SECO-LARM ENFORCER VS-1AHHAQ User manual

ENFORCER HDMI Surge Protector
4SECO-LARM U.S.A., Inc.
Troubleshooting:
NOTICE
: The information and specifications printed in this manual are current at the time of publication. However, the SECO-
LA M policy is
one of continual development and improvement. For this reason, SECO-
LA M reserves the right to change specifications without notice.
SECO-LA M is also not responsible for misprints or typographical errors.
Copyright © 2015 SECO-LA M U.S.A., Inc. All rights reserved. This material may not be reproduced or
copied, in whole or in part, without the
written permission of SECO
-
LA M.
WARRANTY
: This SECO-
LA M product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original consumer customer. SECO-
LA M’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-
LA M. This Warranty is void if damage is caused by
or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage,
or faulty
installation, or if for any other reason SECO-LA M determines that such equipment is not operating properly as a result o
f causes other than
defects in material and workmanship. The sole obligation of SECO-
LA M, and the purchaser’s exclusive remedy, shall be limited to
replacement or repair only, at SECO-LA M’s option. In no event shall SECO-LA M be liable for any special, c
ollateral, incidental, or
consequential personal or property damages of any kind to the purchaser or anyone else.
Video image is weak or faded
•educe the cable length—max. 16.4ft (5m) for 1080p, 11.5ft
(3.5m) for 4K2K
•eplace with a higher-grade HDMI cable
No video image
•Double-check that the cables were connected properly
•un a continuity test on all wires in the cable
•Make sure source and the display are powered
•Make sure that there are no problems with the HDMI source,
HDMI cables, or HDMI display by removing the HDMI surge
protector.
MiVS-1AHHAQ_141215.docx
PI
TSW4
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: www.seco
-
larm.com
E-mail: [e-mail]
IMPORTANT
: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
aws
and statutes related to monitoring and recording audio and video signals. SECO-LA M will not be held responsible for
the use of this product
in violation of any current laws or statutes.
WARNING
:
Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock,
damage the device, and void the warranty. Do not open the case of this device, as there are no field-serviceable components inside.
Also
Available from ECO
-
LARM:
Video Surge Protector
V -1V12BQ
PoE Surge Protector
IPV-P188Q
HD
-
SDI Surge Protector
V -1V22AQ
IP Surge Protector
IPV-PD88Q
V -1AHHAQ
Manual
HDMI
Surge Protector
•
Helps prevent damage to sensitive HDMI equipment such as
players, monitors, and projectors
•Intercepts repeated surges and spikes that could damage
HDMI A/V equipment
•Built-in ESD, EFT
•eaction speed <1ns
•Passive operation – no external power required
•Includes a 12” (30cm) grounding wire for convenient connection to
ground

ENFORCER HDMI Surge Protector
2SECO-LARM U.S.A., Inc.
To HDMI
Input
Unprotected
End
1" (26mm)
To
HDMI
Output
Protected
End
2
3
/
16
" (56mm)
Grounding Wire
Attachment Location*
(One on each end)
1" (26mm)
*
Note: There i a ‘Grounding Wire Attachment Location’ included on both end of the HDMI Surge
Protector. Grounding wire can be attached to either of the e location .
Introduction
:
The ENFO CE
HDMI
Surge Protector is a passive device that helps
protect
sensitive
HDM
I
equipment from power surges. The device can be deployed in new installations or existing
ones.
The ENFO CE HDMI Surge Protector should be installed between HDMI equipment such as
players, monitors, and projectors to protect against surges that could damage the video
equipment.
NOTE: For the best protection, installing two surge protectors is recommended: one at each
end of the cable.
ESD protection
15kV (ESD), 8kV (Contact)
EFT protection
40A (5/50ns)
Surge
protection
5A (8/20ns)
Surge reaction speed
<
1ns
Connector
In
HDMI
Out
HDMI
Dimensions
2
3
/
16
"x1"x1" (
5
6
x2
6
x2
6
mm)
Weight
1.2
-
oz (35
g)
Material
Aluminum
Operating temperature
32
°~
131°F (
0°~
55
° C)
pecifications:
Overview:
1x
HDMI Surge Protector
2x
Mounting screws
1x
12" (30cm) grounding wire
1x
Manual
2x
Plastic wall anchors
1x
Grounding wire screw
Parts List:
ENFORCER HDMI Surge Protector
SECO-LARM U.S.A., Inc. 3
To ground
2
(can be attached to either end of surge protector)
HDMI
Player
(Not Protected)
HDMI
Surge
Protector HDMI cable
1
Protected
End
HDMI
Monitor
(Protected) Unprotected
End
Short
HDMI
cable
(Ground can be attached to either end of surge protectors)
HDMI
Monitor
(Protected)
Short
HDMI
cable
HDMI
Surge
Protector
HDMI
Surge
Protector
HDMI cable
1
To ground
2
To ground
2
HDMI
Player
(Protected)
Protected
End
Protected
End
Unprotected End
Short
HDMI
cable
Protecting Multiple Devices:
Installation:
1.
Detach the
existing
HDMI
cable
1
from the device to be protected
and attach that
cable to the
“Unprotected” end of the HDMI Surge Protector.
2. Attach another HDMI cable (not included) between the device to be protected and the
“Protected” end of the HDMI Surge Protector. The protected cables should be as short as
possible and should not cross unprotected cables.
3. Connect the ground wire from the HDMI Surge Protector (either end
2
) to earth ground. The
system should use a single ground point and the protected device should be isolated from
ground.
1.
Detach the
HDMI
cable
1
from both devices to be protected.
2. Attach an HDMI Surge Protector to each end of the HDMI cable, ensuring that the cable is
connected to the “Unprotected” end of the HDMI Surge Protector.
3. Attach another HDMI cable (not included) between each device to be protected and the
“Protected” end of its respective HDMI Surge Protector. For best protection, the protected
cables should be as short as possible and should not cross unprotected cables.
4. Connect the ground wire from each HDMI Surge Protector (either end
2
) to earth ground. The
system should use a single ground point and the protected device should be isolated from
ground.
Protecting a ingle Device:
NOTE
: These instructions assume that
2
HD
M
I
devices
have
already
been
connected together.
1
Note:
The
maximum
length of the HDMI cable will depend on the cable’s specification and quality.
2
Note: There is a ‘Grounding Wire Location’ included on both ends of the HDMI Surge Protector.
Grounding wire can be attached to either of these locations.