Securitytronix ST-IP-MD36-1 User manual

ST-IP-MD36-1
ST-IP-MD36-2
HD Mini Network Dome Camera Quick Start Guide
Version 1.0.0

2
Welcome
Thank you for purchasing our Networkcamera.
This Quick Start Guide is designed to get yoursystem up and running as easily as possible.
This document applies to both the ST-IP-MD36-1 and ST-IP-MD36-2 camera models (1mp &
2mp).
Please read the following safeguard and warnings carefully before you use this camera.
Please keep this document for futurereference.
Important Safeguards and Warnings
1．Electrical safety
All installation and operation should conform to your local electrical safetycodes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power supply
requirement is subject to the devicelabel).
Please prevent the line cord from being crushed or damaged, especially at the plug, power
socket and the junction from the device.
Note: Do not connect a PoE power source AND a power supply to the device at the same
time; it may result in device damage.
We assume no liability or responsibility for fires or electrical shock caused byimproper
handling or installation.
We are not liable for any problems caused by unauthorized modification or attemptedrepair.
2．Environment
Don’t aim the device at strong light (such as lighting, sunlight and so on) to focus;
otherwise it may cause overexposure, which will affect the longevity of the CCD or CMOS
imager.
Please transport, use and store the device within the range of allowed humidity and temperature.
Don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and with
strong electromagnetic radiation or unstablelighting.
Please do not allow water and other liquids to enter the camera, to prevent the internal
components from being damaged.
Please allow adequate ventilation around the camera to prevent heataccumulation.
Please pack the device with the standard factory packaging or material with the same
quality when transporting the device.
Avoid bumps and humidity during transportation, storage and installation.

3
3. Operation and Daily Maintenance
Please do not dismantle the device; Doing so may void your warranty.
It is recommended to use this camera with a surge-protection device.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use an air blower to clean
the dust or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the
dust gently if it is necessary to clean.
Always use a dry, soft cloth to clean the device. If there is too much dust, please use the water to
dilute mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device. Don’t use volatile solvents like alcohol, benzene, thinner etc or strong detergents with
abrasiveness, otherwise it will damage the surface coating or reduce the working performance of
the device.
The dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods to clean a dirty lens:
Stained with dirt:
Use an oil-free soft brush to gently remove it.
Stained with grease or fingerprints:
Use a soft cloth to wipe the dome gently to dry it, then use oil-free cotton cloth or paper soaked
with alcohol or detergent to wipe from the lens center to outward. It is ok to change the cloth and
wipe several times to get all of the dirt off.
Warning
Please use the standard accessories provided by SecurityTronix and make sure the device is
installed and repaired by professional engineers.
Please do not provide two or more power supply modes for the device, otherwise it may cause
damage to the device.
Statement
Please refer to the actual product for more details; this manual is just forreference.
Please contact the supplier or customer service if there is any problem occurred when using the
device.
Please contact the customer service for the latest procedure and supplementary documentation.
There may be deviation between the actual value of some data and the value provided in the
manual due to the reasons such as the real environment is not stable and so on. Please refer to
the company’s final explanation if there is any doubt ordispute.

4
The company is not liable for any loss caused by operation which is inconsistent with the
instructions in the manual.
Note:
Please refer to the disk for more details. Check and download corresponding user’s manuals
and tools from the SecurityTronix website: http://www.securitytronix.com/support/
Before installation, please open the package and ensure all the components areincluded.
Contact your local retailer ASAP if something is broken in yourpackage.
Accessory Name Amount
Network Camera Unit 1
Installation Accessories bag
1
Quick Start Guide 1
CD 1

5
Table of Contents
1 Framework.........................................................................................................................5
1.1 Structure..............................................................................................................5
1.2 Dimensions..........................................................................................................6
2 Installation.........................................................................................................................8
2.1 Device Installation..............................................................................................8
2.2 Micro SD Card Installation................................................................................9
3 Network Configuration...................................................................................................11
3.1 Modify IP Address............................................................................................11
3.2 Login WEB Interface........................................................................................12

6
1 Physical Properties
1.1 Structure
Note:
The following diagram is for reference only, to illustrate the device component and cable port
functions.
Device component and cable port function may differ according to different models, please refer
to the actual device for details.
Figure 1-1
Please refer to the following sheet for detailed structureinformation.
Component
Component name
1 X-Y-Z rotation module
2 Device lens
3 Dome camera enclosure
Please refer to the following sheet for detailed portinformation.
Port Port name Function
4
Power input port Connect to a 12VDC power supply

7
5
Network port
Network data input, output and
PoE.
Note:
Some devices do not support
PoE.
6 MIC hole Audio input
1.2 Dimensions
Please refer to the following figure for the dimension information. Dimensions are listed in
millimeters. See Figure 1-1 through Figure 1-3.
Figure 1-1 Dimension illustration1
Figure 1-2 Dimension illustration2

