Seedsware EMG7 User manual

-1- 12A4A4-00023E-5
EM Series Gesture Model
7”Wide Windows CE Embedded
Panel Computer
EMG7
EMG7-W207A8-0024-x11-01
Instruction Manual
Seedsware Corporation
http://www.seedsware.co.jp/global

-2- 12A4A4-00023E-5
Table of Contents
Introduction............................................................................................................................................ 41. Notes..................................................................................................................................................... 42. Precautions for safe use........................................................................................................................ 43.3-1 Warnings .......................................................................................................................................... 5
3-2 Cautions ........................................................................................................................................... 6
3-3 Handling of LCDs ............................................................................................................................. 8
3-4 Handling of Touch Screens.............................................................................................................. 8
3-5 Handling of SD card ......................................................................................................................... 9
3-6 Handling of Batteries........................................................................................................................ 9
Items Included in Package.................................................................................................................. 104. Names of Parts.................................................................................................................................... 115.5-1 Front............................................................................................................................................... 11
5-2 Back................................................................................................................................................ 11
5-3 Right............................................................................................................................................... 12
5-4 Top................................................................................................................................................. 12
5-5 Bottom............................................................................................................................................ 12
External Interface................................................................................................................................ 136.6-1 SD Card Slot................................................................................................................................... 13
6-2 Serial Port (COM1)......................................................................................................................... 13
6-3 Ethernet.......................................................................................................................................... 13
6-4 USB Host Port................................................................................................................................ 14
6-5 USB Device Port............................................................................................................................. 14
6-6 Audio Interface (LINE OUT) ........................................................................................................... 15
6-7 Audio Interface (MIC IN)................................................................................................................. 15
6-8 Power Connector............................................................................................................................ 15
Specification........................................................................................................................................ 167.7-1 General Specification ..................................................................................................................... 16
7-2 Environmental Specification........................................................................................................... 16
7-3 Installation Specification................................................................................................................. 17
Installation........................................................................................................................................... 188.8-1 Installation Conditions .................................................................................................................... 18
8-2 Panel Mounting............................................................................................................................... 19
8-2-1 Panel Dimension...................................................................................................................... 19
8-2-2 Installing the Gasket................................................................................................................ 19
8-2-3 Installation Procedure.............................................................................................................. 20
8-3 Mounting to a “VESA” Arm ............................................................................................................. 21
Wiring.................................................................................................................................................. 229.9-1 Using Accessory Connectors........................................................................................................ 22
9-2 Cautions for Power Supply Wiring.................................................................................................. 23
9-3 Cautions for Grounding .................................................................................................................. 23
9-4 Caution for Wiring of Signal Lines .................................................................................................. 23
Inserting and Removing the SD Memory Card................................................................................ 2410.
10-1 Inserting the Memory Card........................................................................................................... 24
10-2 Removing the SD Memory Card................................................................................................... 25

-3- 12A4A4-00023E-5
Connecting and Changing of Batteries............................................................................................ 2611.
11-1 Battery Connecting and Changing Procedure.............................................................................. 26
Applying Protection Sheet............................................................................................................... 2812.
12-1 Application Procedure .................................................................................................................. 28
Calibration....................................................................................................................................... 2913.
13-1 Sensor Sensitivity Calibration....................................................................................................... 29
13-1-1 Sensor Sensitivity Calibration Procedure (by switch)............................................................. 29
13-2 Coordinate Calibration.................................................................................................................. 30
Starting Method............................................................................................................................... 3114. Maintenance.................................................................................................................................... 3115.
15-1 Display.......................................................................................................................................... 31
15-2 Regular Maintenance ................................................................................................................... 31
15-3 Changing of Batteries...................................................................................................................... 31
Compatible Standards..................................................................................................................... 3216.
16-1 UL Standards................................................................................................................................ 32
16-2 CE Marking................................................................................................................................... 32
16-3 RoHS Directive............................................................................................................................. 32
16-4 FCC.............................................................................................................................................. 32
List of Option................................................................................................................................... 3317. Warranty and Repair ....................................................................................................................... 3418.
18-1 Inquires......................................................................................................................................... 34
18-2 Warranty....................................................................................................................................... 34
18-3 Production Discontinuance........................................................................................................... 34
18-4 Repair Condition........................................................................................................................... 34
Others.............................................................................................................................................. 3519.
Appendix: Outline drawing (SM3-001905-10)

