Securitytronix HD-COAXINATORTVI ST-HDC2PTZ User manual

ST-HDC2PTZ
QUICK START GUIDE
www.ŶĂĐĞďƌĂŶĚƐ.com www.securitytronix.com

ST-HDC2PTZ·Quick Start Guide
ii
Quick Start Guide
About this Manual
This Manual is applicable to HD-COAXINATORTVI Speed Dome Cameras.
This Manual includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in this Manual is subject to change, without notice, due to firmware updates or other
reasons. Please use this user manual under the guidance of professionals.
03261060707

ST-HDC2PTZ·Quick Start Guide
iii
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

ST-HDC2PTZ·Quick Start Guide
iv
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid
danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
All electronic operation should be in strict compliance with the electrical safety regulations, fire
prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided with the camera. The standard of the power
adapter is 24VAC10% or 12VDC10% (depending on models). The power consumption cannot
be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle the
speed dome.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and contact support for further assistance.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility
for problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetic radiation. Avoid installing the equipment on surfaces subject to shock or
vibration (failure to do so can cause equipment damage).
Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire or
electrical shock may occur. The operating temperature should be -22°F ~ 149°F(outdoor speed
dome) and -14°F ~ 122°F (indoor speed dome).
The indoor dome cover should be protected from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or a heat source such as heater or
radiator should be avoided (failure to do so could cause a fire hazzard).
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

ST-HDC2PTZ·Quick Start Guide
v
Do not aim the speed dome at the sun or extremely bright scenes. A blooming or smear may
occur (which is not a malfunction), and affecting the longevity of sensor at the same time.
Please use the provided glove when opening up the dome cover, avoid direct contact with the
dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome
cover.
Please use a soft and dry cloth when cleaning inside and outside surfaces of the dome cover, do
not use alkaline detergents.
Please keep all wrappers after unpacking them for future use. In case of any failure, you will need
to return the speed dome to the factory with original packaging to prevent to damage to the
camera while in transit.
For further assistance, or if you encounter any issue while using this product, please contact your
distributor or Securitytronix at: 800-688-9282 Press 3 for support, then 2 for CCTV.

ST-HDC2PTZ·Quick Start Guide
vi
Table of Contents
1 Installation ........................................................................................................ 1
1.1 Connecting the Cables.............................................................................................................. 1
1.2 DIP Switch Settings ................................................................................................................... 2
1.2.1 5-inch Speed Dome Settings.............................................................................................. 2
1.2.2 5-inch IR & Mini IR Speed Dome Settings .......................................................................... 4
1.2.3 7-inch IR Speed Dome Settings.......................................................................................... 7
1.2.4 Mini Speed Dome Settings ................................................................................................ 9
1.3 Wiring and Installation ........................................................................................................... 11
1.3.1 Wiring.............................................................................................................................. 11
1.3.2 Installing the Bracket ....................................................................................................... 12
1.3.3 Setting the DIP Switch ..................................................................................................... 13
1.3.4 Installing the Speed Dome............................................................................................... 13
2 In-door Mounting Applications....................................................................... 14
2.1 5-inch Speed Dome In-ceiling Mounting Applications ............................................................ 14
2.2 5-inch Speed Dome Ceiling Mounting Applications................................................................ 16
2.2.1 Removing the Mounting Bracket ..................................................................................... 16
2.2.2 Wiring.............................................................................................................................. 17
2.2.3 Ceiling Mounting ............................................................................................................. 18
2.3 Mini Speed Dome In-ceiling Mounting Applications............................................................... 20
2.4 Mini Speed Dome Ceiling Mounting Applications .................................................................. 22
2.4.1 Wiring.............................................................................................................................. 22
2.4.2 Ceiling Mounting ............................................................................................................. 22
3 Application and Operations ............................................................................ 24
3.1 System Application ................................................................................................................. 24
3.2 Basic Operations..................................................................................................................... 24
3.2.1 Configuring Patrol............................................................................................................ 25
3.2.2 Configuring Park Actions ................................................................................................. 28
4 Troubleshooting.............................................................................................. 30
4.1 Device Exceptions................................................................................................................... 30
4.2 PTZ Control Exceptions........................................................................................................... 30
4.3 Other Questions ..................................................................................................................... 30

