Securitytronix ST-PTZ650FM-23X User manual

ST-PTZ650FM-23X
INDOOR FLUSH MOUNT PTZ CAMERA
Installation Manual

WARNINGS AND CAUTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS
THROUGH VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT.
PRECAUTIONS:
1. Persons without technical qualifications should not attempt to operate this dome device before
reading this manual thoroughly.
2. Remove any power to the dome before attempting any operations or adjustments inside the
dome cover to avoid potential damage to the mechanism.
3. Inside the dome cover there are precision optical and electrical devices. Heavy pressure,
shock and other sudden adjustments or operations should be avoided. Otherwise, you may
cause irreparable damage to the product.
4. Please DO NOT remove or disassemble any internal parts of the video camera to avoid
normal operation and possibly void the warranty. There are no serviceable parts inside the
camera.
5. All electrical connections to the dome should be made in strict accordance with the attached
labels and wiring instructions in this manual. Failure to do so may damage the dome beyond
repair and void the warranty.
6. For outdoor installation especially in high places or poles, it is highly recommended that the
proper lightning arrestors and surge suppressors are installed before the dome is entered into
service.
7. Please do not use the product under circumstances where the limits exceed the maximum
specified temperature, humidity or power supply specifications.

1
IMPORTANT SAFEGUARDS
1. Read these instructions before attempting installation or operation of this camera
2. Keep these instructions for future reference
3. Heed all warnings and adhere to electrical specifications Follow all instructions
4. Clean only with non abrasive dry cotton cloth, lint free and approved acrylic cleaners
5. Should the lens of the camera become dirty, use special lens cleaning cloth and solution to
properly clean it.
6. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions
7. Use only attachments or accessories specified by the manufacturer
8. Verify that the surface you are planning to use for attaching the dome can adequately support
the weight of the device and mounting hardware
9. Protect this device against lighting storms with proper grounding, power supplies, surge
suppressors and wiring.
10. Refer all servicing to qualified service personnel. Servicing is required when the device has
been damaged in any way, when liquid traces are present, or the presence of loose objects is
evident or if the device does not function properly, or has received sever impact or has been
dropped accidentally.
11. Indoor dome is for indoor use only and not suitable for outdoor or high humidity locations.
Do not use this product under circumstances exceeding specified temperature and humidity
ratings.
12. Avoid pointing the camera directly to the sun or other extremely bright objects for prolonged
period of time avoiding the risk of permanent damages to the imaging sensor.
13. The attached instructions are for use by qualified personnel only. To reduce the risks of
electric shock do not perform any servicing other than contained in the operating instructions
unless you are qualified to do so.
14. During usage, user should abide by all electrical safety standards and adhere to electrical
specifications for the operation of the dome. The control cable for RS485 communications as
well as the video signal cables should be isolated from high voltage equipment and or high
voltage cables.
15. Use supplied power supply transformer only.
1 Product Introduction
Package Contents
High Speed dome 1pc
Power supply 1pc
User manual 1pc

2
Specification
Horizontal Rotation Speed
200°/s
Tilt Rotation Speed
100°/s
Horizontal Rotation Range
360°
Tilt Rotation Range
93°
Auto Flip
Horizontal 180°, Vertical 180°
Ratio Speed
Supported
PWR on Action
Memory/NOP/A-B scan/360/Home/Tour 1-3
360° Scan Flip Range
0°-93° selectable
A-B Scan
User programmable
A-B Scan Speed
1-64 speed selectable
A-B Scan Dwell
2-60s selectable
360° Scan Speed
1-64 speedss
Dwell Preset
1-60s interval selectable
Preset Points
63
Go to Preset Speed
1-64 speedss selectable
Guard Tours
3 groups (16 points / group)
Park Action Mode
A-B scan / 360 / Home / Tour 1-3 / Save action
Park Time
1-60mins selectable
Park Action
User programmable
Communication Protocol
Pelco-D, Pelco-P
Communication
RS485 Bus
Baud Rate
1200/2400/4800/9600bps
Dome ID
DIP ID on Dome: 001-255; Soft ID in Menu: 001-250
Privacy Mask
Not supported on this version
Alarm
Not supported on this version
OSD Menu
Multiple Language (P/N customization)
Operating Temperature
20°F~ 140°F
Operating Humidity
≤95% Non Condensing
Heater & Blower
Auto temperature control
Waterproof
None –For indoor use only
Power
AC24V ≤3A
Lightning Protection
Transient voltage 6000V
Power Consumption
≤ 20W
Compatible Camera
SONY, LG, CNB, SAMSUNG, etc. (Optional)

