Seconique Panama Console Table User manual

Page 01
PANAMA 1 DRAWER BOOKCASE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
SEC/SH/02/21/PJ1
FOR DOMESTIC USE ONLY

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
2
4
1
3
5
6
7
7
8
9
9
10
11
11
12
13
14
15
16
16 1
2
3
4
5
6
8
9
10
11
14
15
16
16
9
6
7
7
11
12
13
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
S300-306-022-PJ1-01 Right Side Panel 11/1
Le Side Panel
Right Front Upright
Le Front Upright
Top Panel
Drawer Runner
Front Crossbeam
Back Crossbeam
Back Panel
Drawer Front
Drawer Side
Drawer Boom
Drawer Back
Back Panel Strip
Base
S300-306-022-PJ1-02
S300-306-022-PJ1-03
S300-306-022-PJ1-04
S300-306-022-PJ1-05
S300-306-022-PJ1-06
S300-306-022-PJ1-07
S300-306-022-PJ1-08
S300-306-022-PJ1-09
S300-306-022-PJ1-10
S300-306-022-PJ1-11
S300-306-022-PJ1-12
S300-306-022-PJ1-13
S300-306-022-PJ1-14
S300-306-022-PJ1-15
1
1
1
1
2
2
1
2
1
2
1
1
1
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
16 S300-306-022-PJ1-16 Shelf 21/1
Page 02
PARTS LIST
SEC/SH/02/21/PJ1

FITTINGS
F
E
14
02
C
B
A
08
25
32
Ø 8 x 30mm
G02
D08
H06
2x
1x
1x
I01
TOOLS REQUIRED
Page 03
Ø 3,5 x 30mm
Ø 3,0 x 30mm
M4 x 25mm
10x10mm
Ø 3,5 x 16mm
SEC/SH/02/21/PJ1

Page 04
6 - x2
DRAWER RUNNER
STEP 2
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A20
STEP 1
1 - x1
RIGHT SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A10
D08
2 - x1
LEFT SIDE PANEL
A
A
A
A
D
D
D
D
A
AAA
A
D
D
D
D
D
A
Please assemble on
a clean soft surface
to avoid damage.
2
A
A
A
A
A
A
A
A
AA
2x
A
A
2x
Please assemble on
a clean soft surface
to avoid damage.
15
7
8
6
A
A
A
A
A
1
A
Ø 8 x 30mm
7 - x2
FRONT CROSSBEAM
8 - x1
BACK CROSSBEAM
15 - x1
BASE
Ø 8 x 30mm
A
SEC/SH/02/21/PJ1

Page 05
7 - x2
FRONT CROSSBEAM
STEP 4
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B05
STEP 3
1 - x1
RIGHT SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B10
2 - x1
LEFT SIDE PANEL
3 - x1
RIGHT FRONT UPRIGHT
4 - x1
LEFT FRONT UPRIGHT
B
B
3
B
B
4
B2
4
3
1
Ø 3,5 x 30mm
7
15
8
7
15
7
8 - x1
BACK CROSSBEAM
Ø 3,5 x 30mm
B
15
15 - x1
BASE
B
B
6
6
6 - x2
DRAWER RUNNER
B
B
B
B
B
B
B
B
B
B
B
B
B
SEC/SH/02/21/PJ1
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.

Page 06
5 - x1
TOP PANEL
STEP 6
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B04
STEP 5
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B06
Ø 3,5 x 30mm
Ø 3,5 x 30mm
B
B
B
BB
B
B
B
B
B
SEC/SH/02/21/PJ1
1
5
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
B
B

Page 07
10 - x1
DRAWER FRONT
STEP 8
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
C08
E02
STEP 7
9 - x2
BACK PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
F14
H06
14 - x1
BACK PANEL STRIP
For your future
reference
order number
should be here
F
F
F
F
F
F
XXXXX
HH
11 - x1
DRAWER SIDE
12 - x1
DRAWER BOTTOM
13 - x1
DRAWER BACK
G02 C
E
E
G
G
9
9
14
10x10mm
Ø 3,5 x 16mm
Ø 3,0 x 30mm
M4 x 25mm
10
11
11
12
13
FFF
F
F
F
F
F
F
FF
FF
F
H
H
H
H
H
H
C
CC
C
C
C
C
SEC/SH/02/21/PJ1
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.

Page 08
STEP 10
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
I01
STEP 9
16 - x2
SHELF
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A02
Serious or fatal injuries can occur from furniture tipping
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.
Please make sure you use fixings suitable for the walls in your home.
A
A
A
16
16
Ø 8 x 30mm
Wall
Top
Top
Wall Top
2x
1x
1x
SEC/SH/02/21/PJ1