SEELEY INTERNATIONAL MEGACOOL MIV User manual

®
OWNER’S MANUAL
Portable Evaporative Cooler
ILL863-A
ILL863-AILL1222-A
(MIV)
(MIC)
(MI)

CONTENTS
SAFETY 1
2NOITACOLTNENOPMOC
ASSEMBLY 3-4
6-4ESUROFSNOITCERID
MAINTENANCE 6 7
TROUBLESHOOTING 8
SPARE PARTS LIST & EXPLODED VIEW 9-10
WARRANTY 11
........................................................................
General Safety
Electrical Safety
...........................................
..................................................................
Caution - Check Voltage
To assemble the cooler
..............................................
How to get the best cooling performance
Filling with water
Using the cooler - Low fan speed
High fan speed
Fan only (vent)
Conditioning of Aspen cooling pads
Air direction control
Safety instructions
Cleaning the cooler/rear panel removal
............................................................ -
To drain water
Water strainer and Aspen cooling pad
Pump belt replacement / Drain Plug
..................................................
..................
.................................................................
Waste electrical products must not be disposed of with household waste. This product
should be taken to your local recycling centre for safe treatment.
iMillenia series Portable Evaporative Cooler
®
CONTENTS
SAFETY 1
2NOITACOLTNENOPMOC
ASSEMBLY 3-4
6-4ESUROFSNOITCERID
MAINTENANCE 6 7
TROUBLESHOOTING 8
SPARE PARTS LIST & EXPLODED VIEW 9-10
WARRANTY 11
........................................................................
General Safety
Electrical Safety
...........................................
..................................................................
Caution - Check Voltage
To assemble the cooler
..............................................
How to get the best cooling performance
Filling with water
Using the cooler - Low fan speed
High fan speed
Fan only (vent)
Conditioning of Aspen cooling pads
Air direction control
Safety instructions
Cleaning the cooler/rear panel removal
............................................................ -
To drain water
Water strainer and Aspen cooling pad
Pump belt replacement / Drain Plug
..................................................
..................
.................................................................
Waste electrical products must not be disposed of with household waste. This product
should be taken to your local recycling centre for safe treatment.
iMillenia series Portable Evaporative Cooler
®

SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY
Electrical Safety
Caution! before connecting the electrical
power cord to a power outlet, check that
the air cooler voltage is the same as your
power supply (refer to the rating label
located on the rear of the unit).
Do not pull the unit along by the power
cord or place the power cord near a
source of heat. Always unroll the power
cord completely before use.
Switch off and unplug when not in use.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or qualified
persons in order to avoid a hazard.
similarly
Portable evaporative air cooler -
important safety instructions
Please read these instructions before
assembling the cooler and keep for future
reference.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Clean the air inlets and outlets at regular
intervals to prevent airflow reduction (refer
Maintenance section).
Do not store or operate the appliance near
any flammable substances.
During operation, water is present in the
bottom tank of the air cooler. Be careful when
moving the unit to prevent water from spilling.
General Safety
For indoor use only.
Use only in the upright position on a flat level
surface and at least 50cm from any objects.
Do not place objects on the air cooler, or
through the ventilating slots or restrict the air
inlets & outlets.
Closely supervise any children and pets when
the air cooler is in use.
Always switch your cooler off and unplug it
before cleaning or maintenance.
SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY
Electrical Safety
Caution! before connecting the electrical
power cord to a power outlet, check that
the air cooler voltage is the same as your
power supply (refer to the rating label
located on the rear of the unit).
Do not pull the unit along by the power
cord or place the power cord near a
source of heat. Always unroll the power
cord completely before use.
Switch off and unplug when not in use.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or qualified
persons in order to avoid a hazard.
similarly
Portable evaporative air cooler -
important safety instructions
Please read these instructions before
assembling the cooler and keep for future
reference.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Not for outdoor use. May be used when
attended in a covered patio, alfresco and
external area not directly exposed to weather.
Use only in the upright position on a flat level
surface and at least 50cm from any objects.
Clean the air inlets and outlets at regular
intervals to prevent airflow reduction (refer
Maintenance section).
Do not place objects on the air cooler, or
through the ventilating slots or restrict the air
inlets & outlets.
Closely supervise any children and pets when
the air cooler is in use.
Do not store or operate the appliance near
any flammable substances.
During operation, water is present in the
bottom tank of the air cooler. Be careful when
moving the unit to prevent water from spilling.
Always switch your cooler off and unplug it
before cleaning or maintenance.
General Safety

