Seconique RIO TABLE User manual

ASSEMBLY INSTRUCTIONS
SPD 01201TB
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
PAGE 1
RIO TABLE
SEC/WG/04/15
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
CARE AND MAINTENANCE
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER

08
GLUE
02
08
D
B
A
C
PAGE 2
FITTINGS
PARTS LIST
part
number
name of
part quantity
1Table Top
Table Leg (blue marking)
1
2 2
3
Table Leg (yellow marking)
Frame Side
2
4 4
part
number
name of
part quantity
7,0 x 80
4,0 x 35
01
* Use of power tools to assemble this product will invalidate
any claim and could damage this product making it unsafe!!!
* Please assemble on a clean soft surface to avoid damage.
* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging parts during assembly.
2,5m x 3m
SEC/WG/04/15
04
03 03
03
04
04
04
02
02
01

02
03
04 ADD GLUE
GLUE
04
04
ADD GLUE
GLUE
A =01
C = 02
D = 01
01
A =01
C = 04
D = 01
03 04
B = 08
GLUE
A =01
C = 02
D = 01
02
YELLOW
BLUE
FOR YOUR FUTURE
REFERENCE
SPD NUMBER
SHOULD BE HERE
SPD 00340T
CENTRALIZE
03
02
YELLOW
04 ADD GLUE
BLUE
SEC/WG/04/15
PAGE 3

IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
CARE AND MAINTENANCE
PAGE 1
ASSEMBLY INSTRUCTIONS
SPD 01201TB
RIO CHAIR
SEC/WG/04/15

08
04
GLUE
02
04
BD
E
AC
PAGE 2
PARTS REQUIRED PER A CHAIR
part
number
name of
part quantity
1Right chair side
Left chair side
1
2 1
3Chair seat
Back rail
1
4 2
part
number
name of
part quantity
5Seat rail 2
part
number
name of
part quantity
04
04
02
01
05
05
8,0 x 30 7,0 x 60
4,0 x 35
01
* Use of power tools to assemble this product will invalidate
any claim and could damage this product making it unsafe!!!
* Please assemble on a clean soft surface to avoid damage.
* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging parts during assembly.
2,5m x 3m
03
SEC/WG/04/15
FITTINGS REQUIRED PER A CHAIR

SEC/WG/04/15
01
GLUE
B =02
A =01
D = 04
E = 01
GLUE
B =02
A =01
D = 04
E = 01
C = 04
04
03
04
04
02
01
05
05
02
GLUE
B
A
GLUE
B
A
D
E
D
E
PAGE 3
A B
Glue must be added to
the dowel holes on
parts 2 and 4
A B
Glue must be added to
the dowel holes on
parts 1 and 4
03
CENTRALIZE
C
D
D
D
D
D
D
D
D
C
C
C
C