-4- 12A4A4-00023E-5
Introduction1.
Thank you for choosing Seedsware products.
Please read this manual carefully and use the product correctly.
Notes2.
Reproduction and/or duplication of this product and/or this manual, in any form, in whole or in part, without
permission is strictly prohibited.
Contents of this product and/or this manual are subject to change without previous notice .
Although all efforts have been made to ensure the accuracy of this product and/or the contents of this
manual, should you notice any errors or have any questions, feel free to contact and notify us.
Seedsware shall not be held liable in any way for damages or losses, nor be held responsible for any claims
by a third party as a result of using this product.
Precautions for safe use3.
Precautions are noted in this manual in order for the product to be used safely. Read this manual along with other
related manuals carefully to understand the correct handling and functions of the EMG7.
Safety Symbol Legends
Safety symbols listed below are noted throughout this manual for the EMG7 to be used correctly and safely. These
symbols stand for very important safety information as noted below:
Warning
Indicates a procedure, condition, or statement that, if not strictly observed, could
result in severe human injuries or loss of life.
Caution
Indicates a procedure, condition, or statement that, if not strictly observed, could
result in human injuries or property damage.
Indicates a procedure, condition, or statement that is strictly prohibited for correct use of the
equipment. (Forbidden)
Indicates a procedure, condition, or statement that should be strictly followed for correct use
of the equipment. (Mandatory)

-5- 12A4A4-00023E-5
3-1 Warnings
Warning!
Warnings for Design
Designing switches that can cause human injuries and/or property damages on the Touch Screen is strictly
prohibited. Unintentional output signals due to malfunction of the main body, units, and/or cables can cause
serious injuries. Design the system so that switches with major functions are equipped on devices other than
the EMG7 itself.
Designing safety related switches on EMG7 is prohibited. Switches related to safety,such as emergency stop
switches, should be made on a different hardware.
Design the system so there is no malfunctions due to communication anomalies between the host controller
and the EMG7. It can cause human injuries and/or property damages.
Do not use EMG7 as a major warning device that may cause injuries/serious material damages, and or
production stoppage. Control devices related to critical warning displays and warnings should be structured
on an independent, redundant hardware system or a mechanical interlock.
EMG7 is not intended for use for aircraft equipment, aerospace instruments, trunk line communication
equipment, nuclear powercontrol equipment, and medical equipment that concerns life support, and or other
equipment that concerns high reliability and safety. It cannot be used for these purposes.
When using the EMG7 for purposes that concern high reliability and safety of functions and accuracy, such
as transport equipment (trains, automobiles, ships, etc.), crime/disaster prevention devices, various safety
devices, and medical equipment that does not concern life support, be sure to have safety features including
redundancy and false operation prevention measures incorporated into the entire system.
Display will black out when the backlight goes out. If mistakenly operated in this condition, it might result in
improper operation. Do not design touch-switches that might cause human injuries and material damages on
the EMG7:
Below symptoms will occur when the backlight goes out:
1: Display goes out when “backlight off” function is not set.
2: Display does not recover when display is touched after display goes out with “backlight off” function set.
Warnings for Handling
Do not modify/disassemble the EMG7. It may cause fire and/or electric shocks.
Do not use around flammable gas. It may cause explosions.
Do not put any kind of liquid, such as water, and metals in to the product. It may cause fires and/or electric
shocks.

