Vipa 605-1bl0 User manual

Manual

VIPA HMI

Touch Panel

605-1BL00

Order no.: VIPA HB160E_TP

Reference: RE_605-1BL00

Rev. 08/13

This manual is part of the documentation package with order number:

VIPA HB160E_TP and relevant for:

Product Order number as of state:

HW OS

TP 605LQS VIPA 605-1BL00 01 Windows®CE V. 5.0

Lerrzeichen

Manual VIPA HMI

Subject to change to cater for technical progress.

The information in this manual is supplied without warranties. Information is

subject to change without notice.

automatisierung mbH

Ohmstraße 4, D-91074 Herzogenaurach,

Tel.: +49 (91 32) 744 -0

Fax.: +49 (91 32) 744-144

Email: inf[email protected]

http://www.vipa.de

Hotline: +49 (91 32) 744-114

The content of this manual was carefully examined to ensure that it

conforms with the described hardware and software.

However, discrepancies can not be avoided. The specifications in this

manual are examined regularly and corrections will be included in

subsequent editions.

We gratefully accept suggestions for improvement.

VIPAis a registered trademark of VIPA Gesellschaft

für Visualisierung und Prozessautomatisierung mbH.

Microsoft, Windows and Windows Logo are either registered trademarks or

trademarks of Microsoft Cooperation in the USA and/or other countries.

Any other trademarks referred to in the text are the trademarks of the

respective owner and we acknowledge their registration.

Disclaimer of

liability

Trademarks

About this manual Manual VIPA HMI

Subject to change to cater for technical progress.

About this Manual

The manual describes the Touch Panel TP 605LQS from VIPA. Here you

find detailed descriptions of the Touch Panel beside a product overview.

Here you get information about structure, project engineering and

operation of the Touch panels from VIPA.

Chapter 1: Hardware description

During this chapter you get hints for deployment of the Touch Panel

TP 605LQS from VIPA.

Besides of a description of the single components of the Touch Panel, you

will also find the dimensions that are required for the installation. The

chapter closes with the technical data.

Chapter 2: Deployment Touch Panel

This chapter deals with the employment of the Touch Panel.

At the start of the chapter you receive information about the assembly and

the connection of the Touch Panel. The main part of the chapter introduces

Windows®CE and the various communication options offered by the Touch

Panel.

Chapter 3: Installation guidelines

This chapter helps you to install an interference-free automation system.

First, possible interference sources and their interaction mechanisms are

shown, followed by basic rules for guaranteeing EMC. Afterwards you'll find

information about assembly and cabling following EMC rules.

Overview

Manual VIPA HMI Contents

HB160E - TP - RE_605-1BL00 - Rev. 08/13 i

Contents

User considerations.................................................................................1

Safety information....................................................................................2

Chapter 1 Hardware description .....................................................1-1

Safety information for Users.................................................................1-2

Properties.............................................................................................1-3

Structure ..............................................................................................1-4

Components.........................................................................................1-6

Dimensions ..........................................................................................1-8

Technical Data.....................................................................................1-9

Chapter 2 Deployment Touch Panel ...............................................2-1

Installation............................................................................................2-2

Commissioning.....................................................................................2-4

Connection to a PLC system................................................................2-6

Operating system Windows®CE..........................................................2-7

Communication via ActiveSync ..........................................................2-13

Integrated Server ...............................................................................2-15

Access to the network resources........................................................2-22

Integration to WLAN network .............................................................2-24

Firmware update ................................................................................2-26

Chapter 3 Installation Guidelines....................................................3-1

Basic rules for the EMC-equitable assembly of installations.................3-2

EMC-equitable assembly......................................................................3-6

EMC-equitable cabling .........................................................................3-7

Special precautions providing high noise immunity ............................3-11

Checklist for the EMC-compliant installation of controllers.................3-12

Appendix ..........................................................................................A-1

Index....................................................................................................A-1

Contents Manual VIPA HMI

ii HB160E - TP - RE_605-1BL00 - Rev. 08/13

Manual VIPA HMI User considerations

HB160E - TP - RE_605-1BL00 - Rev. 08/13 1

User considerations

This manual describes the Touch Panels from VIPA. The manual consists

of chapters. Every chapter provides the description of one specific topic.