2Millenia series Portable Evaporative Cooler
®
COMPONENT LOCATION
KEY
A Controls
B Front grille
C Water filling door
D Water reservoir
E Castors
F Water level indicator
G Front pillar ( llenia, Megacool)
H Base
I Rear panel retaining screws (2)
J Rear panel
K Power cord entry point
L Reservoir drain plug
M Rating label
N Cord storage hooks
O Rear pillar ( llenia, Megacool)
Mi
Mi
B
D
C
EH
F
G
A
ILL864-AILL865-B
K
L
J
I
N
M
O
2Millenia series Portable Evaporative Cooler
®
COMPONENT LOCATION
KEY
A Controls
B Front grille
C Water filling door
D Water reservoir
E Castors
F Water level indicator
G Front pillar ( llenia, Megacool)
H Base
I Rear panel retaining screws (2)
J Rear panel
K Power cord entry point
L Reservoir drain plug
M Rating label
N Cord storage hooks
O Rear pillar ( llenia, Megacool)
Mi
Mi
B
D
C
EH
F
G
A
ILL864-AILL865-B
K
L
J
I
N
M
O

SEELEY INTERNATIONAL – OWNER’S MANUAL 3
8
ILL1221-A
CAUTION! - Check Voltage
Before connecting your electrical power
cord to a power outlet, check that the
cooler voltage is the same as your power
supply. The cooler voltage will be stated
on the rating label at the rear of the
cooler (Fig 6).
ASSEMBLY
ILL866-A
6
To assemble the cooler
Push the four castors into their locating
holes in the base. Use a rotating motion
to assist in the entry of the steel spring
ring ( Fig 7).
*
7
ILL867-B
*
Models llenia and Megacool only
Assemble the front and rear pillars and
screw together. Place this assembly on
the base and slide into position until it
locks (Fig 8).
Mi
Models llenia and Megacool only
Place the reservoir of the cooler onto the
front pillar as shown (Fig 9). Tilt
downwards towards the rear until the
reservoir locks onto the rear pillar.
To remove the unit from the pillars, use a
screwdriver in the two recesses in the
rear of the reservoir to release the clips.
Tilt the unit forward to remove.
Mi
ILL870-A
9
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
8
ILL1221-A
CAUTION! - Check Voltage
Before connecting your electrical power
cord to a power outlet, check that the
cooler voltage is the same as your power
supply. The cooler voltage will be stated
on the rating label at the rear of the
cooler (Fig 6).
ASSEMBLY
ILL866-A
6
To assemble the cooler
Push the four castors into their locating
holes in the base. Use a rotating motion
to assist in the entry of the steel spring
ring ( Fig 7).
*
7
ILL867-B
*
Millenia and Megacool only
Assemble the front and rear pillars and
screw together. Place this assembly on
the base and slide into position until it
locks (Fig 8).
Millenia and Megacool only
Place the reservoir of the cooler onto the
front pillar as shown (Fig 9). Tilt
downwards towards the rear until the
reservoir locks onto the rear pillar.
To remove the unit from the pillars, use a
screwdriver in the two recesses in the
rear of the reservoir to release the clips.
Tilt the unit forward to remove.
ILL870-A
9

4
®
Millenia series Portable Evaporative Cooler
Mastercool only
Place the reservoir onto the base and
press down to engage the four clips in the
base (Fig 10).
To remove the cooler from the base, tip it
upside down and release the clips in the
base.Ascrewdriver may be necessary.
How to get the best cooling
performance
Place the cooler with its back near to an
open window or door so it can draw in
100% fresh air.
Open another window or door on the
opposite side of the room for “flow
through” ventilation. This cooler will not
cool properly in a closed room (Fig 11).
ILL1219-A
10
ILL871-A
11
ILL872-A
12
Filling with water
Turn the cooler off before filling. Open the
water filling door and pour in clean water
(Fig 12).
The water capacity is 14 litres. The
nimum amount of water needed for the
pump to operate is 2 litres.
mi
The cooler is full when the water level
indicator is in the “FULL” position
(Fig 13).
! The cooler and pump will not be
damaged if operated without water.
Do not overfill, as water will
spill out of the cooler!
Note
DIRECTIONS FOR USE
FULL
EMPTY
13
ILL873-B
ASSEMBLY cont.
4
®
Millenia series Portable Evaporative Cooler
Model Mastercool only
Place the reservoir onto the base and
press down to engage the four clips in the
base (Fig 10).
To remove the cooler from the base, tip it
upside down and release the clips in the
base.Ascrewdriver may be necessary.
How to get the best cooling
performance
Place the cooler with its back near to an
open window or door so it can draw in
100% fresh air.
Open another window or door on the
opposite side of the room for “flow
through” ventilation. This cooler will not
cool properly in a closed room (Fig 11).
ILL1219-A
10
ILL871-A
11
ILL872-A
12
Filling with water
Turn the cooler off before filling. Open the
water filling door and pour in clean water
(Fig 12).
The water capacity is 14 litres. The
nimum amount of water needed for the
pump to operate is 2 litres.
mi
The cooler is full when the water level
indicator is in the “FULL” position
(Fig 13).
! The cooler and pump will not be
damaged if operated without water.
Do not overfill, as water will
spill out of the cooler!
Note
DIRECTIONS FOR USE
FULL
EMPTY
13
ILL873-B
ASSEMBLY cont.

