Seconique CAMBOURNE 54479 User manual

SEC/SH/04/21/FZ1
PAGE 1
CAMBOURNE DESK & BOOKCASE
ASSEMBLY INSTRUCTIONS
54479
FOR DOMESTIC USE ONLY
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF
SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS SAFE ASSEMBLY AND
PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE FITTING
KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS PRODUCT.
ITS USE WILL INVALIDATE ANY CLAIM YOU MAY HAVE AND COULD MAKE THIS
PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE
NECESSARY TO TIGHTEN UP THE FIXING FROM TIME TO TIME. THIS IS
COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXINGS.
FOR CLEANING YOU MAY USE A DAMP CLOTH (NOT WET). DO NOT USE POLISH,
DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A PLACE
MAT UNDER HOT OR COLD ITEMS TO PREVENT MARKING.

F2
L1
Mini Fix 15mm 34
Sets
6
N1 Allen Key 1
YMini Fix Plastic Cap 34
D6
HARDWARE ITEM QTY
Wood Dowel 8 x 25mm 32
Leg Pin
12
5
5
5
5
5
4
3
6
PART LIST
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING.
IF YOU DO FIND THAT SOMETHING IS MISSING, DO NOT CONTINUE ASSEMBLY.
PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
NOT PROVIDED
1Book-Side Panel (L) 1
2Book-Side Panel (R) 1
3Side Panel 1
4Top Panel 1
5Shelf Panel 5
6Big Crossbar 2
7Small Crossbar 1
USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE
PART LIST
SEC/SH/04/21/FZ1
PAGE 2
A7
E20
A33
Strap
Wood Screw 3.5 x 30mm
Washer
HARDWARE ITEM FOR ANTI-TIP QTY
1
1
2
7

1st
3rd
Lock
2nd Insert
Right position
Y
STEP 1 STEP 2
STEP 4 STEP 5
Assemble the panel no. 4 with Mini Fix 15mm
(F2) & button the Mini Fix Cam by using Mini Fix
Cap (Y). Use Allen Key to tighten the Mini Fix
Cap (F2).
Assemble 5pcs of panel no. 5 together with panel no. 2 by using Mini Fix 15mm (F2) & button the Mini Fix Cam
(F2) by using Mini Fix Cap (Y).
Y
YY
Y
Y
STEP 3 Assemble the panel no. 3, 6 & 7 together with
Mini Fix 15mm (F2) & button the Mini Fix Cam
(F2) by using Mini Fix Cap (Y). Use Allen Key
(N1) to tighten the Mini Fix 15mm (F2).
F2
F2
F2
D6
D6 D6
D6
D6
D6
D6
D6
F2
F2
D6
5
5 pcs
7
3
4
6
2 pcs
Fix the Mini Fix Bolt (F2) at panel no. 3, 4 & 7.
Insert the Mini Fix Cam (F2) at all panel below.
Insert the Wood Dowel 8 x 25mm
(D6) at panel no. 3, 4, 5, 6 & 7.
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
F2
2
1
Fix the Mini Fix Bolt (F2) at panel 1 & 2.
3
6
6
7
Y
N1
1st
3rd
Lock
2nd Insert
Right position
F2
F2
Y
F2
Y
Y
Y
4
1st
3rd
Lock
2nd Insert
Right position
F2
F2
Y
N1
F2
F2
Y
N1
2
5
5
5
5
5
Y
F2
F2
F2
F2
F2
F2
Y
PAGE 3
SEC/SH/04/21/FZ1
Y
F2
F2
F2
F2

F2
Y
F2
Y
F2
Y
STEP 6 STEP 7
STEP 8 COMPLETE
Nail the Leg Pin (L1) at bottom of panel no. 1, 2 & 3.
Assemble the table part panel no. 3, 4, 6 & 7 to the unit by using Mini Fix 15mm
(F2) & button the Mini Fix Cam (F2) by using Mini Fix Cap (Y). Use Allen Key
(N1) to tighten the Mini Fix 15mm (F2).
Assemble the panel no. 1 to the unit with Mini Fix 15mm (F2) & button the Mini
Fix Cam (F2) by using Mini Fix Cap (Y). Use Allen Key (N1) to tighten the Mini
Fix 15mm (F2).
Finally, stand up the product properly.
Y
Y
1st
3rd
Lock
2nd Insert
Right position
3
4
7
F2
F2
Y
N1
Y
Y
Y
YYY
Y
1
1
5
1st
3rd
Lock
2nd Insert
Right position
F2
3
1
2
5
5
5
5
5
4
6
6
Hit
Softly
L1
L1
L1
L1
L1
L1
L1
Stand
Up
1
3
2
Y
Y
PAGE 4
SEC/SH/04/21/FZ1

PAGE 5
SEC/SH/04/21/FZ1
30