It describes the installation, project engineering, usage and the technical

data.

This Documentation is targeted at users who have a background in

automation technology and profound knowledge about Windows®operating

systems.

This manual provides the following guides:

• An overall table of contents at the beginning of the manual

• An overview of the topics for every chapter

• An index at the end of the manual.

The manual is available in:

• printed form, on paper

• in electronic form as PDF-file (Adobe Acrobat Reader)

[Button] Buttons are put in brackets e.g. [NEXT] or [OK].

[Key] Key entry are put in brackets e.g. [STRG]+[A].

Display

output Display outputs are illustrated as Courier e.g.

\flashdisk>

Keyboard

entry Keyboard entries are illustrated as Courier bold e.g.

\flashdisk> Dir

Terms Menues, Display elements, terms are italicised.

Important passages in the text are highlighted by following icons and

headings:

Danger!

Immediate or likely danger.

Personal injury is possible.

Attention!

Damages to property is likely if these warnings are not heeded.

Note!

Supplementary information and useful tips.

Objective and

contents

Guide to the

document

Availability

Description

conventions

Icons

Headings

Safety information Manual VIPA HMI

2 HB160E - TP - RE_605-1BL00 - Rev. 08/13

Safety information

The Operation devices are constructed and manufactured for:

• VIPA CPUs 11x, 21x, 31x, 51x and S7-300/400 from Siemens

• communication and process control

• industrial applications

• operation within the environmental conditions specified in the technical

data

Danger!

This device is not certified for applications in

• explosive environments (EX-zone)

The manual must be available to all personnel in the

• project design department

• installation department

• commissioning

• operation

The following conditions must be met before using or commissioning

the components described in this manual:

• Modification to the process control system should only be carried out

when the system has been disconnected from power!

• Installation and modifications only by properly trained personnel

• The national rules and regulations of the respective country must be

satisfied (installation, safety, EMC ...)

National rules and regulations apply to the disposal of the unit!

Application

specifications

Documentation

Disposal

Manual VIPA HMI Chapter 1 Hardware description

HB160E - TP - RE_605-1BL00 - Rev. 08/13 1-1

Chapter 1 Hardware description

During this chapter you get hints for deployment of the Touch Panel

TP 605LQS from VIPA.

Besides of a description of the single components of the Touch Panel, you

will also find the dimensions that are required for the installation. The

chapter closes with the technical data.

Topic Page

Chapter 1 Hardware description .....................................................1-1

Safety information for Users.................................................................1-2

Properties.............................................................................................1-3

Structure ..............................................................................................1-4

Components.........................................................................................1-6

Dimensions ..........................................................................................1-8

Technical Data.....................................................................................1-9

Overview

Content

Chapter 1 Hardware description Manual VIPA HMI

1-2 HB160E - TP - RE_605-1BL00 - Rev. 08/13

Safety information for Users

VIPA modules make use of highly integrated components in MOS-

technology. These components are extremely sensitive to over-voltages

that can occur during electrostatic discharges.

The following symbol is attached to modules that can be destroyed by

electrostatic discharges:

The symbol is located on the module, the module rack or on packing

material and it indicates the presence of electrostatic sensitive equipment.

It is possible that electrostatic sensitive equipment is destroyed by energies

and voltages that are far less than the human threshold of perception.

These voltages can occur where persons do not discharge themselves

before handling electrostatic sensitive modules and they can damage

components thereby, causing the module to become inoperable or

unusable. Modules that have been damaged by electrostatic discharges

may fail after a temperature change, mechanical shock or changes in the

electrical load.

Only the consequent implementation of protection devices and meticulous

attention to the applicable rules and regulations for handling the respective

equipment can prevent failures of electrostatic sensitive modules.

Modules have to be shipped in the original packing material.

When you are conducting measurements on electrostatic sensitive

modules you should take the following precautions:

• Floating instruments must be discharged before use.

• Instruments must be grounded.

Modifying electrostatic sensitive modules you should only use soldering

irons with grounded tips.

Attention!

Personnel and instruments should be grounded when working on

electrostatic sensitive modules.