5SEELEY INTERNATIONAL – OWNER’S MANUAL
DIRECTIONS FOR USE cont.
Using the cooler
When this appliance is used as an air cooler,
it should be filled with water and the cool
knob turned to the “COOL” position (Fig 14).
(1) is selected for quietest
operation (Fig 14).
(3) is for maximum cooling
(Fig 15).
. This cooler may be
used as a fan only. Set the cool knob to
position “0” (Fig 15).
Low fan speed
High fan speed
Fan only (ventilation)
14
ILL1433-A
15
ILL1434-A
Conditioning of the aspen cooling
pad
To get the best performance from your cooler,
we recommend that when first used it is run
with water for at least 10 nutes at the
setting in Fig 16.
During this process the water becomes
slightly yellow, and there is a natural smell of
damp wood. This is normal.
mi
Air direction control -
llenia / Mastercool
The cooler is provided with air guide vanes
which can be adjusted as required to direct
the air flow.
Millenia and Mastercool are adjusted
manually by sliding the levers on the front
panel (Fig 17).
Mi
Mi
16
ILL1435-A
ILL877-C
MILLENIA / MASTERCOOL
17
5SEELEY INTERNATIONAL – OWNER’S MANUAL
DIRECTIONS FOR USE cont.
Using the cooler
When this appliance is used as an air cooler,
it should be filled with water and the cool
knob turned to the “COOL” position (Fig 14).
(1) is selected for quietest
operation (Fig 14).
(3) is for maximum cooling
(Fig 15).
. This cooler may be
used as a fan only. Set the cool knob to
position “0” (Fig 15).
Low fan speed
High fan speed
Fan only (ventilation)
14
ILL1433-A
15
ILL1434-A
Conditioning of the aspen cooling
pad
To get the best performance from your cooler,
we recommend that when first used it is run
with water for at least 10 nutes at the
setting in Fig 16.
During this process the water becomes
slightly yellow, and there is a natural smell of
damp wood. This is normal.
mi
Air direction control -
llenia / Mastercool
The cooler is provided with air guide vanes
which can be adjusted as required to direct
the air flow.
Millenia and Mastercool are adjusted
manually by sliding the levers on the front
panel (Fig 17).
Mi
16
ILL1435-A
ILL877-C
MILLENIA / MASTERCOOL
17

6
®
Millenia series Portable Evaporative Cooler
Air direction control Megacool
Megacool has motor driven vanes
that are switched on and off by the fan
control switch on the control panel (Fig
18). Set the control to the “sweep / fan”
speed setting to operate the sweep vanes
(shown). Set to “fan” speed settings for
fixed direction.
There are no manual adjustment levers.
Cleaning the cooler
Important! Always switch off and
remove the electrical plug before
cleaning and servicing the
cooler.
To clean, wipe the cooler with a damp
cloth and a little household detergent.
The rear panel can be removed to gain
access to inside the cooler by removing
the screws at the top of each side.
Pivot the panel backwards and lift off
(Fig 20). ILL880-B
20
Safety instruction
As this cooler contains water, ensure it is
moved carefully and is not tilted, as water
may spill (Fig 19).
ILL878-B
19
18
ILL1436-A
MAINTENANCE
DIRECTIONS FOR USE cont.
6
®
Millenia series Portable Evaporative Cooler
Air direction control Megacool
Model Megacool has motor driven vanes
that are switched on and off by the fan
control switch on the control panel (Fig
18). Set the control to the “sweep / fan”
speed setting to operate the sweep vanes
(shown). Set to “fan” speed settings for
fixed direction.
There are no manual adjustment levers.
Cleaning the cooler
Important! Always switch off and
remove the electrical plug before
cleaning and servicing the
cooler.
To clean, wipe the cooler with a damp
cloth and a little household detergent.
The rear panel can be removed to gain
access to inside the cooler by removing
the screws at the top of each side.
Pivot the panel backwards and lift off
(Fig 20). ILL880-B
20
Safety instruction
As this cooler contains water, ensure it is
moved carefully and is not tilted, as water
may spill (Fig 19).
ILL878-B
19
18
ILL1436-A
MAINTENANCE
DIRECTIONS FOR USE cont.

