Seconique Furniture CHARLES 3 DRAWER BEDSIDE CHEST User manual

OAK EFFECT VENEER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME. THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE. DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
CHARLES 3 DRAWER BEDSIDE CHEST
ASSEMBLY INSTRUCTIONS
Page 01
SEC/SH/02/22/EU1
DO NOT
USE
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
FOR DOMESTIC USE ONLY

PART LIST
Part Number Part Code Part Description Quantity Carton
1
2
3
4
5
6
Base Frame Horizontal
Left Side Panel
Top Frame (Back)
Top Frame (Front)
Back Frame Horizontal
11/1
1
1
1
7
8
Right Side Panel
Base Frame Vertical
Page 02
SEC/SH/02/22/EU1
9
10
11
12
13
Top Panel
14
Drawer Side - Left
Drawer Base
Drawer Front
Drawer Side - Right
Drawer Back
1
1
1
3
Back Panel
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1
1
1
S100-103-046-EU1-01
S100-103-046-EU1-02
S100-103-046-EU1-03
7
9
8
13
14
3
3
3
3
3
4
5
2
6
10
12
11
S100-103-046-EU1-04
S100-103-046-EU1-05
S100-103-046-EU1-06
S100-103-046-EU1-07
S100-103-046-EU1-08
S100-103-046-EU1-09
S100-103-046-EU1-10
S100-103-046-EU1-11
S100-103-046-EU1-12
S100-103-046-EU1-13
S100-103-046-EU1-14

HARDWARE LIST
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
THE CAM LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.
Page 03
SEC/SH/02/22/EU1
A
B
C
D
E
F
G
H
I
DOWEL 6 X 30MM
BOLT M7 X 60MM
DRAWER RUNNER A (L&R)
HANDLE
CAM BOLT + CAM NUT
TACK
12 PCS
J
L
M
SCREW M4 X 38MM
34 PCS
3 PCS
K
DRAWER RUNNER B (L&R)
HANDLE SCREW M4 X 30MM
SCREW M4 X 30MM
ALLEN KEY
SCREW M3.5 X 16MM
10 PCS
20 PCS
6 SETS
4 PCS
PLASTIC FOOT (L&R)
6 PCS
46 PCS
6 PCS
6 PCS
1 PC
N
O
ANTI - TIP STRAP
SCREW M4 X 16MM
1 PCS
1 PCS
4 PCS

STEP 1
PARTS REQUIRED
1 - LEFT SIDE PANEL x1
HARDWARE REQUIRED
J24
STEP 2
PARTS REQUIRED
K06
TOOLS REQUIRED
Page 04
SEC/SH/02/22/EU1
7 - RIGHT SIDE PANEL x1
2 - TOP FRAME (FRONT) x1
HARDWARE REQUIRED
A22
TOOLS REQUIRED
3 - TOP FRAME (BACK) x1
4 - BASE FRAME HORIZONTAL x1
A
LAST SECOND HOLE
FIRST HOLE
BACK
FRONT
UP SECOND HOLE
J
K
A
5 - BACK FRAME HORIZONTAL x1
6 - BASE FRAME VERTICAL x1
8 - TOP PANEL x1
3
2
46
5
8
K
J
1
7

Page 05
SEC/SH/02/22/EU1
STEP 3
PARTS REQUIRED
HARDWARE REQUIRED
STEP 4
PARTS REQUIRED
x1
B05
TOOLS REQUIRED
x1
x1
1 - LEFT SIDE PANEL
7 - RIGHT SIDE PANEL
x1
x1
x1
x1
7
1
B
HARDWARE REQUIRED
B05
TOOLS REQUIRED
2 - TOP FRAME (FRONT)
3 - TOP FRAME (BACK)
4 - BASE FRAME HORIZONTAL
5 - BACK FRAME HORIZONTAL
6 - BASE FRAME VERTICAL
2
3
5
6
4
B
1

Page 06
SEC/SH/02/22/EU1
STEP 5
PARTS REQUIRED
STEP 6
PARTS REQUIRED
9 - BACK PANEL x1
x18 - TOP PANEL
TOOLS REQUIRED
TOOLS REQUIRED
BOTTOM
PLEASE INSERT THE BACK
PANEL INTO THE UNIT
HARDWARE REQUIRED
HARDWARE REQUIRED
C04
E08
J04
H04
9
E
J
H
8
1 & 7
FRONT SIDE VIEW
BEFORE FIXING THE TOP
THE TOP PANEL WITH
C
PANEL PLEASE ALIGN
THE FRONT FRAME
9
8

STEP 7
Page 07
SEC/SH/02/22/EU1
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
A12
D12
10 - DRAWER BACK x3
11 - DRAWER SIDE - LEFT x3
12 - DRAWER SIDE - RIGHT x3
13 - DRAWER FRONT x3
G06
A
D
G
G
I
10
12
11
13
13
F03
I06
F
X3
STEP 8
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
13 - DRAWER FRONT x3
G06

STEP 10
Page 08
SEC/SH/02/22/EU1
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
x3
STEP 9
PARTS REQUIRED
14 - DRAWER BASE x3
E
14
HARDWARE REQUIRED
TOOLS REQUIRED
J18
L06
E12
x3
X3
J
L

Page 08
SEC/SH/02/22/EU1
STEP 10
PART REQUIRED
O
01
HARDWARE REQUIRED
N
01
TOOLS REQUIRED
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
WARNING
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
N
O
TOP
WALL
TOP TOP
WALL
N