Handling of

electrostatic

sensitive modules

Shipping of

electrostatic

sensitive modules

Measurements

and alterations on

electrostatic

sensitive modules

Manual VIPA HMI Chapter 1 Hardware description

HB160E - TP - RE_605-1BL00 - Rev. 08/13 1-3

Properties

The Touch Panel allows you to visualize and alter operating states and

recent process values of a connected PLC.

The VIPA Touch Panel is a compact and modular embedded PC based on

Windows®CE. Besides of the extensive Windows®CE functions the Touch

Panel offers varied communication possibilities. Here the Touch Panel can

simply be configured, controlled and remoted. By including a selectable

HMI/SCADA runtime the Touch Panel is particularly suitable for monitoring

and controlling of process cycles.

• Microsoft Windows®CE V. 5.0 (full version as option)

• different HMI/SCADA-Runtime selectable

• about 6MByte memory for user data on Board

• CF-Card II and MMC/SD card slot

• horizontal and vertical display selectable in 90° steps

• MPI, Profibus DP slave, USB-B interfaces on board

• robust aluminium die casting case

• display resolution up to 240 x 320 / 320 x 240 (16 levels)

• battery backed clock

• resistive touch screen

• easy mounting via integrated pivoted lever

• protection class IP65 (frontal)

Type Order number Description

TP 605LQS VIPA 605-1BL00 5.7" QVGA, LCD monochrome, MPI/Profibus DP/RS485,

USB-B

General

TP 605LQS

605-1BL00

Order data

Chapter 1 Hardware description Manual VIPA HMI

1-4 HB160E - TP - RE_605-1BL00 - Rev. 08/13

Structure

[1] Slot for storage medium

(CF, SD/MMC)

[2] Connection for interfaces and

power supply

Touch Panel

[3] Display with touch sensitive area

(touch screen)

[1] Compact Flash

[2] MMC / SD

Note!

Please regard that the Touch Panel always has to be supplied with external

voltage!

Front view

Side view

Manual VIPA HMI Chapter 1 Hardware description

HB160E - TP - RE_605-1BL00 - Rev. 08/13 1-5

123

[1] MPI/Profibus DP/RS485 interface

[2] "Slave"-USB-B interface

[3] Slot for DC 24V voltage supply

[4] Slot for CF/SD/MMC storage medium

Bottom view

(Interfaces)

TP 605LQS 5.7''

605-1BL00

Components

Chapter 1 Hardware description Manual VIPA HMI

1-6 HB160E - TP - RE_605-1BL00 - Rev. 08/13

Components

The following memory systems are available for every Touch Panel:

• 64MByte work memory

• 32MByte Flash-Disk (6MByte for user data)

• Slot for CF (Type II)

• Slot for MMC/SD

Every Touch Panel has a work memory with a size of 64MByte. The work

memory is not buffered and is deleted after shut down. Please regard that

also registry entries are stored in the work memory that are set back to

default settings after the next re-boot. You may save them permanently by

means of the KuK Tools (within consignment).

As internal permanent storage medium every Touch Panel has a flash disc

with a size of 32MByte (6MByte user data). After the start of Windows®CE

this memory is listed as Flashdisk at My Device.

Slot for CF

Here you may plug a CompactFlashtype II. The card may be plugged and

removed during runtime and is immediately listed as Storage Card at My

Device.

Every CompactFlashstorage module has a pulling edge. Hold the

CompactFlash in the way that the pulling edge points to the left side. Push

the storage module without much power into the slot until the impact. To

remove the card touch it at the pulling edge and pull.

At this slot you may plug storage modules of the type SD or MMC. The

card may be plugged and removed during runtime and is immediately listed

as SDMMC Card at My Device.

Please take care to plug the according card as shown at the backside of

the Touch Panel.

Security flap for

memory cards

At the left side of the Touch Panel are the card slots for memory cards. The

cards are visibly covered by a security flap and are thus secured from

slipping out.

Please take care to pull the security flap back before plugging or pulling a

memory card like shown in the illustration and put it back again afterwards.

When plugging, the security flap additionally snaps into position above the

plugged memory card.

Memory

management

Work memory

Flash disc

Slot for SD/MMC

Manual VIPA HMI Chapter 1 Hardware description

HB160E - TP - RE_605-1BL00 - Rev. 08/13 1-7

9pin jack Connection RS485

Pin RS485

1 n.c.