MAINTENANCE cont.
End of Season
At least once a year at the end of summer it
is advisable to do some simple maintenance
on your cooler to maintain its high efficiency.
This involves cleaning the water system and
the Aspen cooling pad.
To drain water
Drain the water from the cooler by moving the
cooler to a drain and removing the drain plug
located on the bottom of the tank. When the
cooler is empty replace the plug in the tank
(Fig 21).
21
A
BA
22
Pump belt replacement
If a pump drive belt needs replacing, access
can be gained by using a tool (screwdriver) to
remove the small access door (Fig 22 - “A”).
Each cooler is supplied with a spare drain
plug, located in the position shown (Fig 22 -
“B”).
Spare drain plug
Water strainer and aspen cooling pad
Clean the water strainer by removing any
foreign matter. Wash the Aspen cooling pad
with water while it is still in the rear panel.
Replace the pad if it is worn or deteriorated.
7SEELEY INTERNATIONAL – OWNER’S MANUAL
ILL879-A
ILL882-B
MAINTENANCE cont.
End of Season
At least once a year at the end of summer it
is advisable to do some simple maintenance
on your cooler to maintain its high efficiency.
This involves cleaning the water system and
the Aspen cooling pad.
To drain water
Drain the water from the cooler by moving the
cooler to a drain and removing the drain plug
located on the bottom of the tank. When the
cooler is empty replace the plug in the tank
(Fig 21).
21
A
BA
22
Pump belt replacement
If a pump drive belt needs replacing, access
can be gained by using a tool (screwdriver) to
remove the small access door (Fig 22 - “A”).
Each cooler is supplied with a spare drain
plug, located in the position shown (Fig 22 -
“B”).
Spare drain plug
Water strainer and aspen cooling pad
Clean the water strainer by removing any
foreign matter. Wash the Aspen cooling pad
with water while it is still in the rear panel.
Replace the pad if it is worn or deteriorated.
7SEELEY INTERNATIONAL – OWNER’S MANUAL
ILL879-A
ILL882-B

