Seconique Furniture STOCKHOLM 5 DRAWER NARROW CHEST User manual

STOCKHOLM 5 DRAWER NARROW CHEST
ASSEMBLY INSTRUCTIONS
SEC/SH/10/18/EU1
DO NOT
USE
FOR DOMESTIC USE ONLY
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF
SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS SAFE ASSEMBLY AND
PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE
FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS
PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY HAVE AND
COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE
NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME TO TIME. THIS IS
COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET)
DO NOT USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A
PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT MARKING.
PAGE 1

PAGE 2
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF THE CAM
LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO THE
NARROW PART CLOSES OVER THE BOLT.
SEC/SH/10/18/EU1

3
3
4
4
1
2
1
2
5
6
7
8
9
10
11
12
13
14
15
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PART LIST
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START ASSEMBLING. IF
YOU DO FIND THAT SOMETHING IS MISSING, DO NOT CONTINUE ASSEMBLY, PLEASE CONTACT
YOUR SUPPLIER IMMEDIATELY.
PART LIST
1PILLAR LEG_LEFT 2 PCS
PILLAR LEG_RIGHT 2 PCS
2 PCS
2 PCS
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
5 PCS
5 PCS
5 PCS
5 PCS
5 PCS
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SUPPORT LEG_FRONT & BACK
SUPPORT LEG_LEFT & RIGHT
SIDE PANEL_LEFT
FRONT CROSSBAR
SIDE PANEL_RIGHT
BOTTOM PANEL
BACK PANEL
TOP PANEL
DRAWER BACK
DRAWER SIDE_LEFT
DRAWER SIDE_RIGHT
DRAWER FRONT
DRAWER BASE
PAGE 3
SEC/SH/10/18/EU1

X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
HARDWARE LIST
DOWEL 6 X 30MM 70 PCS
BOLT M7 X 60MM 4 PCS
SCREW M3.5 X 12MM 60 PCS
M6 X 50MM 8 PCS
HANDLE SCREW 19MM 10 PCS
ALLEN KEY 1 PC
CAM BOLT+CAM NUT 16 SETS
PVC GLIDE 4 PCS
SCREW M3.5 X 16MM 30 PCS
HANDLE 5 PCS
FLANGE NUT 4 PCS
SPANNER 1 PC
DRAWER RUNNER A-L/R 10 PCS
DRAWER RUNNER B - L/R 10 PCS
PLASTIC CORNER BLOCK 6 SETS
SCREW M4 X 38MM 10 PCS
Anti-Tip Strap
M4 X 16MM
2 PCS
2 PCS
A
B
C
D
E
F
G
H
I
J
L
M
N
O
P
K
Q
R
PAGE 4
SEC/SH/10/18/EU1

3
3
3
3
4
4
2
2
1
1
1
2
1
2
HARDWARE NEEDED:
B4PCS
G 1PC
M1PC
L4PCS
I
3
A
A
3
1
3
B
G
M
L
3
2
STEP 2
20PCS
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 1 HARDWARE NEEDED:
I
A
4PCS
A
4
4
4
STEP 1.1
STEP 1.2
PAGE 5
SEC/SH/10/18/EU1

HARDWARE NEEDED:
A8PCS
C 40PCS
H4PCS
O
Upper Second Hole
Last Third Hole
First Hole
SCREW MUST BE INSERTED
IN THE FIRST HOLE ON THE
DRAWER RUNNER
O
C
5
H
A
5
10PCS
5&7
5
H
6
H
HARDWARE NEEDED:
A
H
2PCS
2PCS
A
6
6
Upper Second Hole
Last Third Hole First Hole
SCREW MUST BE INSERTED
IN THE FIRST HOLE ON THE
DRAWER RUNNER
C
O
7
A
7
H4PCS
10
7
10
H
STEP 4
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 3
2PCS
STEP 4.1
5
H
7
H
PAGE 6
SEC/SH/10/18/EU1
MAKE SURE THE ARROW ON
THE CAM LOCK IS POINTING
TOWARD THE HOLE ON THE
EDGE OF THE PANEL.
MAKE SURE THE ARROW ON
THE CAM LOCK IS POINTING
TOWARD THE HOLE ON THE
EDGE OF THE PANEL.

H
5
7
6
E
G
HARDWARE NEEDED:
E4PCS
G 1PC
7
5
8
8
7
A
ROUND EDGE
FACING UP
E
G
1
3
8
A
9
7
HARDWARE NEEDED:
E4PCS
G 1PC
34
2
1
8
8
7
5
9
7
5
FINISHED
FRONT EDGE
H
A
6
7
STEP 6
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 5
STEP 6.1STEP 5.1
PAGE 7
SEC/SH/10/18/EU1

H
A
10
7
9
H
9
N
ROUND EDGE
10
9
7
5
HARDWARE NEEDED:
N6SETS
10
9
7
12&13
H
A
11
A
HARDWARE NEEDED:
A
H
11
40PCS
10PCS
12
13
H10PCS
14
14
H
12&13
STEP 8
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 7
STEP 7.1
DRAWER X 5
STEP 8.1
STEP 8.2
PAGE 8
SEC/SH/10/18/EU1
MAKE SURE THE ARROW ON
THE CAM LOCK IS POINTING
TOWARD THE HOLE ON THE
EDGE OF THE PANEL.

D
D
12
11
FINISHED
FRONT EDGE
11
13
12
10PCS
HARDWARE NEEDED:
C20PCS
12
14
H
12
13
14
11
F
K
14
F
K5PCS
10PCS
14
11
C
13
15
15
12 11
J 30PCS
P
15
13
11
J
P
LAST THIRD HOLE
THIRD HOLE
P
10PCS
11
15
13
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 9
DRAWER X 5
STEP 9.1
STEP 9.2
STEP 9.3
STEP 9.4
PAGE 9
SEC/SH/10/18/EU1

X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 10
Serious or fatal injuries can occur from furniture
tipping over. To prevent the furniture from tipping
over we recommend that it is permanently fixed
to the wall.
Wall fixing are not supplied with this product as
different wall material required different types of
fixing devices. Please make sure you use fixing
suitable for the walls in your home.
Wall
Top
WARNING
Q
Q
R
Top
Wall
Top
HARDWARE LIST
(Q) Anti-Tip Strap - 2pcs
(R) M4 X 16MM - 2pcs
PAGE 10
SEC/SH/10/18/EU1