protech SG-S156 User manual

USER
MANUAL
15” / 17” / 21.5” Intel®7th Gen. Core
TM
i5-7300U /
Pentium 4415U Processor Fanless and All-around
IP66/IP69K Stainless Panel PC
SG-S156 / SG-S176 /
SG-S216
SG-S156 / SG-S176 / SG-S216 M2

SG-S156 / SG-S176 / SG-S216
15”/17”/21.5” Intel®7th
CoreTM i5-7300U / Pentium 4415U
Processor Fanless and All-around
IP66/IP69K Stainless Panel PC
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Jan. 2020. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery
only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
CAUTION: The waterproof capability of the device may be
incapable when the screws are loosened.
CAUTION: The O-ring to seal the device may be damaged
during the maintenance process. Qualified engineer is
recommended to make the O-ring replacement to keep the
waterproof capability of the device.
WARNING: Some internal parts of the system may have
high electrical voltage. We strongly recommend that only
qualified engineers are allowed to service and disassemble
the system. If any damages should occur on the system and
are caused by unauthorized servicing, it will not be covered
by the product warranty.

i
Contents
1Introduction ......................................................................................... 1-1
1.1 About This Manual .................................................................... 1-2
2Getting Started .................................................................................... 2-1
2.1 Packing List ............................................................................... 2-2
2.2 System Overview ...................................................................... 2-3
2.3 SG-S156 / SG-S176 / SG-S216 System Specifications ........... 2-9
2.4 Safety Precautions .................................................................. 2-11
3System Configuration......................................................................... 3-1
3.1 External System I/O Ports Diagram .......................................... 3-2
3.1.1 Rear I/O Ports Diagram ..................................................... 3-2
3.2 Jumper & Connector Quick Reference Table............................ 3-3
3.3 Component Locations ............................................................... 3-4
3.3.1 Top View of BE-0996 ......................................................... 3-4
3.3.2 Bottom View of BE-0996 ................................................... 3-5
3.4 How To Set Jumpers ................................................................. 3-6
3.5 Setting Main Board Connectors and Jumpers .......................... 3-8
3.5.1 COM2 Connector Pin9 Definition Selection Guide
(JP_COM2)........................................................................ 3-8
3.5.2 COM Connector (COM1, COM2) ...................................... 3-9
3.5.3 Dual USB 3.0 Ports (USB1) ............................................ 3-10
3.5.4 Dual USB 2.0 Ports (USB2, USB3) .................................3-10
3.5.5 Internal USB 2.0 Connector (JUSB1).............................. 3-11
3.5.6 LAN1, LAN2 Ports (LAN1, LAN2).................................... 3-12
3.5.7 DP and HDMI Port (J1).................................................... 3-13

ii
3.5.8 Digital Input / Output Connector (JDIO1) ........................3-14
3.5.9 HD Audio Connector (AUDIO1).......................................3-15
3.5.10 ATX Power Input Connector (ATX1)................................ 3-16
3.5.11 Speaker Connectors (SPK_L_OUT1, SPK_R_OUT1) ....3-17
3.5.12 Front Panel Connector (JFP1) ........................................ 3-18
3.5.13 CPU Fan Connector (CPU_FAN1) .................................. 3-18
3.5.14 SATA 3.0 Connector (SATA1) .......................................... 3-19
3.5.15 SATA Power Connector (JHDD_PWR1) .........................3-20
3.5.16 LVDS Connector (JLVDS1) ............................................. 3-21
3.5.17 Panel Inverter Connector (JINV1) ................................... 3-22
3.5.18 Mini PCI Express Slot (M_PCIE1)...................................3-23
3.5.19 mSATA Connector (M_SATA1)........................................ 3-24
3.5.20 I2C Wafer (JI2C1)............................................................ 3-25
3.5.21 SPI Connector (JP7)........................................................ 3-25
3.5.22 SPI Override Protection Selection (JP1) .........................3-26
3.5.23 Battery Wafer (JBAT1)..................................................... 3-27
3.5.24 Slide Switch For LVDS Resolution Selection (SW1) ....... 3-28
3.5.25 LVDS VCC Selection (JP5) ............................................. 3-31
3.5.26 Backlight PWM Level Selection (JP6) ............................. 3-32
3.5.27 V3P3 MPCIE Selection (JP9).......................................... 3-33
3.5.28 Clear CMOS Data Selection (JCMOS1).......................... 3-34
3.6 External M12 Waterproof Connectors.....................................3-35
3.6.1 USB 2.0 Connectors........................................................ 3-35
3.6.2 Power Button ................................................................... 3-35
3.6.3 LAN1, LAN2 Ports ........................................................... 3-36
3.6.4 COM Connector...............................................................3-37
3.6.5 DC Power Input Connector ............................................. 3-37
4Software Utilities ................................................................................. 4-1

