
➀➁ ➀➁➂➃
Tx Rx
N.C.Alarm
signal
}
Controlpanel
(12~24VAC/VDC)
Controlpanel
(12~24VAC/VDC)
Controlpanel
(12~24VAC/VDC)
SECO-LARM®U.S.A.
ENFORCER Quad-Photobeam Detectors

ENFORCER Quad-Photobeam Detectors
8
Important – The transmitter and receiver
must be programmed to the same channel.
Selectable4-channelbeamfrequency:
The sensor beam frequency can be set at different
levelson-siteto avoid interference fromother
photobeam sensors nearby. To select between four
different beam frequencies, adjust the beam
channel switch of the transmitter side and receiver
side. See pg. 3, fig. 1 for switch location and table 2
for switch position.
Freq. channel CH1 CH2 CH3
Switch position
CH4
12 12
Table2:Channel
BeamFrequencySelectionChart
12
12
NO
NO NO NO
Fig.9:ReceiverDetail
Fig.10:IncludedBeamAlignmentTemplate:
Use the included SECO-LARM template to aid in aligning
thetransmitterand receiver.
SECO-LARM®U.S.A.
DIP Switch Channel Selector
Beam Alignment Buzzer Switch
Beam Alignment Strength Indicator Switch
Response Time Adjustment

ENFORCER Quad-Photobeam Detectors
9
Fig.11:
HorizontalandVertical
SensorAdjustment
Horizontal
Adjustment
Finger Grips
View Finder
BeamAlignmentProcedure
1. Removethe sensor cover and turn On the top and
bottomlasersofboth the transmitter and receiver.
There are a total of four lasers.
2. Adjustthetransmitter'ssensorunitverticallyand
horizontallyuntil the red dotiscentered on the
receiverand the receiver’s signalLED turns Off.
3. Repeatstep2forthereceiverthenturn Off the
lasers.
4. Lookthrough the viewfinderonthe transmitter’s
lowersensorand adjust it verticallyandhorizontally
untilthereceiver is clearly seeninthe viewfinder.
5. Repeatstep4for thereceiver.
6. Turn On the beam alignment buzzer DIP switch
(fig.9).Ifthebeams are not aligned the buzzer will
sound.
7. Coverthetopsensoronthereceiverwiththe
included template (as shown in fig. 10).Adjust the
horizontal angle of the receiver’s lower sensor
verticallyandhorizontallyuntilthebuzzerstops
sounding. Repeat while covering the lower sensor
andadjusting the top sensor.
8. TurnthebuzzerOff.
9. Turn On the beam strength Indicator DIP switch
(fig. 9). If the beams are not aligned, the indicator
willdisplay little orno beam strength,see fig.12.
10.Coverthetopsensoronthereceiver.Adjustthe
horizontal angle of the receiver’s lower sensor
verticallyand horizontally until thebeamstrength
indicator displays a strong signal. Repeat while
covering the lower sensor and adjusting the top
sensor.
11.Turn the beam strength indicator Off.
Table.3:VoltageOutput
Fig.12:
BeamStrengthIndicator
Vertical
Adjustment
Screw
Strongest
Good
OK
Poor
Bad
No Signal
SECO-LARM®U.S.A.
Fig.13:UsingaMultimeter
forFine Tuning
The transmitter and receiver sensor units
can be adjusted ±15° vertically and ±90°
horizontally once the unit is mounted and
power is connected.
FineTuning
The most accurate way to align the transmitter and
receiveristomeasure the voltage using thevoltage
outputjack (fig.13).
1. Setthe range of amultimeterto0~10VDC.
2. Insertthe red probe into the (+) terminaland the
black probe into the (-) terminal.
3. Using Table 3, adjust the receiver’s sensors
verticallyand horizontallyuntilthebestpossible
voltageoutput isachieved.
VoltageOutput
AlignmentQuality 0V <1.1V 1.1~1.4V 1.4~1.7V 1.7~2.0V >2.0V NoSignal Bad Poor OK Good Strongest

ENFORCER Quad-Photobeam Detectors
10
Model
Max. range (outdoor)
Max. range (indoor)
Current (Tx & Rx)
Current(Tx & Rx& heaters)
Inputvoltage
Response time
Detection method
Selectable beam frequencies
Alarmoutput
Tamper output (Tx & Rx)
Environmental output
Beam-strength indicator
Signal LED (Rx)
Power LED (Tx & Rx)
Laserwavelength
Laser output power
Alignment angle
Operating temperature
Weight
Ingress protection
Case
Dimensions
12~24VAC/VDC(non-polarity)
50ms~700ms (variable, factory default 50ms)
All 4 beams simultaneously broken
Four (4) channels
Form"C"relayCOM/N.O./N.C.1A@125VAC/24VDC
NCswitch,1A@120VAC
SelectableN.O.orN.C.1A@125VAC/24VDC
5 LEDs indicate signal strength from high to low
Red LED ON -
beam is broken or Tx and Rx out of alignment
Green LED - illuminated when power is on
650nm
≤ 5mW
Horizontal:±900Vertical:±150
-13~1310F (-250~ 550C)
5.7lbs.(2.6kg)
IP55
PC Resin
151/4" x 47/16"x45/16"(387 x 113x 110mm)
E-964-Q165Q
165' (50m)
330’ (100m)
110mA
260mA
E-964-Q330Q
330’ (100m)
660’ (200m)
115mA
270mA
E-964-Q495Q
495’ (150m)
990’ (300m)
120mA
280mA
E-964-Q660Q
660’ (200m)
1320’ (400m)
125mA
290mA
SECO-LARM®U.S.A.
(300ms)
700ms50ms
Fig.14:
Adjustingthe
ResponseTime
Adjusting the Response Time (IMPORTANT)
1. The response time adjustment knob sets how long the beam can be
interrupted before triggering the alarm (see fig.14):
a. Ashortresponse time(highsensitivity)is suitableforcatchingfast
moving intruders, but more susceptible to false alarms.
b. Alongresponsetime (lowsensitivity)reducesfalse alarms,butfast
movingintruders may not trigger thesensor.
2. Adjustthe knob to the site’ssituation. Youmay need to make adjustments
laterafterthewalk-throughtest.
1. Powerup the transmitterandreceiver.
2. Ifthe redalarm LED remains steady ON even when
the beam is not interrupted, re-adjust the alignment.
3. Walkbetween the transmitterandreceiverto interrupt
thebeams. Walkatvariousspeeds,andadjustthe
delay time adjustment knob as needed.
Testing the Unit
NOTE – The alarm will be triggered only if
both the upper and lower beams are
simultaneously interrupted.
IMPORTANT – Test the detector periodi-
cally to ensure the alignment and delay time
settingsare suitableforthesite.
* This is the minimum time interval between breaking of both beams which will trigger the output. Setting the interval longer will
reduce false alarms from birds or falling leaves, etc., while setting it shorter will detect faster moving objects.
Table4: Specifications
IMPORTANT: Notethatthe response time is setat the factoryto theshortest time (50ms).After installation is complete, pleaseadjust to
bestsuitthesitesituation.