3
Installation
DIP Switch Settings
Preparation
Before installation, make sure that the protocol, baud rate and address code used by the
product is fully consistent with the PTZ control device. The corresponding DIP switch diagram
can be seen below:
Address Settings
DIP switch SW1 is for the address settings of camera. OFF status means 0 while ON status
means 1.
(See illustration above) Turn on the 1st and 3rd (allocated to ON position) and get the binary
code 00000101, so the correspondence address is 5.
Detailed settings please refer to the back “Address Code Mapping Table”(appendix Ⅳ).
Baud Rate Settings
The 4thand 5th DIP Switches of the “FUN SW 2”set the Baud rate. Factory-default setting is
2400bps.
Baud rate: 1200bps、2400bps、4800bps、9600bps selectable. See next page for DIP switch
settings.

4
RS-485 Bus Matching Resistance
The 8th bit of DIP switch SW2 is to select the matching resistor. To the control center, in order to
prevent the reflection and interference of RS-485 communication signal and other signals, the
parallel matching resistor is needed in the communication interface of the dome camera at the
end away from the control center.
]
Connection
Connection of RS485
Before connecting, please turn off the power and carefully read the instructions of all connected
devices.

5
Function Instruction
Power Up Action
Power Up Self Testing Pan, Tilt, Camera Self-test Completion
Pan action: Pan & rotate, then stop at the zero coordinate.
Tilt action: Tilt, then stop at the zero coordinate
Lens action: Lens zooms out to the widest angle.
After completing the above actions, the power up self-testing finishes.
Basic Function
Dome Running
Control the joystick up, down, left and right on the PTZ keyboard.
Zoom
Press ZOOM- button to “zoom out”and obtain a wider field of view..
Press ZOOM+ button to “zoom in”and obtain a narrower field of view on distant subjects.
Focus
After FOCUS- button is pressed, objects closer to the camera will become clearer while objects
far away will become blurred.
After FOCUS+ button is pressed, objects farther away from the camera will become clearer
while objects close to the camera will become blurred.
Iris
Press IRIS- to shrink the iris and decrease the image brightness.
Press IRIS+ to enlarge the iris and increase the image brightness.
<SYSTEM>
MFG
PROTOCOL ATUO
DOME ID
COMM
VERSION
DETECTING
<SYSTEM>
MFG
PROTOCOL ATUO
DOME ID
COMM
VERSION
PAN: XXX TILT: XXX

6
Special Functions
The follow presets are predefined as special functions. “Call”these preset numbers to enable
those functions：
Screen Character Operation
Call preset 95 to enter the OSD, call preset 94 to exit the OSD.
Up or Down : Move the option of the OSD, change the value on the OSD.
Right ：Enter the option, select the item or confirm.
Left：Return to main menu or cancel
Note: 1. Items with“< >” means they have a sub menu.
PREST
FUNCTION
PRESET
FUNCTION
33
Pan scan180 º
88
Freeze on
34
Reset
89
Freeze off
79
Digital zoom on
92
A-B scan
80
Digital zoom off
94
OSD off
81
Auto day/night
95
OSD on
82
Switch to night
96
Guard tour 3
83
Switch to day
97
Guard tour 2
86
BLC on
98
Guard tour 1
87
BLC off
99
Pan scan

7
OSD Menu
Menu Index

8
fig 4.1.1 Get into the Menu Screen
System Information
Fig 4.2.1
MFG：Max 15 characters display on the screen.
PROTOCOL：Display the protocol of the dome
<MAIN MENU>
<SYSTEM>
<DOME>
<CAMERA>
<LANGUAGE>
<DISPLAY>
<RESET>
EXIT
<SYSTEM>
MFG
PROTOCOL AUTO
DOME ID 001
COMM 2400.N.1
VERSION
EXIT

9
DOME ID：Display the dome address.
COMM: Format: Baud rate, Check bit, Data bit, Start bit
VERSION: The current software version
Note: Protocol, ID and COMM all can be set in menu <COMM>.
Dome
Fig 4.3.1
Communication
Fig 4.3.1.1 Fig 4.3.1.2
<DOME>
<COMM>
<GUARD TOURS>
<A-B SCAN>
<PAN SCAN>
<PARK ACTION>
<PRIVACY ZONE>
<ALARM>
<ADVANCED>
EXIT
<COMM>
DEVICE ID
CHECK ID 0000
TARGET ID 001
SOFT PROTOCOL AUTO
BAUD RATE 2400BPS
<COMM RESET>
SAVE
EXIT
<COMM RESET>
RESET TO DIAL THE CODE
YES
EXIT