8
®
Millenia series Portable Evaporative Cooler
3.6 Fan/pump not running
fast enough on low speed.
3.7 Pump drive belt faulty
or broken.
3.6.1 Check that supply voltage is up to correct level.
3.6.2 Fan and pump will pick up speed slightly as the motor
reaches normal operating temperature. Allow the cooler to
run for 30-60 nutes and check again.
3.7.1 Replace drive belt as shown on page 7.
mi
4.1 Reservoir or Aspen
cooling pad dirty.
4.2 Water quality is poor.
4.1.1 Drain reservoir and fill the cooler with clean water. If it
still smells clean the reservoir and replace the Aspen cooling
pad or proceed to 4.2.1.
4.2.1 Add a little vanilla essence or perfume to the water.
4. Cooler makes bad
smell.
5.1 Dirt has accumulated
inside pump.
5.1.1 Proceed as in 3.5.1
5.1.2 Replace drive belt as shown on page 7.
5. Cooler makes
scraping or rattling
noise on new season
start up.
6.1 Too much water in
reservoir.
6.2 Water level indicator
not working.
6.1.1 Drain some water out (see page 7).
6.2.1 Remove the rear panel for access. Slide the indicator
up to the 'FULL' position then let it drop.
6. Water overflows from
reservoir.
7.1.1 If the power supply cord of this appliance is damaged it
must be replaced. Electrical parts must only be replaced by
qualified electrical contractors.
7. Damaged power
supply cord.
3. No cooling. 3.1 Cooling control is off.
3.2 Reservoir is empty or
nearly empty.
3.3 Weather is too hu d.
3.4 Aspen cooling pad and
/ or pump inlet screen
blocked or dirty.
3.5 Pump is not working
properly.
mi
3.1.1 Turn cool knob to 'COOL'.
3.2.1 Fill with water again until water level indicator is at the
'FULL' position. Water capacity is 14 litres
3.3.1 Turn cool knob to '0' and use cooler as a fan only.
3.4.1 Clean parts - see maintenance page 6.
3.5.1 The pump is NOT a separate electric pump. It is
connected to the fan motor and is driven mechanically. Turn
the cooler off and completely drain the reservoir. Refill with
water. Switch fan knob to high speed (3), turn the cool knob
to 'COOL',run the cooler for 10-15 nutes non-stop. This will
help dissolve and flush out the dirt. The Aspen cooling pad
should now be wet.
mi
1. Cooler will not
operate.
2. Cooler stops
operating after running
for some time and does
not restart.
1.1 Power outlet or supply
faulty.
1.2 Wrong voltage.
2.1 Motor in safety
shutdown.
1.1.1 Switch on power outlet.
1.1.2 Check power supply.
1.1.3 Check power outlet.
1.2.1 Check that power supply is the same as specified on
the rating label.
2.1.1 Cooler will need to be returned under warranty.
TROUBLESHOOTING
CONDITION POSSIBLE CAUSE REMEDY
8
®
Millenia series Portable Evaporative Cooler
3.6 Fan/pump not running
fast enough on low speed.
3.7 Pump drive belt faulty
or broken.
3.6.1 Check that supply voltage is up to correct level.
3.6.2 Fan and pump will pick up speed slightly as the motor
reaches normal operating temperature. Allow the cooler to
run for 30-60 nutes and check again. If there is no
improvement have the cooler checked by a service agent.
3.7.1 Replace drive belt as shown on page 7.
mi
4.1 Reservoir or Aspen
cooling pad dirty.
4.2 Water quality is poor.
4.1.1 Drain reservoir and fill the cooler with clean water. If it
still smells clean the reservoir and replace the Aspen cooling
pad or proceed to 4.2.1.
4.2.1 Add a little vanilla essence or perfume to the water.
4. Cooler makes bad
smell.
5.1 Dirt has accumulated
inside pump.
5.1.1 Proceed as in 3.5.1
5.1.2 Replace drive belt as shown on page 7.
5. Cooler makes
scraping or rattling
noise on new season
start up.
6.1 Too much water in
reservoir.
6.2 Water level indicator
not working.
6.1.1 Drain some water out (see page 7).
6.2.1 Remove the rear panel for access. Slide the indicator
up to the 'FULL' position then let it drop. If it fails to operate
have it checked by a service agent.
6. Water overflows from
reservoir.
7.1 Electrical fault. 7.1.1 Electrical parts must only be repaired and replaced by
Authorised Service Agents.
7. Cooler will not
operate at all.
8.1.1 If the power supply cord of this appliance is damaged it
must be replaced. Electrical parts must only be repaired and
replaced by Authorised Service Agents.
8. Damaged power
supply cord.
3. No cooling. 3.1 Cooling control is off.
3.2 Reservoir is empty or
nearly empty.
3.3 Weather is too hu d.
3.4 Aspen cooling pad and
/ or pump inlet screen
blocked or dirty.
3.5 Pump is not working
properly.
mi
3.1.1 Turn cool knob to 'COOL'.
3.2.1 Fill with water again until water level indicator is at the
'FULL' position. Water capacity is 14 litres
3.3.1 Turn cool knob to '0' and use cooler as a fan only.
3.4.1 Clean parts - see maintenance page 6.
3.5.1 The pump is NOT a separate electric pump. It is
connected to the fan motor and is driven mechanically. Turn
the cooler off and completely drain the reservoir. Refill with
water. Switch fan knob to high speed (3), turn the cool knob
to 'COOL',run the cooler for 10-15 nutes non-stop. This will
help dissolve and flush out the dirt. The Aspen cooling pad
should now be wet. If the pad is not visibly wet and there is
no cooling, have the cooler checked by a service agent.
mi
1. Cooler will not
operate at first.
2. Cooler stops
operating after running
for some time and does
not restart.
1.1 Power outlet or supply
faulty.
1.2 Wrong voltage.
2.1 Motor in safety
shutdown.
1.1.1 Switch on power outlet.
1.1.2 Check power supply.
1.1.3 Check power outlet.
1.2.1 Check that power supply is the same as specified on
the rating label.
2.1.1 Motor must be replaced by Authorised Service Agent.
TROUBLESHOOTING
CONDITION POSSIBLE CAUSE REMEDY
Email [email protected] for more information.

