Seconique Lisbon Blanket Box 100-104-005 User manual

LISBON BLANKET BOX
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF
SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS SAFE ASSEMBLY AND
PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE
FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS
PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY HAVE AND
COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE
NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME TO TIME. THIS IS
COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET)
DO NOT USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A
PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT MARKING.
SEC/SH/10/18/EU1
PAGE 1
FOR DOMESTIC USE ONLY
DO NOT
USE

PAGE 2
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW ON THE CAM
LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO THE
NARROW PART CLOSES OVER THE BOLT.
SEC/SH/10/18/EU1

1PC
CUSHION
BOTTOM PANEL
RIGHT SIDE PANEL
FRONT PANEL
BACK PANEL
LEFT SIDE PANEL
1
2
3
5
4
6
1
2
3
4
6
5
PAGE 3
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START ASSEMBLING. IF
YOU DO FIND THAT SOMETHING IS MISSING, DO NOT CONTINUE ASSEMBLY, PLEASE CONTACT
YOUR SUPPLIER IMMEDIATELY.
PARTS LIST
SEC/SH/10/18/EU1
1PC
1PC
1PC
1PC
1PC

H4PCS
A
1
1
HARDWARE NEEDED:
A
H8PCS
16PCS
H
1
MAKE SURE THE ARROW ON
THE CAM LOCK IS POINTING
TOWARD THE HOLE ON THE
EDGE OF THE PANEL.
BOTTOM
H2
2
A
2
PAGE 4
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
HARDWARE LIST
A
B
C
D
E
F
G
H
I
DOWEL 6x30MM 20 PCS
BOLT M7x60MM 4 PCS
SCREW M3.5x16MM
4 PCS
ALLEN KEY 1 PC
CAM BOLT+CAM NUT 8 SETS
BOLT M6x50MM
PVC FOOT CENTRE
20 PCS
8 PCS
L SHAPE HINGE 2 PCS
HINGE 1 SET
STEP 1
STEP 1.1
SEC/SH/10/18/EU1

HARDWARE NEEDED:
A
H4PCS
4PCS
A
3
H3
3
8PCS
C
1SET
E
D2PCS
C
D
6
6
E
C
6
H
H
A
3
2
1
2
1
HARDWARE NEEDED:
B4PCS
F1PC
I
F
A
5
4
1
2
33
1
5
2PCS
I
B
F
STEP 3
STEP 2
PAGE 5
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 2.1 STEP 3.1
SEC/SH/10/18/EU1
X8

D
C
3
2
1
6
6
3
HARDWARE NEEDED:
4PCS
C
4&5 E
C4
5
HARDWARE NEEDED:
B4PCS
C
4
2
1
F
G
1PC
8PCS
4PCS
C
G
5
5
33
B
2PCS
I
STEP 4
PAGE 6
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 4.1
STEP 5
STEP 5.1
I
F
B
F
SEC/SH/10/18/EU1