Security Camera King IPOB-ELS2IR12XA-EP User manual

i
Network Camera Web3.0 Operation Manual
Version 1.0.0E

ii
Table of Contents
1Network Connection...................................................................................................... 1
2Main Interface Introduction............................................................................................ 2
2.1 Log in................................................................................................................ 2
2.2 Live Interface .................................................................................................... 6
2.3 Encode Setup ................................................................................................... 6
2.4 System Menu.................................................................................................... 7
2.5 Video Window Function Option......................................................................... 7
2.6 Video Window Setup......................................................................................... 8
2.6.1 Hide Image Control..................................................................................... 8
2.6.2 Original size................................................................................................ 9
2.6.3 Full screen.................................................................................................. 9
2.6.4 Width and height ratio................................................................................. 9
2.6.5 Fluency Adjustment.................................................................................... 9
2.6.6 Zoom and Focus......................................................................................... 9
2.6.7 Image control............................................................................................ 10
3PTZ Control................................................................................................................. 12
4Playback...................................................................................................................... 15
4.1 Playback Interface .......................................................................................... 15
4.2 Function of Play.............................................................................................. 15
4.3 Date................................................................................................................ 16
4.4 File List ........................................................................................................... 16
4.5 Progress Bar................................................................................................... 18
5Setup........................................................................................................................... 19
5.1 Camera........................................................................................................... 19
5.1.1 Conditions................................................................................................. 19
5.1.2 Video ........................................................................................................ 25
5.1.3 Audio ........................................................................................................ 30
5.2 Network........................................................................................................... 30
5.2.1 TCP/IP...................................................................................................... 30
5.2.2 Connection ............................................................................................... 32
5.2.3 PPPoE...................................................................................................... 34
5.2.4 DDNS ....................................................................................................... 34
5.2.5 IP filter ...................................................................................................... 36
5.2.6 SMTP （e-mail)........................................................................................ 37
5.2.7 UPnP........................................................................................................ 38
5.2.8 SNMP ....................................................................................................... 39
5.2.9 Bonjour ..................................................................................................... 41

iii
5.2.10 Multicast ................................................................................................... 42
5.2.11 WIFI.......................................................................................................... 43
5.2.12 802.1x....................................................................................................... 46
5.2.13 QoS .......................................................................................................... 47
5.2.14 3G............................................................................................................. 48
5.2.14.1 Dialing Setting.................................................................................... 49
5.2.14.2 Mobile Phone ..................................................................................... 50
5.3 Event............................................................................................................... 51
5.3.1 Video detect.............................................................................................. 51
5.3.2 Alarm........................................................................................................ 56
5.3.3 Abnormity ................................................................................................. 58
5.4 Storage........................................................................................................... 61
5.4.1 Record Schedule and Snapshot Schedule ............................................... 61
5.4.2 Destination................................................................................................ 62
5.4.3 Record control .......................................................................................... 63
5.5 System............................................................................................................ 64
5.5.1 General..................................................................................................... 64
5.5.2 Account..................................................................................................... 66
5.5.3 PTZ........................................................................................................... 70
5.5.4 Default...................................................................................................... 71
5.5.5 Import/Export............................................................................................ 72
5.5.6 Auto Maintenance..................................................................................... 72
5.5.7 Upgrade.................................................................................................... 73
5.6 Information...................................................................................................... 73
5.6.1 Version ..................................................................................................... 73
5.6.2 Log............................................................................................................ 74
5.6.3 Online User............................................................................................... 75
6Alarm........................................................................................................................... 76
7Log out ........................................................................................................................ 77

iv
Important
The following functions are for reference only. Some series products may not
support all the functions listed below.

