l-4/B/16CH
Passive
HD
Video
Transceiver
IJll>IJll>
IJll>
----------------
I
Specification
-
Item Description
Channels 4 Channel I 8 Channel I
16
Channel
Function HDCVI 720P:400m /1080P: 250m;
Transmission Distance HDTV! 720P/1080P: 250m;
AHO
720P: 350m/1080P: 200m
Video Connector BNC-F
UTP Cable Connector 8
pin
green
terminal
block,RJ-45
Video Compatible With
HDTVl/HDCVl/AHD
signal
Properties Signal Transmission Band 0-65MHz
Interference Rejection >60db
Video
Connector
Protection
2KV(common
mode)
Per,
IEC61000-4-5
UTP
Cable
Connector 2KV(different
mode)
4KV(common
mode)
Protection
Per:
IEC61000-4-5
,___
Protection
ESD
Contact
Discharge
:
6000V
Air
Discharge
:
8000V
Per
:
IEC61000-4-2
Reliability
MTBF
>20000H
-Size(LWH) 180*85*32mm I 180*100*44mm \430*100*
44
.
5(1
U)
Physical Outer Shell
Iron
Metal
Properties Color Black
-
N.W.
450g I 5809 I 1250g
Operation Temperature o·
c-50°c
Environmental Storage Temperature -2o·
c-ao
·c
Relative Humidity 0%-95%(non-condensing)
Specillcatlons
suject
to
c/Jange wlt/Joutnotice.
•Troubleshooting
If
any
trouble
in
installation,
please
follow
these
steps
:
•
Check
if
it's
according
to
the
manual;
•
If
choose
RJ-45
,
make
sure
both
ends
of
UTP
cable
are
same(both
568A
or
both
5688)
•
If
choose
green
terminal
block
,
make
sure
cable
of
same
color
be
in
the
same
pin
;
•
Check
all
connection(like
BNC
,
RJ-45)
;
•
Make
sure
the
real
distance
not
exceeds
the
allowed
transmission
distance
;
•
Make
sure
the
cables
are
quality
;
•
Replace
the
device
at
question
by
a
normal
working
device
;
•
Please
contact
your
vendor
if
trouble
still
exists
.
•How
to
make
RJ
45
Plug
Instruments to
be
used: wire crimper, network tester.
Wire sequence
of
RJ45 plug should conform with EIAfTIA568A
or
5688
.
1.
Shuck off about 2cm long the insulating layer, and bar the 4 pairs UTP cable.
2.
Depart the 4 pairs UTP cable and straighten them.
3.
Line up the 8 pieces
of
cables per EIAfTIA 568A
or
5688
.
4. Brunt cut the cables to leave 1.5cm bare wire.
5.
Plug 8 cables into RJ45 plug, make sure each cable is in each pin.
6. Then use wire crimper to crimp it.
7. Repeat above 5 steps to make the another end.
8. Using network tester to test the cable whether is working.
•
RJ
45
PIN
Diagram
Pin
Diagram
1 (1)
video+
2 (1)
video
-
3
(2)
video+
4
(3)
video+
5 (
3)
vi
deo
-
s
(2)
video-
7
(4)
video+
8
(4)
video·
EIA/TIA
568A
LL
Attention:
1 (1)
video+
2 (1)
video·
3 (2)
video+
4 (3)
video+
5 (3)
video
-
s (2)
video
-
7 (4)
video+
8
(4)video-
EIA/TIA
5686
•If
choose
green
terminal
block
,
cable
of
same
color
should
be in
the
same
pin.
•When
choose
RJ-45,make
sure
if
one
end
is
EIA/TIA568A,the
other
end
should
also
be
EIA/TIA568A.
•or
if
one
end
is
EIA/TIA568B,the
other
end
should
also
be
EIA/TIA568B.
•Package
Contents
• 4/8/16CH passive
HD
video transceiver
• Application manual
• Rack-mounting ear
• Rack-mounting screws
• Robber pad
(1
pc)
(1
pc)
(2
pcs)
(8
pcs)
(4
pcs)
