Seconique Corona User manual

ASSEMBLY INSTRUCTIONS
SPD 01207TB
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
PAGE 1
CORONA EXTENDING TABLE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
CARE AND MAINTENANCE
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
SEC/WG/04/15

GLUE
PAGE 2
FITTINGS
PARTS LIST
part
number
name of
part quantity
1Table Top Panel
Table Leg (yellow marking)
2
2
2 1
3
Table Leg (blue marking)
Short frame side
2
4
2
part
number
name of
part quantity
7
Long frame side
Table Crossbar Support
2
part
number
name of
part quantity
* Use of power tools to assemble this product will invalidate
any claim and could damage this product making it unsafe!!!
* Please assemble on a clean soft surface to avoid damage.
* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging parts during assembly.
2,5m x 3m
1
2
1
4
5
5
6
6
7
7
3
3
4
08
08
B
A
Ø7 x 100mm
Ø7 x 60mm
Ø10 x 50mm
06
C
08
08
E
D
Ø8 x 20mm
04
F
16
02
H
G
Ø3,5 x 20mm
4 mm
01
I
Table Centre Panel 5
6 2
X4
SEC/WG/04/15

ADD GLUE
5
5
A= 04
I= 01
GLUE
H= 01
03
02
BLUE x02
YELLOW
ADD GLUE
GLUE
A= 04
I= 01
H= 01
01
6
4
3
PAGE 3
D
GLUE
C
C
C
C
C
C
D
D
D
A
A
A
A
A
A
D
C
C
GLUE
GLUE
D= 04
C= 06
GLUE
H= 01
1
1
2
2
1
04
SEC/WG/04/15

G
E
F
05 06
E= 08
G= 16
F= 04
WHEN FITTING THE TABLE GUIDES
(E) CAREFULLY LINE UP THE
SCREW (G) WITH THE PRE-MARKED
HOLES ON THE TABLE TOP PANEL,
THIS WILL ENSURE THE TABLE
WILL OPEN CORRECTLY WHEN THE
TABLE REQUIRES EXTENDING.
G
E
E
STEP 1 STEP 2 STEP 3
X8
X4
PAGE 4
B= 08
I= 01
D= 04
GLUE
H= 01
D
D
GLUE
SEC/WG/04/15