1
1 Network Connection
These series network camera products support the Web access and management via PC.
Web includes several modules: monitor channel preview, PTZ control, system configuration, alarm and
etc.
Please follow the steps listed below for network connection.
Make sure the network camera has connected to the network properly.
Network camera IP address and PC IP address shall be in the same network segment. If there is
router, please set the corresponding gateway and subnet mask.
Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

2
2 Main Interface Introduction
2.1 Log in
Open IE and input network camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address
bar. See Figure 2-1.
Figure 2-1
The login interface is shown as below. See Figure 2-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here

3
Figure 2-2
If it is your first time to login in, you may see the interface shown as in Figure 2-3.
Figure 2-3

4
Click on “Please click here to download and install the plug-in”. The system pops up warning information
to ask you whether run or save this plug-in. See Figure 2-4.
Figure 2-4
You must either run or save the file to local and install it. Follow the following steps. Click on run, you
will see Figure 2-5 and Figure 2-6.

5
Figure 2-5
Figure 2-6

6
When plug-in installation completes, the installation page closes automatically. The web-end will
refresh automatically, and then you can view video captured by the camera.
2.2 Live Interface
After you logged in, you can see the live monitor window. See Figure 2-7
Figure 2-7
There are four sections:
Section 1: Encode setup bar
Section 2: System menu
Section 3: Window function option bar
Section 4: Window adjust bar
2.3 Encode Setup
The encode setup interface is shown as in Figure 2-8.
2
3
1
4

7
Figure 2-8
Please refer to the following sheet for detailed information.
Parameter
Function
Main stream
In normal network width environment, main stream can record
audio/video file and realize network monitor.
You can set the main stream resolution if your device supports.
Sub (Extra)
stream
If network width is not sufficient, you can use sub stream to
realize network monitor.
Protocol
You can select stream media protocol from the dropdown list.
There are three options: TCP/UDP/Multicast
2.4 System Menu
System menu is shown as in Figure 2-9.
Please refer to chapter 2.2 Live, chapter 3 PTZ, chapter 4 Playback, chapter 5 Setup, chapter 6 Alarm,
chapter 7 Log out for detailed information.
Figure 2-9
2.5 Video Window Function Option
The interface is shown as below. See Figure 2-10
Figure 2-10
Please refer to the following sheet for detailed information.
SN
Parameter
Function
1
Alarm on/off
To control alarm output as:
Red: means alarm output.
Grey: means alarm ends.
Click on this button to control alarm output or turn it off.
1 2 3 4 5 6 7 8 9

8
2
Digital
zoom
When the video is in the original status, click it you can
select any zone to zoom in. In the non-original status,
you can drag the zoom-in zone in specified range. Right
click mouse to restore previous status.
Click it; you can use the middle button of the mouse to
zoom in/out the video size.
3
Snapshot
You can snapshoot important video by clicking on this button.
All images are memorized in system folder: \ picture
download (default).
You can go to Setup->Camera->Video->Path to modify the
local record save path.
4
Triple snap
Click it, system can snap at 1f/s. All images are memorized in
system storage folder.
5
Record
For manual record. All records are memorized in Setup-
>Camera->Video->Path.
6
Easy focus
Click it, you can see there are two parameters on the preview
video：AF Peak and AF Max.
AF Peak: It is to display the video definition during the focus
process.
AF Max: It is the most suitable value for the video definition.
The close the AF Peak and AF Max is, the better the focus
effect is.
7
Audio
output
Turn on or off audio when you are monitoring.
8
Bidirectional
talk
Click it to begin audio talk. You can go to Setup->Camera-
>Audio to set bidirectional talk mode.
9
Help
Click it to open help file.
2.6 Video Window Setup
The interface is shown as in Figure 2-11.
Figure 2-11
2.6.1 Hide Image Control
1 2 3 4 5 6

9
Click this button to display/hide image control interface.
2.6.2 Original size
Click this button to go to original size. It is to display the actual size of the video stream. It depends on
the resolution of the bit stream.
2.6.3 Full screen
Click it to go to full-screen mode. Double click the mouse or click the Esc button to exit the full screen.
2.6.4 Width and height ratio
Click it to restore original ratio or suitable window.
2.6.5 Fluency Adjustment
There are three levels of fluency for you to select. The default is real-time with minimum delay. You may
select fluent mode in case connection is slow.
2.6.6 Zoom and Focus
Click it to open zoom and focus interface. See Figure 2-1312.
Note: It is for motorized zoom lens device only.
Figure 2-12

