Seconique Panama 100-102-045 User manual

Page 01
PANAMA 6 DRAWER CHEST
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
SEC/SH/02/21/PJ1
FOR DOMESTIC USE ONLY

SEC/SH/02/21/PJ1
Page 02
6x
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
S100-102-045-PJ1-01 Right Side Panel 11/1
Le Side Panel
Right Front Upright
Le Front Upright
Top Panel
Drawer Runner
Top Front Crossbeam
Back Crossbeam
Back Panel
Drawer Front
Drawer Side
Drawer Boom
Drawer Back
Centre Front Upright
Back Upright
S100-102-045-PJ1-02
S100-102-045-PJ1-03
S100-102-045-PJ1-04
S100-102-045-PJ1-05
S100-102-045-PJ1-06
S100-102-045-PJ1-07
S100-102-045-PJ1-08
S100-102-045-PJ1-09
S100-102-045-PJ1-10
S100-102-045-PJ1-11
S100-102-045-PJ1-12
S100-102-045-PJ1-13
S100-102-045-PJ1-14
S100-102-045-PJ1-15
1
1
1
1
6
1
1
2
6
12
6
6
1
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
16
17
S100-102-045-PJ1-16
S100-102-045-PJ1-17
Centre Drawer Runner
Boom Front Crossbeam
31/1
1/1
1
* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
17
6
6
6
6
6
16
16
16
9
11

M4 x 25mm
F10x10mm
E
32
06
Ø 3,5 x 30mm
Ø 8 x 30mm
C
B
A
48
41
66
Ø 3,0 x 30mm
FITTINGS
Ø 3,5 x 16mm
G08
D06
H
2x
1x
1x
01
SEC/SH/02/21/PJ1
TOOLS REQUIRED
Page 03

Page 04
SEC/SH/02/21/PJ1
Ø 8 x 30mm
STEP 2
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A20
7 - x1
TOP FRONT CROSSBEAM
STEP 1
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A24
8 - x1
BACK CROSSBEAM
14 - x1
CENTRE FRONT UPRIGHT
15 - x1
BACK UPRIGHT
16 - x3
CENTRE DRAWER RUNNER
Please assemble on
a clean soft surface
to avoid damage.
A
Ø 8 x 30mm
A
A
66x
7
A
A
A
A
8
A
A
A
A
A
A
A
A
16
3x
17
A
A
A
A
14
15
A
A
A
A
A
A
A
A
6 - x6
DRAWER RUNNER
17 - x1
BOTTOM FRONT CROSSBEAM
Please assemble on
a clean soft surface
to avoid damage.
A

Ø 3,5 x 30mm
Page 05
STEP 3
1 - x1
RIGHT SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B12
2 - x1
LEFT SIDE PANEL
6 - x6
DRAWER RUNNER
SEC/SH/02/21/PJ1
A
Please assemble on
a clean soft surface
to avoid damage.
A
A
A
A
A
Ø 8 x 30mm
A10
B
B
B
B
B
B
B
B
BB
A
A
A
A
A
B
B
2
4
B
B
B
Please assemble on
a clean soft surface
to avoid damage.
1
3
B
B
B
B
STEP 4
1 - x1
RIGHT SIDE PANEL
PARTS REQUIRED
2 - x1
LEFT SIDE PANEL
Ø 3,5 x 30mm
TOOLS REQUIRED
HARDWARE REQUIRED
B06
3 - x1
RIGHT FRONT UPRIGHT
4 - x1
LEFT FRONT UPRIGHT
1
6
6
6
6
6
6
2