9SEELEY INTERNATIONAL – OWNER’S MANUAL
When ordering spare parts, please specify the model / serial number
and colour of your cooler.
SPARE PARTS LIST
noitpircseDmetI
)gulpniardsedulcni(knaT1
gulPniarD2
lenaPraeR3
daPretliF4
ylbmessAellirGtnorF5
ellirGtnorF-egdaB6
wodniW7
rooDrelliF8
9iM ylbmessAlenaPd
ylbmessAredaerpS/ellirGrennI01
rooDellirGrennI11
swercS21
)riap(ralliPraeR/tnorF31
esaB41
tcapmoc-esaB1.41
ylbmessAeltniP&rotsaC51
lenaPlortnoC61
xoBlortnoC71
81
1.81
moorhsuMbonK
ylbmessAtfahS&moorhsuMbonK
ylbmessAevlaVre
taW91
02
1.02
loocretsaM/ainell)-6002(hctiwS iM
loocageM)-6002(hctiwS
enaVreveL22
HRkniLenaV32
HLkniLenaV42
enaV52
gniraeBenaV62
rotoMkniLenaV72
)loocageM/ainell( iM
)ylnoloocageM/ainell( iM
)ylnoloocretsaM(
noitpircseDmetI
pmalCdaP82
rotacidnIleveLretaW92
ylbmessAtaolF03
ylbmessApmuP13
reniartS23
rotoMenaV33
buHrotoMenaV43
yelluPnaF63
naF73
tleBevirD83
93 esoHredaerpS 054x5.9
14 esoHpmuP 098x5.9
24
1.24
rotoMerauqSrofetihWsrebbuRrotoM
rotoMdnuoRrofkcalBsrebbuRrotoM
1.34
34
dnuoR-zH05V032rotoMcirtcelE
erauqS-zH05V032rotoMcirtcelE
44 rotoMroffu2.3roticapaC
64 ailartsuAdroC&gulP
74 1-K4droCtalF-pirGdroC
)ylnoloocageM(
)ylnoloocageM(
9SEELEY INTERNATIONAL – OWNER’S MANUAL
When ordering spare parts, please specify the model / serial number
and colour of your cooler.
SPARE PARTS LIST
noitpircseDmetI
)gulpniardsedulcni(knaT1
gulPniarD2
lenaPraeR3
daPretliF4
ylbmessAellirGtnorF5
ellirGtnorF-egdaB6
wodniW7
rooDrelliF8
9iM ylbmessAlenaPd
ylbmessAredaerpS/ellirGrennI01
rooDellirGrennI11
swercS21
)riap(ralliPraeR/tnorF31
esaB41
tcapmoc-esaB1.41
ylbmessAeltniP&rotsaC51
lenaPlortnoC61
xoBlortnoC71
81
1.81
moorhsuMbonK
ylbmessAtfahS&moorhsuMbonK
ylbmessAevlaVretaW91
02
1.0
2
loocretsaM/ainell)-6002(hctiwS iM
loocageM)-6002(hctiwS
enaVreveL22
HRkniLenaV32
HLkniLenaV42
enaV52
gniraeBenaV62
rotoMkniLenaV72
)loocageM/ainell( iM
)ylnoloocageM/ainell( iM
)ylnoloocretsaM(
noitpircseDmetI
pmalCdaP82
rotacidnIleveLretaW92
ylbmessAtaolF03
ylbmessApmuP13
reniartS23
rotoMenaV33
buHrotoMenaV43
yelluPnaF63
naF73
tleBevirD83
93 esoHredaerpS 054x5.9
14 esoHpmuP 098x5.9
24
1.24
rotoMerauqSrofetihWsrebbuRrotoM
rotoMdnuoRrofkcalBsrebbuRrotoM
1.34
34
dnuoR-zH05V032rotoMcirtcelE
erauqS-zH05V032rotoMcirtcelE
44 rotoMroffu2.3roticapaC
64 ailartsuAdroC&gulP
74 1-K4droCtalF-pirGdroC
)ylnoloocageM(
)ylnoloocageM(

10
®
Millenia series Portable Evaporative Cooler
As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
927 03 21
5425262 14 93 91
1.81
81 0261 44 71 2434 63 43
01
11
83
923 7313
41
31
51
32
72 33 43
64 74
21
82
ainelliM
loocageM loocretsaM
8
622 21
ILL1432-A 0609
EXPLODED VIEW
10
®
Millenia series Portable Evaporative Cooler
As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
927 03 21
5425262 14 93 91
1.81
81 0261 44 71 2434 63 43
01
11
83
923 7313
41
31
51
32
72 33 43
64 74
21
82
ainelliM
loocageM loocretsaM
8
622 21
ILL1432-A 0609
EXPLODED VIEW

