Security Camera King HDCV-ELE2MB28 User manual

2MP HDCVI Covert Camera
HDCV-ELE2MB28

Table of Contents
1General Introduction .......................................................................................................................1
1.1 Overview.............................................................................................................................1
1.2 Features..............................................................................................................................1
2Device Structure..............................................................................................................................2
2.1 Dimension ..........................................................................................................................2
2.2 Cable Port ..........................................................................................................................4
3Installation.........................................................................................................................................6
3.4 Installation for model D .................................................................................................10
3.4.1 Installation for Model D1 (with clamping jaw) ...................................................10
4Menu ................................................................................................................................................12
4.1 HCVR Settings ................................................................................................................12
4.2 Menu Operation ..............................................................................................................12
Appendix ⅠMaintenance .....................................................................................................................14
Welcome
Thank you for purchasing our HDCVI camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated DC 12V or AC24V in the IEC60950-1. (Power supply requirement is
subject to the device label).
Please install easy-to-use device for power off before installing wiring, which is for emergent power
off when necessary.
Please check if the power supply meets the requirements of working voltage of the camera before
operating the device (The material and length of the power supply cable will influence terminal
voltage value).
Please prevent the line cord from being trampled or pressed, especially the plug, power socket and
the junction from the device.

2．Environment
Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus.
Please transport, use and store the device within the range of allowed humidity and temperature.
Please do not allow water and other liquid falling into the camera in case that the internal
components are damaged.
Please keep the sound ventilation in case of heat accumulation.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
Please pack the device with standard factory packaging or material with same quality when
transporting the device.
It is recommended to use the device together with lightning protection device to enhance lightning
protection effect.
It is recommended to GND the device to enhance device reliability.
It is advised to use qualified video transmission cable to improve video quality. It is recommended
to use 75-3 coaxial cable or higher standard.
Warning
Please use the standard accessories provided by manufacturer and make sure the device is
installed and fixed by professional engineers.
Please prevent the device surface from the radiation of laser beam when using laser beam device.
Please do not provide two or more power supply modes for the device, otherwise it may cause
damage to the device.
Statement
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly upgraded according to the product update; the upgraded content will
be added in the manual without prior announcement.
Please contact the customer service for the latest procedure and supplementary documentation.
The company is not liable for any loss caused by the operation which is not followed by the manual.
Please refer to the company’s final explanation if there is any doubt or dispute.

1General Introduction
1.1 Overview
This series HDCVI camera conforms to the HDCVI standard. It supports video signal high-
speed long distance transmission without any delay. It can be controlled by the HCVR
conforming to the HDCVI.
1.2 Features
Adopt high performance CMOS image sensor, megapixel definition.
Support coaxial transmission of HD video, audio and control signal.
For 720P series, it supports RG59 coaxial transmission without any loss, the distance is
over 800m, for 1080P series, it supports RG59 coaxial transmission without any loss, the
distance is over 500m.
High speed, long distance real-time transmission.
Support HD/SD video output. (some devices only support HD video output)
Support OSD menu adjusting parameters.
Support auto exposure, AWB, auto electronic gain.
Support true WDR function, the range can reach 120dB (only supported by WDR models)
Support DC 12V power supply.
Pinhole cameras can be applied to covert places such as ATM; mobile cameras can be
applied to places such as bus, school bus and subway etc.
2Device Structure
2.1 Dimension
Refer to Figure 2-6 for the dimension. The unit is mm.
Figure 2-6

2.2 Cable Port
Note
The following figures are for reference only, which are only used to know the function of
cable port.
Different devices may have different cables, please refer to the actual device for more
details.
Please refer to Figure 2-9 for DC 12V power input port.
Figure 2-9
Please refer to Figure 2-10 for video output port.
Figure 2-10
Please refer to Figure 2-11 for audio input port.
Figure 2-11
Please refer to Figure 2-12for HD/SD switch control cable.
Figure 2-12
Note
When the two cables become short circuit, then it can realize from HD video output to SD
video output. On the contrary, it will switch back to HD video output when the two cables
become open circuit.
HD/SD switch control cable is only supported by some models.

Please refer to Figure 2-13 for the mobile aviation port.
Figure 2-13
3Installation
Attention:
Please install the device in time after it is taken apart, which is to avoid the camera
module being exposed to damp environment for too long.
Before the installation, please make sure the installation surface is thick enough to sustain
at least 3X weight of the camera.
For the installation mode of side outlet, make sure the direction of side outlet is in
accordance with that of the installation position map when sticking the installation position
map. Besides, pull the cable through the pedestal cable slot before locking the screw.
Please do not remove the electrostatic adsorption film (if yes) on the surface of
transparent cover before installation and debugging is completed, which is to avoid
damage during installation.
The installation figures below are for reference only.

3.4 Installation for model D
3.4.1 Installation
Figure 3-6
Step 1
Pull the camera ③through the installation board ①according to the cable direction, and then
fix it on the installation board via clamping jaw ②.
Step 2
Paste some glass sealant on the back of the joint between camera and installation board,
which is to fix it more firmly.
Step 3
Connect the device cable to the back-end HCVR device.
For mobile model: Connect aviation head cable to the back-end HCVR device.
For general model: Connect the camera BNC cable to the back-end HCVR device, and
connect the power port to power.
So far, the device installation and cable connection have been completed, you can check
monitoring image via back-end encoding device.

4Menu
4.1 HCVR Settings
This HDCVI camera series can adjust OSD menu via coaxial control. After connected the
camera to the HDCVI series HCVR, from Main Menu->Setting->System->PTZ, you need to
select the channel number for access and set control mode as HDCVI and the protocol as HD-
CVI. Click “Save”button to save current setup. See Figure 4-1.
Figure 4-1
4.2 Menu Operation
Click the right mouse button and select “PTZ Control”, then you will see the “PTZ Setup”menu,
which is as shown in Figure 4-2 and Figure 4-3.
Figure 4-2

Figure 4-3
See Table 4-1 for the details of button functions.
Button
Function
+
Open menu
、
Select menu item
、
Select menu value
Table 4-1
If there is “ ”, click the “Enter”button in “Menu Operation”interface to go to the 2nd menu.
Click “Return” button to go back to the previous menu interface.
Please use a UTC controller or enter the OSD menu for switchover between HD and SD video
output.

Appendix ⅠMaintenance
Caution
Please maintain the device according to the following instructions in order to ensure the image
effect and long-term stable operation of the device.
Maintenance for lens and mirror surface
The lens and mirror surface are covered with antireflection coating, so it may produce
hazardous substance and lead to performance reduction or scratch, dimness etc. when it is
stained with dust, grease, fingerprint and so on, please refer to the following methods to deal
with once dirt is found:
Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth
or paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to
change the cloth and wipe several times if it is not clean enough.
Camera Body Maintenance
Use a soft dry cloth to clean the camera body when it is dirty, in case the dirt is hard to remove,
use a clean dry cloth soaked with mild detergent and wipe gently, make it dry later. Don’t use
volatile solvent like alcohol, benzene, thinner and etc. or strong detergent with abrasiveness,
otherwise it will damage the surface coating or reduce the working performance of the device.
Note
This manual is for reference only. Slight difference may be found in the user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
Please visit our website or contact your local service engineer for more
information.