Seconique Furniture Jasper low sleeper bed blue gloss User manual

ASSEMBLY INSTRUCTIONS
2329HN
2329HN
RIGHT OPTION 1
RIGHT OPTION 1
SEC/AY/12/19/HN1
1
JASPER LOW SLEEPER BED
BLUE GLOSS
IMPORTANT
FOR DOMESTIC USE ONLY
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• Never drag or push products as this could cause damage to the joints making it inferior.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Do not place this product next to a radiator or in direct sunlight.
• Do not drag or push items across your high gloss furniture as this may cause the surface to scratch.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack if subjected to heat.
Therefore it is recommended that room temperature is maintained, with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking will occur.
• For general cleaning use a soft cotton or micro fibre cloth, and do not use detergents of any kind.
• From time to time it may be necessary to tighten fittings, regular inspections should be carried out.
• Do not place on a wet or damp floor as staining may occur to your floor.

06
08
07
07
05
03
04
01
02
02
01
14
13
10
12
11
09
16
16
19
20
20
21
22
18
18
17
17
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
SEC/AY/12/19/HN1
2
ITM/D523-

SEC/AY/12/19/HN1
Please Note:
The below parts have all been stamped with the
part number to help identify them during assembly.
PARTS LIST
Part Number Part Code Part Description Quantity Carton
01 S200-206-016-HN1-01 Top/Middle Panel x2 2/4
02 S200-206-016-HN1-02 Upper Divides x2 4/4
03 S200-206-016-HN1-03 Lower Left Divide x1 4/4
04 S200-206-016-HN1-04 Lower Right Divide x1 4/4
05 S200-206-016-HN1-05 Base Panel x1 4/4
06 S200-206-016-HN1-06 Front Crossbeam x1 2/4
07 S200-206-016-HN1-07 Base Support x2 4/4
08 S200-206-016-HN1-08 Back Crossbeam x1 2/4
09 S200-206-016-HN1-09 Footboard Panel x1 1/4
10 S200-206-016-HN1-10 Bed Back Crossbeam x1 2/4
11 S200-206-016-HN1-11 Right Siderail x1 3/4
12 S200-206-016-HN1-12 Left Siderail x1 3/4
13 S200-206-016-HN1-13 Headboard Panel x1 1/4
14 S200-206-016-HN1-14 Back Panel x1 2/4
15 S200-206-016-HN1-15 Slats x15 2/4 and 4/4
16 S200-206-016-HN1-16 Ladder Side x2 3/4
17 S200-206-016-HN1-17 Ladder Step Support x2 3/4
18 S200-206-016-HN1-18 Ladder Step x2 3/4 and 4/4
19 S200-206-016-HN1-19 Drawer Front x2 4/4
20 S200-206-016-HN1-20 Drawer Side x2 4/4
21 S200-206-016-HN1-21 Drawer Back x2 4/4
22 S200-206-016-HN1-22 Drawer Bottom x2 4/4
*Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe!!!
*Please assemble on a clean soft suface to avoid damage.
*Please check contents and read the instructions before commencing assembly.
*Assemble this product following the enclosed instructions carefully.
*Please take care to avoid damaging panels during assembly.
3
ITM/D523-

38x
A34x
22x
06xD
F
B
02x
S
Glue
08x08x
JK
Cam Bolt
02x
Q67x
02x
T
U
Spacer
06x
H
Nail 1/8x23mm
38x
L
Cylindrical Nut
08x
04x
02x
02x
O
N
R
P
Ladder Bracket
Plastic Foot
30x
E
14x
M
Metal Support
70x
G
2 People Required
SEC/AY/12/19/HN1
08x
I
Dowel O8x60mm
Plastic Foot 25x30mm Plastic Foot 12x15mm
Drawer Runners Hole Plugs
Flat Head Screw
O3,5x10mm
Flat Head Screw
O3,0x30mm
Flat Head Screw
O3,0x16mm
Flat Head Screw
O3,5x40mm
Dowel O5x25mm
Flat Head Screw
O4,5x60mm
Cam Nut O12mm
02x
V
Union Screw 15mm
52x
C
Nail 10x10mm
4
ITM/D523-
FITTINGS LIST
TIPS FOR FITTINGS CAM-LOCKS
USE
DO NOT USE
When fitting cam nut. Ensure starting
position is correct before you insert
connecting cam bolt turn clockwise until
secure.
CAMBOLT
Tighten until shoulder in
flush with panel. Do not
overtighten or undertighten
(see example beside).
Shoulder
Panel Panel
Cam bolt head needs to be in centre
CORRECT WRONG
!






06
03x
DS
Glue
Pre-Assembly
Detail 2
Detail 2
Detail 2
Detail 1
Detail 1
Detail 3
Detail 3
Detail 3
Detail 1
Detail 1
Detail 1
03x
O
Plastic Foot 12x15mm
03x
M
Metal Support
07x
G
Detail 1 Detail 3
G
S
SEC/AY/12/19/HN1
Flat Head Screw
O3,5x10mm Dowel O5x25mm
M
D
Detail 2
O
C
PRE-DRILLED HOLE
03x
C
Nail 10x10mm
1
2
5
ITM/D523-