11SEELEY INTERNATIONAL – OWNER’S MANUAL
WARRANTY
In this warranty:
or us means Seeley International Pty Ltd ABN 23 054 687 035, and our contact details are
set out at the end of this warranty;
means you, the original end-user purchaser of the Goods;
means the authorised distributor or retailer of the Goods that sold you the Goods in
Australia; and
means the product, unit, appliance or equipment which was accompanied by this
warranty and purchased in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired
or replaced if the Goods fail to be of acceptable quality and the failure does not amount to a
major failure.
In addition to any rights and remedies that You may have under the Australian Consumer Law or
any other law, subject to the terms of this warranty, We provide the following warranty:
1. If, during the first 24 months from the date of first retail purchase ( ), the
Goods upon examination prove defective by reason of improper workmanship or material,
We will repair at our nearest service centre or replace (at our option), the product or any part
thereof without charge. Should we deem in our absolute discretion to replace the Goods, we
may substitute any similar good even if it is not on our current price/equipment list. Further,
Goods presented for repair may be replaced by refurbished goods of the same type rather
than being repaired. Refurbished parts may be used to repair the Goods.
2. We are under no obligation to repair or replace the Goods under clause1if the Goods have
not been used only for personal, domestic or household purposes or have not been
operated and maintained in accordance with the instructions in the Owner's Manual. The
addition of any third party device or the removal or the alteration of any of our components
will void this warranty. In addition, the warranty granted under clause1does not apply to:
• Consumable components such as filters,
• Adjustments necessary due to misuse of the cooler,
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user misuse, tampering, or failure to observe the care and
special provisions in the instructions.
3. The warranty granted under clause1is limited to repair or replacement only. As far as the
law permits, We will not be liable for any consequential loss suffered through, or resulting
from, the non operation, or ineffective operation of the Goods. The warranty granted under
clause1does not cover damage to the Goods or other loss resulting from acts of God.
4. We are not responsible in any way for any failure and/or inadequate performance of the
Goods which arises from or is connected to the use in the Goods of non-genuine spare
parts. We strongly recommend that only spare parts supplied or approved by us are used in
the Goods.
We
You
Supplier
Goods
Warranty Period
11SEELEY INTERNATIONAL – OWNER’S MANUAL
WARRANTY
In this warranty:
We or us means Seeley International Pty Ltd ABN 23 054 687 035, and our contact details are
set out at the end of this warranty;
You means you, the original end-user purchaser of the Goods; and
Goods means the product, unit, appliance or equipment which was accompanied by this
warranty and purchased from us in Australia for use in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired
or replaced if the Goods fail to be of acceptable quality and the failure does not amount to a
major failure.
In addition to any rights and remedies that You may have under the Australian Consumer Law or
any other law, subject to the terms of this warranty, We provide the following warranty:
1. If, during the first 24 months from the date of first retail purchase (Warranty Period), the
Goods upon examination prove defective by reason of improper workmanship or material,
We will repair at our nearest service centre or replace (at our option), the product or any part
thereof without charge. Should we deem in our absolute discretion to replace the Goods, we
may substitute any similar good even if it is not on our current price/equipment list. Further,
Goods presented for repair may be replaced by refurbished goods of the same type rather
than being repaired. Refurbished parts may be used to repair the Goods.
2. We are under no obligation to repair or replace the Goods under clause 1 if the Goods have
not been used only for personal, domestic or household purposes, or have not been
operated and maintained in accordance with the instructions in the Owner's Manual, or have
been used outside Australia. The addition of any third party device or the removal or the
alteration of any of our components will void this warranty. In addition, the warranty granted
under clause 1 does not apply to:
• Consumable components such as filters,
• Adjustments necessary due to misuse of the cooler,
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user misuse, tampering, or failure to observe the care and
special provisions in the instructions.
3. The warranty granted under clause 1 is limited to repair or replacement only. As far as the
law permits, We will not be liable for any consequential loss suffered through, or resulting
from, the non operation, or ineffective operation of the Goods. The warranty granted under
clause 1 does not cover damage to the Goods or other loss resulting from acts of God.
4. We are not responsible in any way for any failure and/or inadequate performance of the
Goods which arises from or is connected to the use in the Goods of non-genuine spare
parts. We strongly recommend that only spare parts supplied or approved by us are used in
the Goods.
112 O'Sullivan Beach Road, Lonsdale, South Australia, 5160
Customer service centre in Australia: 1300 650 644
Website: www.seeleyinternational.com
112 O'Sullivan Beach Road, Lonsdale, South Australia, 5160
Customer service centre in Australia: 1300 650 644
Website: www.seeleyinternational.com

