Seconique MALVERN User manual

DO NOT
USE
MALVERN 4 DRAWER CHEST
ASSEMBLY INSTRUCTIONS
Page 01
IMPORTANT
FOR DOMESTIC USE ONLY
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME. THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE. DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
SEC/SH/07/23/EU1

S100-102-169-EU1-04
PART LIST
Page 02
Part Number Part Code Part Description Quantity Carton
111/1
2
3
Side Panel - Left
4
Base Apron 2
5
1
6
7
Back Panel
8
Bottom Panel
4
9
10
Drawer Back
Drawer Side - Left
Drawer Side - Right
Drawer Front
Top Panel
Crossbar
4
4
4
1
2
1
3
11
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Drawer Base 4
12 1/1
Side Panel - Right
SEC/SH/07/23/EU1
Drawer Bottom Support Rail 4
13 1/1
1
7
3
2
2
2
6
5
5
4
8
8
9
10 12
11
13
14
14 1/1
Top Crossbar 1
S100-102-169-EU1-01
S100-102-169-EU1-02
S100-102-169-EU1-03
S100-102-169-EU1-05
S100-102-169-EU1-06
S100-102-169-EU1-07
S100-102-169-EU1-08
S100-102-169-EU1-09
S100-102-169-EU1-10
S100-102-169-EU1-11
S100-102-169-EU1-12
S100-102-169-EU1-13
S100-102-169-EU1-14

HARDWARE LIST
Page 03
A
B
C
D
E
F
G
H
I
DOWEL 6 X 30MM 60 PCS
DRAWER RUNNER A - L/R
64 PCS
CAM BOLT + CAM NUT
8 PCS
SCREW M3.5 X 16MM 28 PCS
TACK 32 PCS
J
K
DRAWER RUNNER B - L/R
SCREW M3.5 X 12MM
PLASTIC FOOT
ALLEN KEY
4 PCS
24 SETS
8 PCS
1 PC
SCREW M4 X 38MM
BOLT M6 X 50MM
SEC/SH/07/23/EU1
8 PCS
8 PCS
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - USE A CROSS SLOT SCREWDRIVER TO TIGHTEN THE CAM BOLT INTO THE HOLE.
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
THE CAM LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.
LPLASTIC H STRIP 1 PC
ANTI - TIP STRAP
SCREW M4 X 16MM
M
N
O
8 PCS
2 PCS
2 PCS
SCREW M4 X 25MM

STEP 1
PARTS REQUIRED
1 - SIDE PANEL - LEFT x1
HARDWARE REQUIRED
A02
STEP 2
Page 04
TOOLS REQUIRED
FRONT BACK
UP SECOND HOLE
LAST THIRD HOLE
FIRST HOLE
PARTS REQUIRED
6 - SIDE PANEL - RIGHT x1
HARDWARE REQUIRED
FRONTBACK
UP SECOND HOLE
LAST THIRD HOLE FIRST HOLE
SEC/SH/07/23/EU1
I04
A02
TOOLS REQUIRED
I04
G
I
H
G
I
H
G
A
H
H
A
G
A
H
H
H
H
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
H
H
H
H
A
1
H02
H04
G16
G16
H02
H04
6

STEP 3
STEP 4
Page 05
A
SEC/SH/07/23/EU1
PARTS REQUIRED
2 - CROSSBAR x3
HARDWARE REQUIRED
A20
TOOLS REQUIRED
H08
3 - TOP CROSSBAR x1
PARTS REQUIRED
4 - BOTTOM PANEL x1
HARDWARE REQUIRED
A04
TOOLS REQUIRED
H04
7 - TOP PANEL x1
H
A
H
7
4
A
A
A
H
H
H
AAAA
A
A
A
AA
A
A
AAA
A
A
A
A
HH H
HHHH
2 2 2 3
55
5 - BASE APRON x2

STEP 5
STEP 6
Page 06
SEC/SH/07/23/EU1
PARTS REQUIRED
1 - SIDE PANEL - LEFT x1
2 - CROSSBAR x3
HARDWARE REQUIRED
TOOLS REQUIRED
PARTS REQUIRED
4 - BOTTOM PANEL x1
5 - BASE APRON x2
HARDWARE REQUIRED
C04
TOOLS REQUIRED
H
1
3
2
2
2
3 - TOP CROSSBAR x1
C
5
5
4
C
C

STEP 7
STEP 8
Page 07
SEC/SH/07/23/EU1
PARTS REQUIRED
6 - SIDE PANEL - RIGHT x1
HARDWARE REQUIRED
C04
TOOLS REQUIRED
PARTS REQUIRED
7 - TOP PANEL x1
HARDWARE REQUIRED
D04
F04
TOOLS REQUIRED
C
6
C
C
C
H
F
D
7
D
F
D
F
D
F
H

STEP 9
STEP 10
PARTS REQUIRED
HARDWARE REQUIRED
A32
TOOLS REQUIRED
9 - DRAWER BACK x4
10 -DRAWER SIDE-LEFT x4
12 - DRAWER FRONT x4
11 -DRAWER SIDE-RIGHT x4
K08
H12
Page 08
SEC/SH/07/23/EU1
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
8 - BACK PANEL x2
32
E
H
9
K
A
H
A
A
A
A
A
A
A
H
H
H
12
10
11
L01
X4
X4
H08
LE
E
8
8
K
O
P

STEP 11
STEP 12
Page 09
SEC/SH/07/23/EU1
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
D24
H04
X4
PARTS REQUIRED
13 - DRAWER BASE x4
HARDWARE REQUIRED
TOOLS REQUIRED
32
G
H
G
14 - DRAWER BOTTOM SUPPORT RAIL x4
M
H
X4
D
J
J08
M08
M
G
G
D
D
D
D
D
13
X4
X4
12
14
X4
X4

STEP 13
STEP 14
Page 10
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
SEC/SH/07/23/EU1
PARTS REQUIRED
WARNING
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
O
TOP
TOP
WALL
N
WALL
TOP
O
02
HARDWARE REQUIRED
N
02
TOOLS REQUIRED
N
X4