ST-HDC2PTZ·Quick Start Guide
1
1Installation
Before you start:
Check the package contents and make sure that the device in the package is in good condition and
all the assembly parts are included.
There are several ways to install the HDC-TVI speed dome. The wall mounting is taken as an
example below.
1.1 Connecting the Cables
Please turn the power off before connecting the cables.
The cable interfaces of speed dome are shown in following figure. The cables are distinguished by
different colors. The labels attached on the cables are for identification.
The cables may vary according to different camera models. Please refer to the actual device.
REDAC24V
YELLOW/GREEN
BLACKAC24V
YELLOWR485-
ORANGER485+
VI EOD
Alarm
HD-TVI Video Output
Power Supply
VI E OD
CVBS Video Output
RS485
Figure 1-1 Cables
Table 1-1 Cables Description
Name
Description
Power Supply
24V AC/ 12V DC
HDC-TVI Video Output
HDC-TVI and coaxial video output
CVBS Video Output
SD analog video output
RS485
RS 485 control
Alarm
Alarm input and alarm output

ST-HDC2PTZ·Quick Start Guide
2
1.2 DIP Switch Settings
1.2.1 5-inch Speed Dome Settings
The DIP switch is used for setting the address and baudrate for the speed dome, with value ON=1
and OFF=0.
The SW1 switches from the first to the eighth are used to set the address. The SW2 switches are
used to set the baudrate.
The default dome address is 0. The default baudrate is 2400.
123456781
2
DIP Switch
Figure 1-2 DIP Switch Settings for 5-inch Outdoor Speed Dome
1 2 3 4 5 6 7
8
1 2
DIP Switch
Figure 1-3 DIP Switch Settings for 5-inch Indoor Speed Dome
Figure 1-4 Enlarged View of DIP Switch
Address Settings
The SW1 switches from 1 to 5 are used for setting the address of speed dome. You can refer to
Table 1-2 for details of setting the speed dome address to a specific number.

ST-HDC2PTZ·Quick Start Guide
3
Table 1-2 Set the Dome Address
Switch No.
Dome Address
1
2
3
4
5
0
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
…
…
…
…
…
…
31
ON
ON
ON
ON
ON
Protocol Settings
The number 6 and 7 of SW1 switches are for setting the protocol of the speed dome. You can refer
to Table 1-3 for details of setting the speed dome protocol.
Table 1-3 Set the Protocol of the Dome
Switch No.
Protocol
6
7
Self-adaptive
OFF
OFF
PELCO_D
ON
OFF
MAN_BOSCH
OFF
ON
MAN_AD
ON
ON
TVI Mode Settings
The number 8 of SW1 switches is for setting the TVI mode of the speed dome. You can refer to
Table 1-4 for details of TVI mode settings.
Table 1-4 Set the TVI Mode
Switch No.
TVI Mode
8
V2.0
OFF
V1.0
ON
Baudrate Settings
The number 1 and 2 SW2 switches are used for setting the baudrate of the speed dome. The
baudrate can be 2400bps, 4800bps, 9600bps and 19200bps. The baudrate will be set as 2400bps by
default if it is out of this range. Refer to the following table:

ST-HDC2PTZ·Quick Start Guide
4
Table 1-5 Set the Baudrate of the Dome
Switch No.
Baudrate
1
2
2400
OFF
OFF
4800
ON
OFF
9600
OFF
ON
19200
ON
ON
1.2.2 5-inch IR & Mini IR Speed Dome Settings
The DIP switch is for setting the speed dome address, baudrate, protocol, etc., with value ON=1 and
OFF=0. The switch label of the 5-inch IR speed dome is on the back of the SWITCH cover as shown
in Figure 1-5. The DIP switch of mini IR speed dome is shown in Figure 1-6.
DIP Switch
Screws
Switch Cover
Figure 1-5 Position of DIP Switch for 5-inch IR Speed Dome
DIP Switch Location of Mini IR Speed Dome
Screws DIP Switch
Figure 1-6 DIP Switch of Mini IR Speed Dome
Setting DIP Switch