10
DEVICE ID
Each dome will have its own unique ID number.
CHECK ID
Enter the device ID above in this field, to tell all domes in the system which specific unit you
would like to make changes to.
TARGET ID
Target ID is available from 001 to 250.
SOFT PROTOCOL
Soft protocol is auto, Pelco-D and Pelco-P available
BAUD RATE
1200BPS、2400BPS、4800BPS、9600BPS available
COMM RESET
As shown in fig 4.3.1.2, Entering “YES”to reboot the dome and reset it to use the baud rate and
address set by the DIP switches.
SAVE
All changes must be saved. After saving, the dome will reboot.
Note: The factory default of this dome camera is to use the hardware DIP switch settings. After
the COMM. is changed in menu, it won’t be effective until saved. If it is desired to use the
hardware DIP settings again, run the COMM RESET.
Guard Tours
Fig 4.3.2.1 Fig 4.3.2.2
<GUARD TOURS>
GUARD TOUR 01
<SETTING>
INIT
RUNNING
DELETE
EXIT
<GUARD TOUR 01>
ID POINT TIME(S) SPEED
1 01 06 64
2 02 06 64
3 03 06 64
4 04 06 64
5 05 06 64
6 06 06 64
7 07 06 64
8 08 06 64

11
GUARD TOUR
Total 3 guard tours selectable: 01, 02, 03.
SETTING
Each guard tour includes max 16 presets. The number of the preset is from 1 ~ 63. Dwell time
is 1 to 60s selectable. Speed is 1 to 64 speeds selectable.
INIT
After init, preset point, dwell time, speed will resume to the default setting.
RUNNING (RUN)
Runs the present guard tour.
DELETE
Delete the guard tour set. After deleting, the preset points all display as “0”. Please note the
actual presets are not removed from the camera, they are just removed from this one tour.
A-B Scan
Fig. 4.3.3.1 Fig. 4.3.3.2
PRESETA
On A-B scan, A point can be preset from 0 to 64.
PRESET B
On A-B scan, B point can be preset from 0 to 64.
SCAN SPEED
A-B scan speed is 1 to 64 speeds, selectable.
DWELL TIME
Dwell time between A to B is 2s to 60s selectable.
RUNNING
Run the A-B scan. Check Fig. 4.3.4.2.
<A-B SCAN>
PRESETA 01
PRESET B 02
SCAN SPEED 20
DWELL TIME 06S
RUNNING
DELETE
EXIT
A-B SCAN
RUNNING…
LEFT KEY TO EXIT
PAN：XXX TILT：XX

12
DELETE
Delete the presets from the A-B scan. After deleting, the preset points all display as “0”. Please
note the actual presets are not removed from the camera, they are just removed from the A-B
scan.
Pan Scan
Fig. 4.3.4.1 Fig. 4.3.4.2
PAN SCAN SPEED
Pan scan speed is 1 to 64 speeds selectable.
INIT
Reset the scan speed and tilt degree to the default setting.
RUNNING
Run the scan, using the speed and tilt degree which were set.
Park Action
Fig. 4.3.5.1 Fig. 4.3.5.2
PARK MODE
Park mode includes OFF, Park action, A-B scan, Pan scan, guard tour01, guard tour02, guard
tour03 and Preserve action.
<PAN SCAN>
PAN SCAN SPEED 20
INIT
RUNNING
EXIT
PAN SCAN
RUNNING…
LEFT KEY TO EXIT
PAN：XXX TILT：XX
<PARK ACTION>
PARK MODE OFF
PARK TIME 01M
<SETTING>
RUNNING
DELETE
EXIT
<PARK ACTION>
PRESET 1: SAVE
PRESET 2: BACK

13
When park mode is OFF status, the dome doesn’t run park mode.
When park mode is PRESERVE ACTION status, it remembers the previous action (A-B scan,
Pan scan, Guard tour 01, Guard tour 02, Guard tour 03).
Example: If the A-B scan was previously used, when the action stops unexpectedly, the camera
enters the park mode to continue to run the A-B scan.
PARK TIME
Park time is 01~60 minutes selectable.
SETTING
After entering the OSD menu, as 7.4.8.2, move to the desired position and save the settings.
RUNNING
Starts the park action. if there is no setting, the system will display a reminder: “Please set park
action”.
DELETE
Delete the settings.
Privacy Zone
Privacy zones are not supported on this version of this camera.
Alarm (Optional)
Alarm functions are not supported on this version of this camera.
Advanced
Fig. 4.3.8.1
PWR ON ACTION
Power on action can be set as Memory, A-B scan, Pan scan, Park action, Guard tour 01, Guard
tour 02, Guard tour 03 and No action.
<ADVANCED>
PWR ON ACTION MEMORY
RATIO SPEED ON
AUTO FLIP ON
<OTHERS>
EXIT