-6- 12A4A4-00023E-5
Warnings for Wiring
For wiring and installation, please refer to the manual ad specification in order to conduct it correctly. It may
cause fires and/or electric shocks.
Before installing the power cable, make sure power is not being supplied from power source. It may cause
electric shocks.
Do not use power voltage other than what is specified. It may cause fires and/or electric shocks.
Warnings for Applying Current and Maintenance
Do not insert and remove communication cable while applying power.
EMG7 uses lithium batteries for the clock and part of memory back-up. Batteries may need to be replaced
after prolonged use. If replacement is necessary, please do refer to the instructions correctly.
3-2 Cautions
Caution!
Cautions for installation
Make sure cables are securely connected to connectors to avoid wrong input and output due to loose
connection.
Cautions for Applying Current and Maintenance
During access to SD card, do not turn off the EMG7 or pull out the SD card. It might damage the data inside
of the SD card.
Cautions for Wiring
Use D type grounding dedicated to EMG7 for FG terminals. It may cause electric shocks or malfunctions.
Make sure chips and objects from wiring do not enter the EMG7. It may cause fire or malfunctions.
Cautions for Disposal
When disposing the product, please treat is as industrial waste.

-7- 12A4A4-00023E-5
Precautions for Safe Use
Do not press down hard on the display area of EMG7 with hard objects. It may break the LCD panel and may
cause injuries. Also, do not press down on the panel with sharp objects such as mechanical pencils or
drivers. It may damage the displays.
Installing EMG7 in areas out of the range of the specification will cause failures.
Do not use in areas where temperature rises and dwells rapidly. It may cause failures.
Avoid areas where rapid temperature change could cause condensation. It may cause failures.
Do not put any kind of liquid, such as water, or any metal parts into EMG7. It may cause failures or electric
shocks.
Do not use or keep EMG7 in locations with exposure to direct sunlight, high temperature, fine particles,
humidity, and/or vibrations.
Do not use or keep in areas where gasified chemicals are exuded into the air, or where chemical
contamination can occur.
Acid, Alkali, other saline chemicals: Failures due to corrosion
Organic solvents: Fire
If the surface of EMG7 gets dirty, wipe with a dry, soft cloth damped with a neutral detergent then wrung dry.
Do not use thinner or organic solvents.
LCD of display will deteriorate with ultraviolet rays. Do not use or keep in areas under strong ultraviolet rays.
When stored in sub-ambient temperature, LCD of display might coagulate and cause damage to the panel.
Also, when stored in over-ambient temperature, the LCD will turn into isotropic liquid and will not turn back to
its original state. Please store in specified ambient temperature.
After turning off the power of EMG7, leave for a while before turning the power back on. It might not function
normally.
Be sure to take back-up assuming the loss of data in the EMG7 in an event of an unexpected accident.

-8- 12A4A4-00023E-5
3-3 Handling of LCDs
1) The LCD display contains skin-irritating materials. If liquid materials flow out due to damage and comes in
contact with skin, wash the area under running water for at least 15 minutes and consult a doctor.
2) The LCD display might have uneven brightness according to the contents being displayed. This is not a
malfunction.
3) Minute spots (dark or bright) may occur in the LCD display elements. This is a basic characteristic of the
LCD display and not a malfunction.
4) When LCD display is viewed outside the specified view angel, the color might seem different. This is a basic
characteristic of the LCD display and not a malfunction.
5) When displaying a same image for a long period of time, it might cause an image lag. This is a basic
characteristic of the LCD display and not a malfunction.
In order to avoid image lags, please follow the below procedures:
1. When leaving the same image displayed, use the” display off” function.
2. Change the image displayed periodically and do not display the same image for a long period of time.
3-4 Handling of Touch Screens
1) If elements that change ambient environments or electric fields (capacitors with large capacity, power units,
and materials with high permittivity such as metals) are set close to the product, it might have impact to the
coordinate detection. Make sure to keep a good distance from the above unstable elements as much as
possible when designing.
2) Due to the characteristics of the touch screen, its functions might become unstable according to the
environment it is installed. For correct operations, perform sensitivity sensor calibration when building into a
device.
Also if at any time the touch screen operation become unstable due to changes in environment or
installation conditions, perform sensitivity sensor calibration.
3) The touch screen surface is made of glass. Glass is subject to break once scratched. Please handle with
care and avoid glass from contacting other glass and hard objects.
4) Touch screen may not operate correctly when there is moisture on the surface.
When moisture is detected on the touch screen surface, please wipe it dry before use.
5) When designing applications, consider the fact that area slightly outside the display might be read as a
coordinate due to the characteristics of the touch screen when touched.