10
Please refer to the following sheet for detailed information.
Parameter
Function
Zoom
Adjust lens focal length. May adjust via single clicking on or long pressing + - .
Step length is to adjust length of single step.
Focus
Adjust lens definition. May adjust via single clicking on or long pressing + - .
Step length is to adjust length of single step.
Auto focus
Automatically adjust image definition. Click to adjust.
Note:
During auto focus, you cannot perform other lens operation.
Restore
Restore lens to zero to clear accumulated difference.
Note:
Please restore default settings when needed.
Refresh
Sync lens and slide bar location after hardware zooming.
2.6.7 Image control
Click it to open picture setup interface. See Figure 2-13. This interface is on the top right pane.
Figure 2-13
Please refer to the following sheet for detailed information.
Parameter
Function
Video
setup
It is to adjust monitor video
brightness.
Note:
All the operations here apply
to WEB end only.
Please go to Setup-
It is to adjust monitor video
contrastness.

11
It is to adjust monitor video
hue.
>Camera->Conditions to
adjust corresponding items.
It is to adjust monitor video
saturation.
Reset R
e
Restore brightness,
contrastness saturation and
hue to system default setup.

12
3 PTZ Control
Please note only some series product support PTZ function.
Before PTZ operation, please make sure you have properly set PTZ protocol. (Please go to Setup-
>System->PTZ to set.).
Here you can view direction keys, speed, zoom, focus, iris, preset, tour, pan, scan, pattern, aux close,
and PTZ setup button. See Figure 3-1.
PTZ direction: PTZ supports eight directions: left/right/up/down/upper left/upper right/bottom
left/bottom right.
Speed: It controls rotation speed. The step 8 speed is faster than step 1. Default value is 5.
Figure 3-1
PTZ setting interface is shown as in Figure 3-2.
Here you can set scan, preset, tour, pattern, assistant function and light and wiper.

13
Figure 3-2
Please refer to the following sheet for PTZ setup information.
Parameter
Function
Scan
Click Setup button, you can set scan left and right limit.
Move the camera to you desired location and then click left limit
button. Then move the camera again and then click right limit
button to set a right limit.
Preset
Input the preset value and then click Preset button, the camera
turns to the corresponding position of the preset.
Click the Set preset button, you can set a preset. Use direction
keys to move the camera to your desired location and then input
preset value. Click add button, you have set one preset.
The preset value ranges from 1 to 255. (It may vary due to
different protocols.)
Tour
Click the Setup button, you can begin set tour.
Input tour value and then click the Set button. The tour value
ranges from 1 to 255. (It may vary due to different protocols.)
Input preset value in the column. Click Add preset button, you
have added one preset in the tour.
Note:
Repeat the above procedures you can add more presets in one tour.
Or you can click delete preset button to remove one preset from the
tour.
Pattern
You can input pattern value and then click start button to begin PTZ
movement. Please go back to Figure 3-1 to implement camera
operation. Then you can click stop button in Figure 3-2. Now you
have set one pattern.

14
Parameter
Function
Assistant
Please input the corresponding aux value here.
You can select one option and then click AUX on or AUX off button.
Light and
wiper
You can turn on or turn off the light/wiper.

15
4 Playback
4.1 Playback Interface
The playback interface is shown as in Figure 4- 1.
Figure 4- 1
There are four sections:
Section 1: Function of play
Section 2: Date
Section 3: File list
Section 4: Progress bar
4.2 Function of Play
The function of play is shown as in Figure 4- 2.
2
3
4
1

16
Figure 4- 2
1. Play: Play or pause video.
2. Stop: Stop video.
3. Play by frame: Skip to next frame.
4. Slow play: Slow down the video.
5. Quick play: Speed up the video.
6. Silent: Switch off/on sound.
7. Volume: Adjust volume of the video.
Note: You must pause video before skipping to next frame.
4.3 Date
There are various colors in calendar:
Green: means currently selected date.
Yellow: means current date has record file.
Blue: means current date has record file which is/are selected.
Only file types selected will be displayed in progress bar and list.
4.4 File List
The file list is shown as in Figure 4- 3.
1 2 3 4 5 6 7