ST-HDC2PTZ·Quick Start Guide
5
1 75 6432 8 9 10
ON DIP
1 2
ON
Figure 1-7 Enlarged View of DIP Switch
For some certain models, the two individual DIP switches at the left side of the Figure 1-7 are
supported for turning on/off the terminator; while other models are not supported.
The default dome address is 0; the default baudrate is 2400; and the default value of the 120Ω
terminator is OFF.
Table 1-6 Switch Functions
Switch
Function
1 to 5
Set the address for the speed dome
6, 7
Set the baudrate for the speed dome
8
Set the protocol for the speed dome
9
Set the TVI mode for the speed dome
10
Set the terminal resistor for the speed dome
The DIP switch is designed according to binary system. When the switch is ON, it stands for the
number 1. When the switch is OFF, it stands for the number 0.
Example:
The switches from No. 1 to 5 are used to set the speed dome address. No. 1 is the lowest digit and
No. 5 is the highest. Turning on all these 5 switches stands for the binary number 11111. Converting
the 11111 to a decimal number is 31. So the speed dome address will be 31.
Address List
For convenient settings, refer to the following list to set the address for the speed domes.
Table 1-7 Dome Address
Switch No.
Dome Address
1
2
3
4
5
0
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
…
…
…
…
…
…
31
ON
ON
ON
ON
ON

ST-HDC2PTZ·Quick Start Guide
6
Baudrate List
For convenient settings, refer to the following list to set the baudrate for the speed dome. The
baudrate will be set as 2400bps by default.
Table 1-8 Baudrate
Switch
Baudrate
6
7
2400
OFF
OFF
4800
ON
OFF
9600
OFF
ON
19200
ON
ON
Protocol List
For convenient settings, refer to the following list to set the protocol for the speed dome.
Table 1-9 Protocol
Protocol
8
Self-adaptive
OFF
MAN_AD
ON
TVI Mode
Table 1-10 TVI Mode
TVI Mode
9
V2.0
OFF
V1.0
ON
The speed dome is self-adaptive to private protocol when the No.8 and 9 switches are both
OFF.
Terminal Resistor
Table 1-11 Terminal Resistor
Terminal Matching Resistance
10
Turn on the Resistor
ON
Turn off the Resistor
OFF

ST-HDC2PTZ·Quick Start Guide
7
1.2.3 7-inch IR Speed Dome Settings
Two DIP switches SW1 and SW2 are for setting the speed dome address, baudrate, protocol, etc.,
with value ON=1 and OFF=0. The switch label is on the back of the SWITCH cover as shown in Figure
1-8.
Each number of the switch represents a DIP value, ranging from 1 to 8 for the lowest to highest.
SW1 SW2
Figure 1-8 Label of DIP Switch for IR Speed Dome
ON
12345678
SW2
ON
12345678
SW1
Figure 1-9 Enlarged View of DIP Switch
The default dome address is 0; the default baudrate is 2400; and the default value of the 120Ω
terminator is OFF.
Address Settings
The SW1 switches are used for setting the address of speed dome. You can refer to Table 1-12 for
details of setting the speed dome address to a specific number.
Table 1-12 Set the Dome Address
Dome Address
1
2
3
4
5
6
7
8
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
...
...
...
...
...
...
...
...
...
255
ON
ON
ON
ON
ON
ON
ON
ON