14
RATIO SPEED
Ratio speed can be set as ON or OFF status.
AUTO FLIP
Auto flip can be set as ON or OFF status.
OTHERS
Set other options.
Camera
Fig. 4.4.1
CAM
Display the information of module supported by this dome.
ZOOM SPEED
Zoom speed is quick and slow selectable.
DIGITAL ZOOM
Digital zoom is on/off selectable.
FOCUS
Focus is auto and manual selectable
IRIS
Iris is auto and manual selectable
BLC
BLC is ON and OFF selectable
FREEZE
<CAMERA>
CAM AUTO
ZOOM SPEED QUICK
DIGITAL ZOOM OFF
FOCUS AUTO
IRIS AUTO
BLC OFF
FREEZE OFF
EXIT

15
Video freeze is ON and OFF selectable
Note: Depending on the installed camera module, the CAMERA MENU may not be supported.
Language
Fig. 4.5.1
LANGUAGE
Language can be set as Chinese or English. The default setting is English.
Display
Fig. 4.6.1
SYSTEM
Video system includes NTSC and PAL. N means NTSC and P means PAL.
PAND T
Enable or disable the display of the Pan and Tilt degrees on screen.
ACTION
Enable or disable the display of the current action on screen, such as A-B scan, preset recall
etc..
DOME ID
Enable or disable the display of the dome’s ID number on screen.
<LANGUAGE>
LANGUAGE ENGLISH
EXIT
<DISPLAY>
SYSTEM PAL
PAND T ON
ACTION ON
DOME ID ON
COMM ON
EXIT

16
COMM
Enable or disable the display of the dome’s communication settings on screen
Reset
CONFIRM: Delete the user-created preset
information saved in the dome.
<RESET>
<DOME RESTART>
<SYS DATA>
<CAM DATA>
<PRESET>
EXIT
<DOME RESTART>
CONFIRM: Save data,
dome restart
EXIT
<SYS DATA>
CONFIRM：Factory default
EXIT
<CAM DATA>
CONFIRM：Factory default
EXIT
<PRESET>
CONFIRM：DELALL PRESETS
CONFIRM 1：DEL 01 TO 16
CONFIRM 2：DEL 17 TO 32
CONFIRM 3：DEL 33 TO 48
CONFIRM 4：DEL 49 TO 96
EXIT

17
Auto Temperature Control
This product has a built-in fan and heater, which automatically cool or heat through a
temperature sensing circuit inside the dome.
Appendix ⅠAnti-lightning, Anti-surge
This product has lightning protection with TVS tube technology, which can effectively
prevent the transient lightning below 3000V, surge and damages caused by other types of
pulse signals.
However, necessary protective measures should be made to ensure electrical safety for
outdoor installation according to the actual situation.
·Signal transmission line must be at least 50 meters away from any high-voltage
equipment or high voltage cable.
· In areas with high induced voltage (such as high voltage substations), installation of
additional high power lightning protection equipment and lightning rod must be taken.
· Lightning protection and grounding of outdoor devices and lines must take the
lightning-protection requirements of buildings into consideration, and comply with the related
national standards and industry standards.
· System must be equipotential grounding. Grounding device must meet dual requirements
of anti-interference and electrical safety, and should not be shorted or mixed with the adjacent
lines. When system is independently grounded, grounding impedance should be less than 4Ω,
and cross-sectional area of grounding conductor must be not less than 25m2.
Fig 25
Appendix ⅡClean Transparent Cover
In order to assure a clear image, the cover of the dome should be cleaned regularly.
● Be careful when cleaning and hold the outer ring of the cover to avoid directly touching the
domet.

18
● Please use a soft dry cloth to wipe internal and external surfaces.
●If dirt is serious, a mild detergent may be used.
Appendix ⅢCommon Knowledge on RS-485 Bus
1. Basic Feature of RS-485bus
According to industry bus standard of RS-485, RS-485 bus is half-duplex communication bus
with the characteristic impedance of 120Ω, whose maximum load capacity is 32 payloads
(including the master device and the controlled device).
2. Mode of Connection and Terminal Resistance
2.1 Industry standard of the RS485 bus requires that a daisy chain connection mode should
be used between the devices with 120Ω terminal resistances connected at the both ends.
As shown in fig. 26 and fig. 27, the distance of part "D" shall not beyond 7 meters.
Fig 26 Fig 27
2.2 120Ω terminal resistance is connected as shown in fig 27.
120Ω terminal resistance is available in the circuit board and the connection is shown as
following:
When needing to connect 120Ω resistance, toggle the 8th bit of DIP switch SW2 to "ON" .The
120Ω resistance will be connected to the circuit.
AppendixⅣAddress Code Mapping Table