iii
4.1Introduction................................................................................ 4-2
4.2 Installing Intel®Chipset Software Installation Utility .................. 4-3
4.3 Installing Graphics Driver Utility ................................................ 4-4
4.4 Installing Sound Driver Utility .................................................... 4-5
4.5 Intel®Management Engine Components Driver Installer Installation
................................................................................................... 4-6
4.6 Installing LAN Driver Utility........................................................ 4-7
4.7 Installing Intel®Serial I/O Driver Utility ...................................... 4-8
5BIOS SETUP ........................................................................................ 5-1
5.1 Introduction................................................................................ 5-2
5.2 Accessing Setup Utility.............................................................. 5-4
5.3 Main........................................................................................... 5-7
5.4 Advanced .................................................................................. 5-9
5.4.1 Advanced – CPU Configuration ......................................5-10
5.4.2 Advanced – SATA Configuration ..................................... 5-11
5.4.3 Advanced – PCH-FW Configuration................................ 5-12
5.4.4 Advanced – Trusted Computing ...................................... 5-13
5.4.5 Advanced – ACPI Settings .............................................. 5-15
5.4.6 Advanced – F81866 Super IO Configuration .................. 5-16
F81866 Super IO Configuration – Serial Port 1 Configuration .... 5-17
F81866 Super IO Configuration – Serial Port 2 Configuration .... 5-18
5.4.7 Advanced – Hardware Monitor........................................5-19
Smart Fan Mode Configuration ................................................... 5-20
5.4.8 Advanced – F81866 Watchdog .......................................5-21
5.4.9 Advanced – S5 RTC Wake Settings................................ 5-22
5.4.10 Advanced – USB Configuration....................................... 5-25
5.4.11 Advanced – Network Stack Configuration .......................5-26

iv
5.5 Chipset .................................................................................... 5-28
5.5.1 Chipset – System Agent (SA) Configuration ................... 5-29
System Agent (SA) Configuration – Memory Configuration ........ 5-30
5.5.2 Chipset – PCH IO Configuratioin..................................... 5-31
PCH-IO Configuration – PCI Express Configuration ...................5-32
5.6 Security ................................................................................... 5-33
5.7 Boot ......................................................................................... 5-35
5.8 Save & Exit.............................................................................. 5-36
Appendix A System Diagrams....................................................A-1
SG-S156 System Exploded Diagram .......................................................A-2
SG-S176 System Exploded Diagram .......................................................A-4
SG-S216 System Exploded Diagram .......................................................A-6
VESA Mount Installation Exploded Diagram ............................................A-8
Stand Kit Installation Exploded Diagram ..................................................A-9
SG-S156 Packing Exploded Diagram ....................................................A-10
SG-S176 Packing Exploded Diagram ....................................................A-11
SG-S216 Packing Exploded Diagram ....................................................A-12
Appendix B Technical Summary ................................................B-1
BE-0996 Block Diagram ...........................................................................B-2
Interrupt Map ............................................................................................B-3
I/O MAP ..................................................................................................B-19
Memory Map...........................................................................................B-21
Configuring WatchDog Timer .................................................................B-24
Flash BIOS Update.................................................................................B-26

v
Revision History
The revision history of SG-S156 / SG-S176 / SG-S216 User Manual is
described below:
Version No.
Revision History
Date
M2
Added user manual information for SG-S176 and
SG-S216.
2020/01/13
M1
Initial Release
2019/07/01

SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 1-1
1 Introduction
This chapter provides the introduction for SG-S156 /
SG-S176 / SG-S216 system as well as the framework of the
user manual.
The following topic is included:
•About This Manual

Chapter 1 Introduction
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 1-2
1.1 About ThisManual
Thank you for purchasing our SG-S156 / SG-S176 / SG-S216 system. The SG-S156 /
SG-S176 / SG-S216 provides faster processing speed, greater expandability and can
handle more tasks than before. This manual is designed to assist you how to install
and set up the whole system. It contains 5chapters and 2appendixes. Users can
configure the system according to their own needs. This user manual is intended for
service personnel with strong hardware background. It is not intended for general
users.
The following section outlines the structure of this user manual.
Chapter 1 Introduction
This chapter provides the introduction for the SG-S156 /SG-S176 / SG-S216 system
as well as the framework ofthe user manual.
Chapter 2 Getting Started
This chapter describes the package contents and outlines the system specifications.
Read the safety reminders carefully on how totake care of your system properly.
Chapter 3 System Configuration
This chapter describes the external I/O ports, outlines thelocations of the
motherboard components and their respective functions.You will learn how to set the
jumpers and configure the system tomeet your own needs.
Chapter 4 Software Utilities
This chapter contains helpful information for proper installations ofthe Intel Chipset
Software Installation Utility,Intel®Management Engine Components Driver
Installer, Graphics Driver Utility,LAN Driver Utility, Sound Driver Utility and
Intel®Serial I/O Driver Utility.
Chapter 5 AMI BIOS Setup
This chapter indicates you how tochange the BIOS configurations.
Appendix A System Diagrams
This appendix provides exploded diagrams and part numbers of SG-S156 /SG-S176 /
SG-S216 system.
Appendix B Technical Summary
This appendix provides the information about the allocation maps for thesystem
resources, Watchdog Timer Configuration and Flash BIOS Update.

SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-1
2 Getting Started
This chapter provides the information for the SG-S156 /
SG-S176 / SG-S216 system. It describes the package
contents and outlines the system specifications.
The following topics are included:
•Package List
•System Overview
•System Diagrams
•System Specification
•Safety Precautions
Experienced users can go to Chapter 3 System
Configuration on page 3-1 for a quick start.

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-2
2.1 Packing List
If you discover any of the items listed above are damaged or lost,
please contact your local distributor immediately.
Item
Q’ty
SG-S156 / SG-S176 / SG-S216
1
Quick Reference Guide
1
Manual / Driver DVD
1
M12 Power Supply Cable
1
U Stand (optional)
1

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-3
2.2 System Overview
Unit: mm
Front View Rear View
Top View Bottom View
Left Side View Right Side View
420
335
Antenna
Hole
Antenna
Hole
70
30
385
100
160
130.5
100
207 50

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-4
Quarter View

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-5
Unit: mm
SG-S176
Front View Rear View
Top View Bottom View
Left Side View Right Side View
381
450
17.5
153.5
175
415
73
207
100
100
M4 screw
(Depth: 8mm)
Antenna
Hole
Antenna
Hole
30
40
70

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-6
Quarter View

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-7
Unit: mm
SG-S216
Front View
Rear View
Top View
590
395
Antenna
Hole
Antenna
Hole
160.5
100
267 50
20 550
M4 screw
(Depth: 8mm)
100
245

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-8
Bottom View
Left Side View Right Side View
40
30
70
Quarter View

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-9
2.3 SG-S156 / SG-S176 / SG-S216 System Specifications
System
CPU
Type
Intel®7th Gen. CoreTM i5-7300U Processor

Intel
®
Pentium 4415U Processor
Memory
Support 1 x DDR4 2133MHz SO-DIMM socket (up to 16GB)
(non-ECC)
Operating System
Windows®10 IoT LTSC 2019

Ubuntu 16.04
Enclosure

Stainless SUS304/SUS316
IP Rating
IP66/IP69K
Power Supply

DC In 12V/24V
Mounting Support

Wall Mount / VESA 100 / Table Stand
Watchdog

1~255 second Watchdog timer selectable
BIOS

AMI SPI BIOS
Net Weight
SG-S156: 7.5kg
SG-S176: 8.5kg

SG-S216: 9.5kg
Dimensions (W x H x D)
SG-S156: 420 x 335 x 70mm
SG-S176: 450 x 381 x 70mm

SG-S216: 590 x 395 x 70mm
Certifications

FCC / CE
I/O Ports
Powe
r Input
1 x M12 Waterproof Connector with Remote Switch

Supports 12V, 24V DC
Serial Port
1 x COM port with M12 waterproof connector

COM1 for RS-232/422/485 selectable under BIOS
LAN

2 x GbE LANs with M12 waterproof connectors
LAN 1: Intel®I210IT
LAN 2: Intel®I210IT

Supports Wake-On-LAN
USB

2 x USB 2.0 M12 waterproof connectors
Storage

1 x 2.5” SATA III HDD or SSD
Expansion Slot
1 x full-sized Mini PCIe slot (Mini PCIe and USB signals)

Chapter 2 Getting Started
SG-S156/SG-S176/SG-S216 USER MANUAL
Page: 2-10
Display
LCD
SG-S156: 15” TFT LCD (LED) XGA (1024 x 768),
450 nits
SG-S176: 17” TFT LCD (LED) XGA (1280 x 1024),
350 nits
SG-S216: 21.5” TFT LCD (LED) FHD (1920 x 1080),
350 nits
Touchscreen Projected capacitive or 5-wire resistive touchscreen
(USB interface)
Environment
Operating Temperature
(with airflow)
HDD: 0°C ~ 40°C (32°F ~ 104°F)
SSD: 0°C ~ 50°C (32°F ~ 122°F)
Storage Temperature -20°C ~ 80°C (-4°F ~ 176°F)
Humidity 20%~ 90%