Security-Center FU5125 User manual

Installa
t
ion Guide
FU5125
Radio-controlled
vibration detector

Fig. 1
Fig. 2

Preface
Dear Customer,
Thank you for purchasing this radio-controlled vibration detector. You
made the right decision in choosing this state-of-the-art technology,
which complies with the current standards of domestic and European
regulations. The CE has been proven and all related certifications are
available from the manufacturer upon request.
To maintain this status and to guarantee safe operation, it is your
obligation to observe these operating instructions! In the event of
questions, please contact your local specialist dealer.
This radio-controlled vibration detector monitors vibrations. You can use it
to monitor movable objects such as windows and doors. If a vibration
above a predefined level is detected, it is signalled to a radio alarm
station.
Read carefully the notes and advice in these operating
instructions! If you do not follow these instructions, your
guarantee claim becomes invalid! We can accept no liability for
the consequences!
No part of the product may be changed or modified in any way.
!

Fig. 1
Number Name
1 LED
2 Screw
3 Battery
4 Potentiometer
5 Tamper protection, lid
6 LED – calibration mode
7 Tamper protection, wall
8 Jumper contacts A–D
Do NOT install the detector:
•Near the floor
•Near large metal structures
•Within 1 metre from power or gas lines
•Near electronic or radio equipment
•On moveable elements
•Upside down
Installation
1. Open the casing by loosening the screw and then removing the cover.
2. Remove the PCB from the housing: Pull the PCB carefully away from
the plastic clamps.

3. Fig. 1, Pos. 1: Positions of screws for fixing the housing
3.1. Hold the bottom of the housing at a suitable position.
3.2. Mark the screw positions for fixing.
4. Fix the housing rear to the marked position with two screws.
The rear of the housing must lie flat on the surface so that the wall
removal contact is closed.
5. Insert a battery. Check for correct polarity.
6. Replace the PCB in the housing.
Learning
1. Switch your radio alarm equipment / radio receiver to learn mode.
See the system instructions for advice on this.
2. Radio variant:
Hold the tamper protection for the front panel / and the wall removal
contact down with the finger and release it several time to trigger
radio signals.
IR variant:
Point the LED of the radio-controlled vibration detector at the IR
receiver of the radio extension (RFX). Now trigger the tamper contact
of the detector.
3. Make sure that the vibration detector is recognised by your radio
alarm equipment / radio receiver.

Setting the vibration detector
There are various options for setting the vibration detector.
Jumper A Sensitivity:
The detector can be set to high or low sensitivity with
jumper A.
low
high
You can set the sensitivity range with the potentiometer
(Fig.1, 4).
Jumper B XXX: Multiple vibration mode
If XXX is activated, the vibration detector sends an
alarm after repeated vibrations.
Off
On
Jumper C Calibration:
Use this jumper to set the detector to calibration mode
or normal operation.
Calibrate detector
Normal
Jumper D LED:
Use this jumper to activate/deactivate the LED of the
detector.
Off
On

Adjusting sensitivity
Connect jumper C. Note: If the detector battery is almost empty, the LED
flashes continuously for calibration mode (Fig.1, 6). In this case, replace
the battery.
1. Turn the potentiometer (Fig.1, 4) anticlockwise until it stops. The
detector is now at the lowest sensitivity level.
2. Tap the sensor with your hand. Tap it hard enough to trigger an
alarm.
The calibration mode LED (Fig.1, 6) flashes
1x for a small vibration,
2x for a vibration that triggers an alarm and
3x for a strong vibration.
3. Adjust the potentiometer until the LED (Fig.1, 6) flashes 2x at every
vibration in the sensitivity range.
4. Remove jumper A if the sensor does not register all vibrations in the
desired sensitivity range.
5. Remove jumper C when you have set the sensor to the desired
sensitivity. This puts the sensor into normal operating mode.

Changing the battery
1. Switch your radio alarm equipment to installer mode.
2. Open the housing of the vibration detector.
3. Replace the battery with one of the same type
(CR 2 Lithium, 3V).
Closing the case
Place the cover on the base and fix it with the screw.
Technical Data
Power supply: 3V, CR2 Li/MnO2
Battery life: 3 – 5 years
Temperature Range: -10°C to +55°C
Dimensions: 118 x 30 x 27 mm (HxWxD)
Security grade: 2
Environmental class: 2
Incert No.: XXXXXX