8
Figure 1-3 Dimension illustration 3

9
2 Installation
2.1 Device Installation
Figure 2-1 Device installation illustration 1
Important
Please make sure the installation surface can support at least 3 times the weight of the
camera and the bracket.
Please refer to the steps listed below.
Step1
Use the inner hexagonal wrench (provided) to loosen the three inner hexagon screws in the
outer dome cover and then remove the cover.
Step 2
Locate the installation template in the accessories bag, and affix it to the ceiling or wall
according to your monitor arearequirements.
Step 3
Drill 3 holes, 3/16” diameter as indicated at the marks on the template. Remove the template
and insert the 3 included plastic expansion anchors in the holes.
Note:
If the cable must exit behind the installationsurface (behind a wall or inside the ceiling),
Drill a ¾” cable exit hole in the mounting surface according to the installation template.
If the cable must exit the camera on the surface of the wall or ceiling, use a strong needle-
nose plier or similar tool to pry out and remove the thin metal of the camera’s outer shell, as
shown in Figure 2-1 above; “Remove this for surface-cable use”.
Remove this for surface-cable use

1
Step 4
Adjust the base of the camera to the proper position and then pull the cable through the cable
exit hole drilled earlier in the ceiling or wall. Line up the TOP direction of the device to the
installation template and then line up the three screw holes in the camera’s base to the three
plastic anchors in the mounting surface. Install the three self-tapping screws firmly into the
anchors.
Step 5
Use the ‘inner hexagonal wrench’ to loosen the two screws which secure the lens rotation
structure NOTE: Do not remove these screws. Only loosen them enough for the camera
housing to move freely to the correct viewing position. Adjust the lens to the required
viewing angle, then secure the screws of the lens rotation structure. The lens adjust angle
ranges are: flip (0°~+75°), video pan rotation (-15°~+15°), video rotation angle(-15°~+15°).
Figure 2-2 Device installation illustration 2
Step 6
Line up the dome camera cover to the cable exits and reinstall the cover. Use the inner
hexagonal wrench to secure the three inner hexagonal screws firmly.
Note:
If you want to restore the factory default settings of the camera, remove the outer cover and
press and hold the Reset button in Figure 2-2 with power on for10s.
2.2 Micro SD Card Installation
Note:
This model of camera does not support Micro SD card functions.
Step 1
Open the camera by referring to step 1 in chapter 2.1 deviceinstallation.
Step 2
Find the “Micro SD CARD” mark on the inner cover, adjust the direction of Micro SD cardand
complete installation according to the location shown in the Figure3-3.

10
Step 3
Please complete the operation by referring to step 6 in chapter 2.1 deviceinstallation.
Figure 2-3

11
3 Network Configuration
The IP address of each camera is the same when leaving the SecurityTronix factory (default
IP192.168.1.108). For the smoothest project installation, please allocate a useable IP segment
of the entire network according to the actual networkenvironment.
3.1 Modify IP Address
IP address can be acquired and modified through the quick configuration tool for the cameras
which is accessed via a wired network; Cameras must connect via a wired network to configure
wireless parameters before using wireless network cameras. This chapter will introduce the
approach of modifying IP addresses via the “Quick Configuration Tool”. You can also modify the
IP address in the network parameters of the WEB interface. Please refer to the document in the
disk << WEB Operation Manual>> for more details.
NOTE:
Currently the quick configuration tool only supports cameras which are addressed within the
same network segment (subnet) as the computer’s IP address.
Step 1 Double click the “ConfigTools.exe” and open the quick configuration tool.
Step 2 Double click the device to be configured, and the “Login” dialog box will appear. Enter the
IP address, user name, password and port number of the camera, and click “Confirm”.
Note:
The default user name and password are admin and admin respectively. The default portnumber
is 37777. See Figure 3-1 for more details.

12
Figure 3-1
Step 3 Modify the camera IP address on the “Net” interface, click “Save” to finishmodification.
See Figure 3-2 for more details.
Figure 3-2
3.2 Login WEB Interface
Note:
Different devices may have different WEB interfaces, the figures below are just for reference,
please refer to the document <<WEB Operation Manual>> in the disk and the actual interface for
more details
Step 1 Open IE and input the modified camera IP address in the addressbar.
Step 2 The login interface is shown below, please input your user name and password (Default
user name is admin and password is admin respectively), click“login”.
See Figure 3-3 for more details.

13
Figure 3-3
Step 3 Install controls according to the system prompt; see Figure 3-4 for the WEB main
interface. Please modify the administrator password as soon as possible after you successfully
logged in.
Figure 3-4

14
Note
•This quick start guide is for reference only. Slight difference may be found in the
user interface.
•All the designs and software here are subject to change without prior written
notice.
•Please visit our website or contact your local service engineer for more
information.
SecurityTronix offers live, human tech support for our products 24 hours a day, 7 days a week,
365 day a year.
Technical support contact info:
Phone: [phone] Option #3, then #2
Email: [e-mail]
Web: www.securitytronix.com/support
SecurityTronix
1085 Andrew Dr. Ste A
West Chester, PA 19380