Seconique Furniture TORTILLA COFFEE TABLE 54998 User manual

DO NOT
USE
!
PAGE 1
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped o ffimmediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
CARE AND MAINTENANCE
FOR DOMESTIC USE ONLY
SEC/SH/10/21/PJ1
54998
TORTILLA COFFEE TABLE
ASSEMBLY INSTRUCTIONS

Table Leg (yellow marking)Table Leg (yellow marking)
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
S300-301-027-PJ1-01 Table Top 11/2
Frame Side
Table Leg (Red Marking)
S300-301-027-PJ1-02
S300-301-027-PJ1-03
4
2
2
2/2
2/2
2/2
S300-301-027-PJ1-04
Table Leg
5S300-301-027-PJ1-05
Short Frame Side 2
2/2
GLUE
Ø4,0 x 40CP
1/+ 1/+
1/+
TOOLS REQUIRED
A08
E01
B08
HARDWARE LIST
PAGE 2
PARTS LIST
C01
1/+
Ø7,0x110
to help identify them during assembly.
Please Note:
The below parts have been number/colour coded
to help identify them during assembly.
1
2
2
3
3
4
4
5
5
Wooden Cap
F08
08
D
Ø8,0x50
SEC/SH/10/21/PJ1

D
2x
2x
2 - x2
FRAME SIDE
4 -
x2
TABLE LEG (RED MARKING)
5 -
x2
TABLE LEG
B
Detail 2
PARTS REQUIRED
STEP 2
HARDWARE REQUIRED
2 - x2
FRAME SIDE
3 - SHORT FRAME SIDE
STEP 1
PARTS REQUIRED
PAGE 3
x2
TOOLS REQUIRED
Detail 2
Detail 1
(Blue Marking)
5
4
2
(Red Marking)
Detail 5
E
GLUE
Detail 1
E01
GLUE
HARDWARE REQUIRED
TOOLS REQUIRED
Ø7,0x110
B04
SEC/SH/10/21/PJ1
2
3
Detail 5
Detail 5
Ø8,0x50
E01
GLUE
D08
Detail 5
Detail 5
2x
Detail 2
Detail 1

PAGE 4
SEC/SH/10/21/PJ1
STEP 3
STEP 4
E
GLUE
Detail 3
3 - x2
SHORT FRAME SIDE
PARTS REQUIRED
E01
GLUE
HARDWARE REQUIRED
TOOLS REQUIRED
Ø7,0x110
B04
B
Detail 2
Detail 3
Detail 2
3
3
Detail 3
Detail 3
Detail 3
Detail 2
Detail 2
Detail 2
F
XXXXXPJ
CENTRALIZE
Detail 3
Detail 4
1 - x1
TABLE TOP
PARTS REQUIRED
HARDWARE REQUIRED
A08
Ø4,0 x 40CP
TOOLS REQUIRED
F08
Wooden Cap
A
Detail 3 Detail 4
1