-9- 12A4A4-00023E-5
3-5 Handling of SD card
1) Use a computer for important data and take backup to an outside media (hard disc, CD-R, etc.) regularly.
We will not be held liable for any data lost or changed that is registered in the SD card.
2) Do not remove the SD card or turn the unit power off during write or read. It may cause the data inside the
unit or the SD card to be lost or damaged (deleted).
3) Please keep the socket terminal of the memory cards and SD card clear of foreign objects.
4) Do not touch the terminals with fingers or metal objects. It may cause malfunctions.
5) When inserting the SD card, make sure it is inserted in the correct direction.
6) Do not apply undue force when inserting/removing.
7) Do not insert anything other than a SD card into the SD card socket. Also be careful of any foreign objects
entering the socket.
8) Do not bend, break, or place under heavy objects.
9) Do not place in areas with sudden temperature change. Condensing will cause malfunctions.
10) Do not place in areas near corrosive chemicals or where corrosive gases evolve. It may cause malfunctions.
11) When cleaning, wipe with a dry soft cloth.
12) When carrying and storing, place the SD card memory card in its protection case
3-6 Handling of Batteries
1) This product uses primary batteries. Recharging is prohibited
2) Insulate the terminals with tape when discarding.
It may generate heat, explode, or ignite if in contact with other batteries or metal objects.
Be sure to follow the instructions of the local government (restrictions of the district) when discarding.
3) Check the polarity and make sure it is connected in the correct direction
4) Do not store in areas with direct sunlight, high temperature and/or high humidity
5) Disassembling and modifying is prohibited.
6) Do not change the batteries with wet hands
7) Please do not use other than the supplied battery.
8) Installing the battery should only be performed by trained personnel.
9) If the EM is VESA mounted, detach from the VESA arm when replacing the battery. Refer to the section,
Mounting on a VESA arm.
10) The battery should only be installed when the unit is powered off.
11) Do not use any metallic item to remove the battery (such as screwdrivers, knives, pliers, and so forth).
12) Be careful to not drop the battery or any associated screws into the unit.
13) Be careful of edges on internal sides of the enclosure and frame.

-10- 12A4A4-00023E-5
Items Included in Package4.
Below are included in the package. Please check before use.
・EMG7 Main Unit 1unit
・Mounting Bracket (IS-TK-01) (4pcs/set) ・Battery (SWBT-01) (1)
・Protection Sheet (SWCA-7WS00-001) (1) ・Waterproof GasketSWPK-7W-01）(1)
*Already installed to unit
・Power Connector (SWCN-01-03) (1) ・Serial Connector (SWCN-01-05) (1)
・Installation Guide (2) *1・Accessory List (2) *1
*1. 1 English version and 1 Japanese version.
＜Note＞
Although efforts have been made to ensure quality and packaging at shipment, should you notice any damage or a
shortage of parts, please contact a dealer or Seedsware for additional instructions before use.

