Seconique BLACK WOOD GRAIN LISBON BLANKET BOX User manual

BLACK WOOD GRAIN
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF
SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS SAFE ASSEMBLY AND
PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE
FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS
PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY HAVE AND
COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE
NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME TO TIME. THIS IS
COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET)
DO NOT USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A
PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT MARKING.
FOR DOMESTIC USE ONLY
IMPORTANT
LISBON BLANKET BOX
ASSEMBLY INSTRUCTIONS
SEC/SH/01/21/EU2
Page 01
DO NOT
USE

6
4
1
3
2
5
PART LIST
Page 02
2
3
4
5
6Cushion
Right Side Panel
Left Side Panel
Back Panel
Front Panel 1
1
1
1
1
1/1
1/1
1/1
1/1
1/1
S100-104-004-EU1-02
S100-104-004-EU1-03
S100-104-004-EU1-04
S100-104-004-EU1-05
S100-104-004-EU1-06
Part Number Part Code Part Description Quantity Carton
1S100-104-004-EU1-01 Bottom Panel 11/1
SEC/SH/01/21/EU2

HARDWARE LIST
A
B
C
D
E
F
G
H
I
DOWEL 6 X 30MM 20 PCS
BOLT M7X 60MM 4 PCS
SCREW M3.5 X 16MM
4 PCS
ALLEN KEY 1 PC
CAM BOLT+CAM NUT 8 SETS
BOLT M6 X 50MM
PLASTIC FOOT
20 PCS
8 PCS
L SHAPE HINGE 2 PCS
HINGE (L&R) 1 SET
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
THE CAM LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.
Page 03
SEC/SH/01/21/EU2

STEP 1
PARTS REQUIRED
1 - BOTTOM PANEL x1
HARDWARE REQUIRED
H
BOTTOM
A12
H08
1
H
A
PARTS REQUIRED
2 - FRONT PANEL x1
HARDWARE REQUIRED
A
H04
STEP 2
04
Page 04
2
SEC/SH/01/21/EU2
TOOLS REQUIRED
TOOLS REQUIRED
A

STEP 3
PARTS REQUIRED
3 - BACK PANEL x1
HARDWARE REQUIRED
PARTS REQUIRED
6 - CUSHION x1
HARDWARE REQUIRED
C
D02
STEP 4
08
H
A
A
H04
04
3
E02
D
C
6
TOOLS REQUIRED
Page 05
SEC/SH/01/21/EU2
TOOLS REQUIRED
C
E