ST-HDC2PTZ·Quick Start Guide
8
Baudrate Settings
The No. 1, 2 of SW2 switches are for setting the baudrate of the speed dome, standing for 2400bps,
4800bps, 9600bps and 19200bps respectively. The baudrate will be set to 2400bps by default if it is
out of this range, refer to the following table:
Table 1-13 Set the Baudrate of the Dome
DIP Switch SW2-Baudrate Settings
Baudrate
1
2
2400
ON
OFF
4800
OFF
ON
9600
ON
ON
19200
OFF
OFF
Protocol Settings
For convenient settings, refer to the following list to set the protocol for the speed dome.
Table 1-14 Set the Protocol of the Dome
DIP Switch SW2-Protocol Settings
Protocol
3
4
5
Self-adaptive
OFF
OFF
OFF
PELCO_P
ON
OFF
OFF
PELCO_D
OFF
ON
OFF
HIKVISION
ON
ON
OFF
KALATE
OFF
OFF
ON
VICON
ON
OFF
ON
MAN_BOSCH
OFF
ON
ON
MAN_AD
ON
ON
ON
TVI Mode Settings
The No. 7 of SW2 switches is for setting the TVI mode of the speed dome. You can refer to the
following table for details of setting the speed dome TVI mode.
Table 1-15 Set the TVI Mode
TVI Mode
7
V2.0
OFF
V1.0
ON

ST-HDC2PTZ·Quick Start Guide
9
Terminal Resistor Settings
The No. 8 of SW2 switches is used for turning on/off the 120Ωterminal resistor.
Table 1-16 Set Terminal Resistor
Terminal Matching Resistance
8
Turn on the Resistor
ON
Turn off the Resistor
OFF
The o-ring in the groove of the switch cover is for waterproof.
1.2.4 Mini Speed Dome Settings
DIP Switch Location of Mini HDC-TVI Speed Dome
DIP Switch
Figure 1-10 DIP Switch of Mini HDC-TVI Speed Dome
Setting DIP Switch
1 75 6432 8 9 10
ON DIP
1 2
ON
Figure 1-11 Enlarged View of DIP Switch
Table 1-17 Switch Functions
Switch No.
Function
1 to 5 (SW1)
Set the address for the speed dome
6, 7 (SW1)
Set the baudrate for the speed dome
8, 9 (SW1)
Set the protocol for the speed dome
10 (SW1)
Set the TVI mode for the speed dome
1,2 (SW2)
Set the terminal resistor for the speed dome

ST-HDC2PTZ·Quick Start Guide
10
The DIP switch is designed according to binary system. When the switch is ON, it stands for the
number 1. When the switch is OFF, it stands for the number 0.
Example:
The SW1 switches from No. 1 to 5 are used to set the speed dome address. No. 1 is the lowest digit
and No. 5 is the highest. Turning on all these 5 switches stands for the binary number 11111.
Converting the 11111 to a decimal number is 31. So the speed dome address will be 31.
Address List
For convenient settings, refer to the following list to set the address for the speed domes.
Table 1-18 Dome Address
Switch No.
Dome Address
1
2
3
4
5
0
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
…
…
…
…
…
…
31
ON
ON
ON
ON
ON
Baudrate List
For convenient settings, refer to the following list to set the baudrate for the speed dome. The
baudrate will be set as 2400bps by default if it is out of this range.
Table 1-19 Baudrate
Switch No.
Baudrate
6
7
2400
OFF
OFF
4800
ON
OFF
9600
OFF
ON
19200
ON
ON
Protocol List
For convenient settings, refer to the following list to set the protocol for the speed dome.

ST-HDC2PTZ·Quick Start Guide
11
Table 1-20 Protocol
Switch No.
Protocol
8
9
Self-adaptive
OFF
OFF
Pelco_P
ON
OFF
The speed dome is self-adaptive to private protocol when the No.8 and 9 switches are both
OFF.
TVI Mode
For convenient settings, refer to the following list to set the TVI mode of the speed dome.
Table 1-21 TVI Mode
Switch No.
TVI Mode
10
V2.0
OFF
V1.0
ON
Terminal Resistor
Table 1-22 Terminal Resistor
Switch No.
1
2
Turn on the Resistor
ON
ON
Turn off the Resistor
OFF
OFF
1.3 Wiring and Installation
There are several ways to install the speed dome. The wall mounting is taken as an example below.
1.3.1 Wiring
Surveying of the installation environment and wire planning is highly recommended before actual
deployment of the wire is implemented in order to provide a safe and steady power supply and a
reasonable wiring route.
Get familiar with the installation environment before deploying the wire, including the wiring
distance, surrounding, and electromagnetic interference and so on.
Please choose the cable with nominal voltage higher than the actual voltage, to ensure normal
operation.
To protect the power cable and the signal transmitting cable from human tampering, you

