Seconique PANAMA 1 DRAWER COFFEE TABLE User manual

PANAMA 1 DRAWER COFFEE TABLE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
FOR DOMESTIC USE ONLY
SEC/SH/02/21/PJ1
Page 01

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
4
4
4
4
1
2
3
3
5
6
7
8
9
9
10
11
Part Code
Part Number Part Description Quantity Carton
01
02
03
04
05
06
07
08
09
10
11
S300-301-024-PJ1-01 Front Frame 11/1
Back Panel
Side Panel
Leg
Top Panel
Right Drawer Runner
Le Drawer Runner
Drawer Front
Drawer Side
Drawer Back
S300-301-024-PJ1-02
S300-301-024-PJ1-03
S300-301-024-PJ1-04
S300-301-024-PJ1-05
S300-301-024-PJ1-06
S300-301-024-PJ1-07
S300-301-024-PJ1-08
S300-301-024-PJ1-09
S300-301-024-PJ1-10
S300-301-024-PJ1-11
1
2
4
1
1
1
1
2
1
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Drawer Boom
PARTS LIST
SEC/SH/02/21/PJ1
Page 02

FITTINGS
TOOLS REQUIRED
Page 03
FITTINGS
SEC/SH/02/21/PJ1
Ø 3,5 x 35mm
C
B
A
08
30
34
Ø 8 x 30mm
Ø 3,0 x 30mm
E 01
D01
M4 x 25mm

Page 04
SEC/SH/02/21/PJ1
3 - x2
SIDE PANEL
STEP 2
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A18
STEP 1
1 - x1
FRONT FRAME
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A14
2 - x1
BACK PANEL
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
A
Ø 8 x 30mm
6 - x1
RIGHT DRAWER RUNNER
7 - x1
LEFT DRAWER RUNNER
Ø 8 x 30mm
A
A
A
A
A
A
A
A
A
A
A
AA
A
A
1
2
2x
A
A
A
A
A
A
A
A
A
A
A
A
A
A
3
6
7

Ø 3,5 x 35mm
Page 05
SEC/SH/02/21/PJ1
3 - x2
SIDE PANEL
STEP 4
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 3
1 - x1
FRONT FRAME
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B08
2 - x1
BACK PANEL
4 - x4
LEG
BB
BB
B
B
B
B
B
B
B
B
BB
6 - x1
RIGHT DRAWER RUNNER
7 - x1
LEFT DRAWER RUNNER
Ø 3,5 x 35mm
B06
B
Please assemble on
a clean soft surface
to avoid damage.
B
B
4
4
2
4
4
1
Please assemble on
a clean soft surface
to avoid damage.
3
7
63

Ø 3,5 x 35mm
B06
Page 06
SEC/SH/02/21/PJ1
5 - x1
TOP PANEL
STEP 6
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 5
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B
B
BB
B
B
Please assemble on
a clean soft surface
to avoid damage.
B
B
B
BB
B
B
B
B
Please assemble on
a clean soft surface
to avoid damage.
Ø 3,5 x 35mm
B10
B
B
5

Ø 3,0 x 30mm
Page 07
SEC/SH/02/21/PJ1
STEP 8
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
STEP 7
8 - x1
DRAWER FRONT
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
C08
D01
9 - x2
DRAWER SIDE
10 - x1
DRAWER BOTTOM
11 - x1
DRAWER BACK
C
D
E
Please assemble on
a clean soft surface
to avoid damage.
9
9
8
11
10
A
Please assemble on
a clean soft surface
to avoid damage.
A
A
E01
M4 x 25mm
A02
Ø 8 x 30mm
C
CC
C
C
C
C
For your future reference
order number should be here