-11- 12A4A4-00023E-5
Names of Parts5.
5-1 Front
A) Status LED
The status LED displays the state of the EMG by the LED color shown below:
LED State
EMG State
Off
Power not applied
Amber, steady
OS starting
Green, steady
Normal operating state
Green, blinking
Backlight off
(Normal Operation)
5-2 Back
B) Battery Cover
C) License Seal
D) Product label
E) FCC label
A
B
C
D
E

-12- 12A4A4-00023E-5
5-3 Right
F) SD Card Slot
G) USB Device
H) Audio Interface (LINE OUT)
I) Audio Interface (MIC IN)
5-4 Top
J) Mounting Holes
5-5 Bottom
K) Power Input
L) Ethernet
M) USB Host
N) Serial Port（COM1）
O) Mounting Holes
F
G
H
I
J
J
K
L
M
N
O
O

-13- 12A4A4-00023E-5
External Interface6.
6-1 SD Card Slot
Connector : SD / SDHC memory card (Push-in/push-out method)
Corresponding media : SD/SDHC memory card
Maximum capacity : 32GB
6-2 Serial Port (COM1)
Serial port : RS232C
Connector : Euro terminal connector (<Tyco Electronics> 284539-5)
Recommended cable connector : SWCN-01-05(<Tyco Electronics>284510-5) *Included as accessory.
PIN No.
Signal
Schematic
1
TXD
2
RXD
3
RTS
4
CTS
5
SG
6-3 Ethernet
Ethernet : 10BASE-T/100BASE-TX
Connector : RJ-45
PIN No.
Signal
Schematic
1
TX+
2
TX-
3
RX+
4
NC※1
5
NC※1
6
RX-
7
NC※1
8
NC※1
*1. NC is ‘not connected’.
Status LED
LED State
State
On, Green
LINK/ACT
On, Yellow
SPEED
Compatible cable : Above category 5
8
1
GREEN
YELLOW
1
5

-14- 12A4A4-00023E-5
6-4 USB Host Port
Interface : USB2.0
Number of Ports : 2
Connector : Type-A
Maximum supply current: 0.5A / Port
PIN No.
Signal
(All ports common)
Schematic
1
USB_VCC
2
D-
3
D+
4
SG
6-5 USB Device Port
Interface : USB2.0
Connector : Type-B Mini connector
PIN No.
Signal
Schematic
1
USB_VCC
2
D-
3
D+
4
NC※1
5
SG
※1NC is “Not Connected”
1
4
1
4
1
5

-15- 12A4A4-00023E-5
6-6 Audio Interface (LINE OUT)
Interface : LINE OUT (Stereo)
Connector : φ3.5 Stereo JACK
Maximum output level : 1Vrms
Use built-in amplifier when connecting to speakers.
PIN No.
Signal
Schematic
1
SG
2
Lineout R
3
Lineout L
6-7 Audio Interface (MIC IN)
Interface : MIC IN (Mono)
Connector : φ3.5 Stereo JACK
Maximum input level : 250mVrms
PIN No.
Signal
Schematic
1
SG
2
NC※1
3
MIC
※1NC is “Not Connected”.
6-8 Power Connector
Interface : 24VDC IN
Connector : Euro terminal connector (<Tyco Electronics>284510-3)
Recommended cable connector : SWCN-01-03(<Tyco Electronics>284510-3) *Included as accessory.
PIN No.
Signal
Schematic
1
FG
2
GND
3
+24VDC
1
2
3
1
2
3
1
3

-16- 12A4A4-00023E-5
Specification7.
7-1 General Specification
Item
Specification
Power
Voltage Rating
24VDC
Voltage Allowance Range
24VDC±20%
Power Consumption※1
15W or under（Typ. 7W）
FG Connection
FG (Frame GND) and SG (Signal GND) are
connected internally.
FG (Frame GND) and GND are not connected.
※1Power consumption for EMG7 unit only. Consider the power consumption of USB devices when
connecting the USB.
7-2 Environmental Specification
Item
Specification
Ambient Operating Temperature
(inside of panel and display surface)
0℃to 55℃
Ambient Storage Temperature
-10℃to +60℃
Ambient Operating Humidity
10%RH to 85%RH
(non-condensing. Wet-bulb temperature is 39 ℃or less)
Ambient Storing temperature
10%RH to 85%RH
(non-condensing. Wet-bulb temperature is 39 ℃or less)
Dust
Prohibited
Corrosive Gas
Corrosive gas Prohibited
Environment
Pollution Degree 2, Indoor use
Pressure Resistance
(Frequency of Use)
800hPa to 1114hPa (Altitude up to 2000m)
Vibration Resistance
IEC61131-2(JIS B 3502) compliant
5Hz to 9Hz Single amplitude 3.5mm
9Hz to 150Hz Fixed acceleration 9.8m/s２
X,Y,Z directions for 10times(100min.)