2 M24V

3 RxD/TxD-P (Line B)

4 RTS

5 M5V

6 P5V

7 P24V

8 RxD/TxD-N (Line A)

9 n.c.

RxD/TxD-P(B)

Shield

RS485

P24V

RxD/TxD-P(B)

RxD/TxD-N(A)

Periphery

P5V

M5V

RTS 4

Shield

For project transfer with Microsoft ActiveSync a programming cable can be

connected using the "Slave"-USB-B interface.

The pin assignment is as follows:

"Slave"-USB-B:

Pin Assignment

1 VCC

2 DM

3 DP

34 4 GND

The USB-A interface of your PC can be connected to the "Slave"-USB-B

interface of your Touch Panel deploying the USB programming cable.

The USB programming cable is delivered by VIPA with order No.

VIPA 670-0KB10.

The Touch Panel has got an integrated power supply. The power supply

has to be provided with DC 24V (20.4 ... 28.8V). For this you find an

according DC 24V slot at the bottom side.

DC 24V

The power supply is protected against inverse polarity and overcurrent.

Profibus DP /

MPI interface

(RS485)

"Slave"-USB-B

VIPA USB-B

Programming cable

Power supply

Chapter 1 Hardware description Manual VIPA HMI

1-8 HB160E - TP - RE_605-1BL00 - Rev. 08/13

Dimensions

installation width

installation hight

installation

depth

width

height

For the installation of the Touch Panel in control cabinets and desks the

following dimensions are necessary:

Installation cutting (W x H) 200 x 144mm

Front panel (W x H) 212 x 156mm

Installation depth 37mm

Note!

The degrees of protection are only guaranteed when the following is

observed:

• Material thickness at the mounting cut-out: 2 ... 5mm

• the deviation from the plane for the panel cut-out is ≤0.5mm. This

condition must be fulfilled for the mounted HMI device

• Permissible surface roughness in the area of the seal: ≤120µm (friction

coefficient 120)

Installation

dimensions

5.7''

605-1BL00

Manual VIPA HMI Chapter 1 Hardware description

HB160E - TP - RE_605-1BL00 - Rev. 08/13 1-9

Technical Data

TP 605LQS

Electrical data VIPA 605-1BL00

Nominal supply voltage DC 24V (20.4 ... 28.8V)

ESD/Burst Acc. IEC 61000-4-2 / IEC 61000-4-4 (up to level 3)

Shock resistance Acc. IEC 60068-2-6 / IEC 60068-2-27 (1G/12G)

Level of noise suppression Acc. IEC 61000-6-4

mark of conformity and certification CE

Clock and housing

Processor Xscale 520MHz

Clock Hardware clock, buffered

Housing - protection class Solid aluminium case

- Front IP 65

- Back IP 20

Environment conditions

Mounting position horizontally/vertically

Operating temperature 0 ... +50°C

Relative humidity max. 85%

Storing / Transport temperature -20 to +60°C

Display

Size 5.7"

Resolution 240 x 320 / 320 x 240

Colors STN LCD monochrome (16 levels)

MTBF Backlights (25°C) ca. 75000h

Peripherals

Touch screen resistive

Memory

Type 32MB Flash / 64MB RAM

Available memory for user data ca. 6MByte

SD/MMC Push-Push-Slot yes

Interfaces

MPI (12MBits), Profibus DP RS485 isolated

USB USB-B

Electrical Data

Nominal supply voltage DC 24V (20.4 ... 28.8V)

Nominal current 0.4A

Housing

Mounting via 4 integrated pivoted lever

Dimensions and weight

Front side (WxH) 212 x 156mm

Back side (WxHxD) 198 x 142 x 37mm

Installation cutting (WxH) 200 x 144mm

Weight 1.2kg

Chapter 1 Hardware description Manual VIPA HMI

1-10 HB160E - TP - RE_605-1BL00 - Rev. 08/13

Manual VIPA HMI Chapter 2 Deployment Touch Panel

HB160E - TP - RE_605-1BL00 - Rev. 08/13 2-1

Chapter 2 Deployment Touch Panel