11
_________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________
Upper
View
43STPoleSize
Side View
RearView
FrontView
151/4”(367mm)
47/16”
(113mm)
Fig.15: Dimensions
411/32”
(110mm)
Troubleshooting:
Transmitter LED not lit
Receiver LED does not light when interrupted
Beams are interrupted and LED lights, but the
alarm does not trigger.
Signal LED continuously lit
Alarm trigger becomes erratic in bad weather
Frequent false alarm triggers
Make sure the input power to the transmitter is
12to24VAC/VDC.
Check the input power to the receiver is 12 to 24
VAC/VDC.
Check the continuity of the wiring from the
receiver to the alarm.
Clear any obstacles between the transmitter and
receiver.
Clean the lenses of both units.
Check overall system installation.
Realign the lenses.
Adjusttheresponsetime.
Change location of transmitter and receiver.
SECO-LARM®U.S.A.
ENFORCER Quad-Photobeam Detectors

12
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: [phone] [phone] Website:www.seco-larm.com
E-mail:[email protected] MI_E-964-QxxxQ_190531.pmd
PITSW3
Also available from SECO-LARM:
E-960-D290Q E-932-D33TBQ E-9622-4B25
•
Availablein4,6,8or10beams.
•
Range: 25 ft.outdoor,
50ft. indoor.
•
Slim-linedesign
7
/
8
"x1
5
/
16
".
•
WeatherproofIP65construction.
•
Triggersonbreakingofany
singleor2adjacentbeams
(programmable).
•
E-932-D33TBQ–Photoelectric
Through-BeamSensor.
•
Suitableforentrances,hallways,
roominofficeor home.
•
Fitssingle-gangbox.
•
Adjustablealignmentanglefrom
+/-15
o
horizonatally/vertically.
•
Range:upto290'outdoors.
•
Lensedopticsreinforcebeam
strengthandprovideexcellent
immunitytofalsealarmsduetorain,
snow,mist,etc.
•
Weatherproof,sunlightfilteringcase
forindoorandoutdoorconditions.
•
Quickeasyinstallationwithbuilt-in
laser-beamalignmentsystem.
Twin Photobeam
Detectors Flush-Mount Photobeam
Sensors
SECO-LARM'sENFORCERTwinPhotobeamdetectorseriesareprotectedbythefollowingpatents:
U.S.pat.no. D485774 ;Taiwan pat.no.89463 ; Chinapat.no. ZL0331103.0
Otherinternationalpatentsarepending.
Curtain/BarrierSensors
WARRANTY: ThisSECO-LARMproductiswarrantedagainstdefectsinmaterialandworkmanshipwhileusedin
normalserviceforthree(3)yearsfromthedateofsaletotheoriginalcustomer.SECOLARM’sobligationislimitedtothe
repairorreplacementofanydefectivepartiftheunitisreturned,transportationprepaid,toSECOLARM.ThisWarranty
isvoidifdamageiscausedbyorattributedtoactsofGod,physicalorelectricalmisuseorabuse,neglect,repairor
alteration,improperorabnormalusage,orfaultyinstallation,orifforanyotherreasonSECOLARMdeterminesthat
suchequipmentisnotoperatingproperlyasaresultofcausesotherthandefectsinmaterialandworkmanship.The
soleobligationofSECOLARMandthepurchaser’sexclusiveremedy,shallbelimitedtothereplacementorrepaironly,
atSECOLARM’soption.InnoeventshallSECOLARMbeliableforanyspecial,collateral,incidental,orconsequential
personalorproperty damageofanykindtothepurchaseror anyoneelse.
NOTICE: The SECO-LARMpolicyisoneofcontinualdevelopmentandimprovement.Forthatreason,SECOLARM
reservestherighttochangespecificationswithoutnotice.SECOLARMisalsonotresponsibleformisprints.All
trademarksarethepropertyofSECO-LARMU.S.A.,Inc.ortheirrespectiveowners.Copyright©2019SECOLARM
U.S.A.,Inc.Allrightsreserved.
ENFORCER Quad-Photobeam Detectors