-17- 12A4A4-00023E-5
7-3 Installation Specification
Item
Specification
Grounding
Grounding resistance of 100Ω, 2mm2[0.0062inch2] or thicker
wire, or your country’s applicable standard.
Structure
Protection Structure: IP65 *1
(Front side only when mounted to panel)
Installation : Panel mounting
Cooling Method
Natural Convection
Weight
App. 700g
Exterior Measurement
192(W) x 137(H) x 36(D) mm
Panel Cut
183.5 ＋0.5/-0 (W) x 128.5 ＋0.5/-0 (H) mm
※1Protection structure of front surface when installed in a panel. It has been tested to verify compliance but
does not guarantee for all environmental use. Especially for oils defined in the test, in cases where
prolonged exposure to vaporized oils or cutting fluids with especially low viscosity, oil might enter to front
area through area where touch screen has lifted and may need special measurements. Please check the
installation environment prior to the use of EMG7.
Also, gaskets that have been used for a long time, or gaskets that have once been applied to panels, the
original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to
replace the gasket regularly.

-18- 12A4A4-00023E-5
Installation8.
8-1 Installation Conditions
・When mounting to panel, be sure to have enough room to insert and remove the SD card, cables, and mounting
brackets.
・Consider specification temperature between EMG7 and the structure and parts. Be sure to have good ventilation.
・Please use in ambient temperature of 0 to 55℃and ambient humidity of 10 to 85％RH(Wet bulb temperature is
39℃or less)
・Ambient operation temperature indicates the temperature inside the cabinet where it is installed as well as the
panel surface.
・EMG7 should not be mounted at an angle more than 30° from vertical state as illustrated in the following figure.
・When installing the EMG7 in a slanted panel of angle 30 degrees or more, please use forced air cooling to
ensure the temperature specification
Inside Cabinet
Panel surface
30°or less

-19- 12A4A4-00023E-5
8-2 Panel Mounting
8-2-1 Panel Dimension
Panel thickness range: 1.0 ㎜to 5.0 ㎜
Panel opening size：183.5×128.5mm
The material of the mounting panel, please use the metal.
Be recommended panel thickness range, depending on material and size,
may not maintain the strength when an impact is applied.
Please do take into account, such as reinforcement in the environment impact, such as join.
There is a possibility of personal injury or product damage when dropped product,
Please be careful not to drop.
8-2-2 Installing the Gasket
Please install the gasket even in environments where it may not seem necessary.
※Gasket will be installed to the unit before shipment.
Please make sure it is properly installed before use.
-0
+0 . 5
183.5
128.5 -0
+ 0 .5
4-R3以 下
Gasket
Groove
Insert gasket along the groove.
Under 4-R3

-20- 12A4A4-00023E-5
8-2-3 Installation Procedure
①Install unit (with gasket installed) to the panel from the front.
*Make sure it is installed in the correct direction
②Insert mounting hook in the mounting holes in the four locations of the unit.
Top
Bottom
③Tighten screw of mounting bracket and slide the bracket.
Tighten the screws a little at a time in all four locations working diagonally.
Appropriate torque for tightening is 0.3N･m.
Note
・If the screw of the mounting bracket is not perpendicular to the panel, the unit might fall off the panel .
・If screw is too tight, the unit might deform or damage. Please tighten with appropriate torque
Panel
Main Unit
Mounting Bracket
Mounting holes