hygena 656/4966 User manual

Pair of Bentwood Chairs
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 45cm
Depth - 48.5cm
Height - 86.5cm
If you need help or have damaged or missing parts, call the Customer Helpline:08456 400800
656/4966
Issue 2 - 22/03/10
656/4973
656/4980
658/7053
658/9800

1
Safety and Care Advice
Dispose of all packaging
carefully and responsibly.
-
Please read these instructions fully before starting assembly
Important
This product has been finished using natrual materials. As a living material, you may notice some
variation in the grain and colour shade between the different components.
Solid wood / Real wood veneers
Do not stand or put excessive
weight on the product.
Place the product on flat and
steady surface during use.
Keep this instructions for
future use.
Clean using a damp cloth or a
proprietary domestic furniture
polish. Do not use abrasive
cleaners.
This product should not be
discarded
with household waste.
Take to your local authority waste
disposal only.
Care and maintenance
From time to time check that
there are no loose screws on
this unit.
Unlike a synthetic or man-made material which has a uniform finish, a feature of natural wood is its
variation in grain and colour. We wish to reassure you that this is quite normal and is not the result of
any manufacturing fault.
Where sheets of wood are joined together, a line may be detected. Again, this is normal and is not an
imperfection.
The natural finish should be cared for by the periodic application of a good quality ‘was’ based
domestic furniture polish (Not silicone!!). Occasional / small spills should be removed immediately using
a damp cloth.
Do not allow hot articles to come into contact with the surface, as damage will occur!
Check you have all the
components and tools listed
on page 2 and 3.
Do not use this item if any
components are missing or
damaged.
To ensure an easier assembly,
we strongly advise that all fittings
are only finger tightened during
initial assembly. Only upon
completion of the assembly
should all fixing points be fully
tightened.
A classic characteristic of oak timber is medullary rays. These are natural rays or streaks usually seen
across the grain. These rays have a different cellular structure and reflect light differently to the
surrounding wood. These rays or streaks are a unique characteristic of natural oak and are there not a
defeat.

Please check you have all the panels listed below
Components - Parts
2
2Leg x 2 (65x42cm)
1Seat pad x 2 (41x43cm)
3Leg x 2 (65x42cm)
Hole with thread
Plain hole

Please check you have all the fittings listed below
Components - Fittings
3
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C
DEF
G H
19mm Screw x 2 Spring washer x 14 Spacer x 8
Plastic plug x 8 32mm Screw x 8 Allen key x 2
Bracket x 2 12mm Screw x 4
Small hammer
(for fitting plastic plug)

a: Assemble legs and
together using fixings
and .
Note: Leg has a plain
hole. Leg has a
threaded hole.
Note: Do not fully tighten
fixings at this stage.
b: Slide spacers over
ends of legs.
Note: Ensure larger hole
in spacers is facing up.
Attaching leg frame
Assembly Instructions
Step 1
Step 2
4
A
3
a:
b:
Fitting plastic caps
Fit plastic plugs into
the ends of legs and
as shown.
3
2
2
2
A
B
B
3
CC
C
C
2
D
D
D
D
D
Hole with thread
Plain hole
Shown upside down
3
C
C
2
3

Assembly Instructions
Step 3
5
B
E
B
E
B
E
B
E
1
Attaching seat pad
Place seat pad upside
down onto a clean flat
surface. (edge of table
top)
Ensuring the arrows on the
chair legs are pointing
towards the front of the
chair, attach leg assembly
to underside of seat pad
using fixings and .
Note: Do not fully tighten
fixings at this stage.
EB
1
Table top
Arrows to point fowards
Front
Arrows to
point fowards
1

Assembly Instructions
Step 4
6
H
H
B
H
B
After Assembly
Attaching bracket
Fit bracket to chair
legs using fixings and
.
Note: Do not fully tighten
fixings at this stage.
G
G
G
B
2
3

Assembly Instructions
Step 5
Tightening fixings
Turn the chair upright.
Whilst applying a firm
downward pressure to
ensure the chair is stable,
fully tighten all screws.
Assembly is complete.
If you need help for have damaged or missing parts, call the Customer helpline:08456 400800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW

Bentwood Chair
Dimensions
Width - 49.5cm
Depth - 49.5cm
Height - 83cm
Issue 1 - 15/3/2011
Important - Please read these instructions carefully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions - Please keep for future reference 600/5511

1
Safety and Care Advice
Important - Please read these instructions carefully before starting assembly
• Check you have all the
• Remove all fittings from the
components and tools listed on
page 2.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• The maximum safe weight of
user:110kgs. • Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.