ST-HDC2PTZ·Quick Start Guide
12
should pay attention to the routing and reinforcement of the cables.
When deploying the wire, please do not over tighten the wires or leave the wire loose.
*The wiring of the speed dome camera should be performed by professionals.
1.3.2 Installing the Bracket
Before you start:
Wall mounting is applicable for indoor/outdoor solid wall construction. The following are the
mandatory conditions for wall mounting:
The wall must be thick enough to install the expansion screws.
Please make sure that the wall is strong enough to withstand more than 8 times the weight of
the dome and the mount.
Steps:
1. Check whether the type of the bracket and the number of accessories are right, as shown in
the figure below.
Figure 1-12 Wall Mount Bracket, Nuts and Flat Washers
2. Drill 4 screw holes in the wall according to the holes of the mount, and then insert M8
expansion screws (not supplied) into the mounting holes.
Figure 1-13 Drill Mounting Holes
3. Attach the wall mount to the wall by aligning the 4 screw holes of the mount with expansion
screws on the wall.
4. Secure the wall mount with 4 hex nuts and washers.
Figure 1-14 Secure the Mount

ST-HDC2PTZ·Quick Start Guide
13
5. Install the speed dome to the mount. Please refer to Section 1.3.4 Installing the Speed Dome
for installation details.
Follow the same instructions described above for the short-arm wall mounting. For outdoor
applications, please ensure water proofing measures are taken. The short-arm wall mount is
not optimal for outdoor applications.
1.3.3 Setting the DIP Switch
Set the address and baudrate for the speed dome. The default value of DIP switch is shown below:
Address: 0
Baudrate:2400
Terminal Resistor: OFF
Please refer to the Section 1.2 DIP Switch Settings for DIP switch settings.
1.3.4 Installing the Speed Dome
The sketches of installing the speed dome are for reference only.
Steps:
1. Hang the safety rope to the speed dome and then hook to the mount as shown in Figure
1-15(left).
2. Route the cables of the speed dome through the wall mount.
3. Connect the corresponding video/power/RS-485 cables.
4. Install the speed dome to the mount, and secure the speed dome by rotating the speed dome
clockwise.
5. Fasten the two lock screws with the Allen wrench, as shown in Figure 1-15(right).
③
②
①
Figure 1-15 Install the Speed Dome

ST-HDC2PTZ·Quick Start Guide
14
2In-door Mounting Applications
Before you start:
For cement wall, you need to use expansion screws to fix the mount. The mounting hole of the
expansion pipe on the wall should align with the mounting hole on the mount.
For wooden wall, you can just use the self-tapping screw to fix the mount.
2.1 5-inch Speed Dome In-ceiling Mounting
Applications
Before you start:
The in-ceiling mounting is applicable for ceiling construction. The following are mandatory
conditions for mounting:
The height of the space above the ceiling must be more than 250mm.
The thickness of the ceiling must range between 5 and 40mm.
The ceiling must be strong enough to withstand more than 4 times the weight of the dome and
its accessories.
Steps:
1. Rotate the lower dome counterclockwise to separate it from the back box as shown in Figure 2-1.
2. Remove the protective lens cover, foam and sticker from the dome drive.
3. Set the address and baudrate for the HDC-TVI speed dome. Please refer to the Section 1.2.1
5-inch Speed Dome Settings for DIP switch settings.
4. Attach lower dome to the back box, and rotate clockwise to secure it.
Protective Foam
Sticker
Lower Dome
Back Box
Figure 2-1 Remove the Protective Accessory
5. Drill a hole on the ceiling according to the drill template (supplied).
±2mm of the diameter of the circle is tolerable.