WARRANTY cont.
12
®
Millenia series Portable Evaporative Cooler
WARRANTY cont.
12
®
Millenia series Portable Evaporative Cooler
5. No other person, firm or corporation is authorised by us to offer or give on our behalf any
other or greater warranty than that given under this warranty. The benefits conferred by this
warranty are in favour of You and any person deriving title to the Goods through or under
such person and are intended to be separate from and additional to all other rights and
remedies that they may have in law in respect of the Goods.
6. In order to claim under the warranty granted under clause1you must:
(a) either:
(i) contact us within the Warranty Period on: ;
or
(ii) logaclaim on our website www.seeleyinternational.com within the Warranty Period;
and
(b) return the Goods to your nearest service centre (or to us at the address below) by
prepaid freight within the Warranty Period, together with (i) the legible and unmodified
proof of purchase, which clearly indicates the name and address of the original retailer,
the date and place of purchase, the product name or other product serial number, and
(ii)acopy of the completed Warranty Information page below. (If you choose to return
the Goods to us, there is an additional requirement - they will also need to be
accompanied byacovering letter which states your name and address and daytime
telephone number, and the model and serial number of the goods.)
7. This warranty does not cover the cost of claiming under the warranty, it is your responsibility
to cover all forwarding and return freight costs incurred in sending the Goods to and from
your nearest service centre or us.
8. This warranty is only valid and enforceable in Australia.
Our liability under this warranty is limited to the extent permitted by law. That is, to the extent
that it is fair and reasonable, if the Goods are not of a kind ordinarily acquired for personal,
domestic or household use or consumption, your remedies associated with any failure or defect
of the Product will be limited to:
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods;
(d) the payment of the cost of having the Goods repaired
and subject to the terms and conditions included in this warranty.
To ensure that service either pursuant to the above warranty or otherwise is readily available,
we have established in all States authorised service centres, which are available to deal with
service requirements.
For further information about your nearest service centre and other enquiries please call our
Service Centre on:
1300 650 644
1300 650 644
5. No other person, firm or corporation is authorised by us to offer or give on our behalf any
other or greater warranty than that given under this warranty. The benefits conferred by this
warranty are in favour of You and any person deriving title to the Goods through or under
such person and are intended to be separate from and additional to all other rights and
remedies that they may have in law in respect of the Goods.
6. In order to claim under the warranty granted under clause 1 you must:
(a) log a claim emailing [email protected], include the product serial number,
description of the fault and attach a copy of the original purchase invoice, within the Warranty
Period;
and
(b) return the Goods by prepaid freight within the Warranty Period, together with
i. the legible and unmodified proof of purchase, which clearly indicates your name and
address, the date of purchase, the product and model name, product serial number, and
ii. a copy of the completed Warranty Information page below. Please also provide your
daytime telephone number.
7. This warranty is only valid and enforceable in Australia.
Our liability under this warranty is limited to the extent permitted by law. That is, to the extent
that it is fair and reasonable, if the Goods are not of a kind ordinarily acquired for personal,
domestic or household use or consumption, your remedies associated with any failure or defect
of the Product will be limited to:
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods;
(d) the payment of the cost of having the Goods repaired
and subject to the terms and conditions included in this warranty.

SEELEY INTERNATIONAL – OWNER’S MANUAL 13
WARRANTY INFORMATION PAGE
Please retain your receipt as proof of purchase. Every request for warranty must be
accompanied by proof of purchase.
:
You can also register your warranty online by visiting www.seeleyinternational.com
and following these steps:
Step 1
Step 2
Step 3
Complete the following for your records:
:
: ...................................................................
...................................................................
...................................................................
: ....../....../......
Select ‘GET SUPPORT’ and ‘REGISTERAWARRANTY’
Select the brand of product you purchased
Enter the required information and then ‘Submit’
Serial Number:
Product
Model
Purchased from
Date purchased
Convair
Mastercool
Megacool H
PRIVACY NOTICE
Seeley International Pty Ltd ABN 23 054 687 035 will use the personal information you provide us with to provide
warranty support for the product you have purchased and to inform you about other products and services. If you
choose not to supply us with the information requested, we may be unable to provide you with warranty support. We
may also disclose your information to third parties, such as related entities; retailers, distributors, service agents and
contractors who are affiliated with us; or marketing or market research companies. If you would prefer not to receive
direct marketing communications from us, please follow the instructions to “unsubscribe” which will be included in
the direct marketing communications we send you, or contact our Privacy Officer using the details set out below.
While we do not currently transfer personal information to overseas recipients or store personal information
overseas, if we transfer your information to third parties who do so, we will take reasonable steps to ensure that
ottnesnocuoy,ytnarrawruoygniretsigeryB.ehthcaerbtonodstneipicersaesrevoeht
having your personal information used in this way. Please read our Privacy Policy on our website
www.seeleyinternational.com for further explanation of how we collect, use, hold and disclose personal information,
and how you may access and seek correction of your information. It also sets out how you may complain about a
breach of the Australian Privacy Principles, and how we will deal with your complaint. You may contact us at: Privacy
Officer, Seeley International Pty Ltd, 112 O'Sullivan Beach Road, Lonsdale, South Australia 5160.
Australian Privacy Principles
MIC, MICH Millenia MI, MIH
MIV, MIV
Service Department
Seeley International Pty Ltd
112 O'Sullivan Beach Road, Lonsdale, South Australia, 5160
Customer service centre in Australia: 1300 650 644
Website: www.seeleyinternational.com
SEELEY INTERNATIONAL – OWNER’S MANUAL 13
WARRANTY INFORMATION PAGE
Please retain your receipt as proof of purchase. Every request for warranty must be
accompanied by proof of purchase.
:
Please register your warranty online by visiting www.seeleyinternational.com
and following these steps:
Step 1
Step 2
Step 3
Complete the following for your records:
:
: ....../....../......
Select SERVICE & SUPPORT then REGISTER A PRODUCT FOR WARRANTY’
Enter your product serial number and “SUBMIT”
Enter the required information and “SUBMIT”
Serial Number:
Product
Model
Date purchased
Convair
Mastercool
Megacool
PRIVACY NOTICE
Seeley International Pty Ltd ABN 23 054 687 035 will use the personal information you provide us with to provide
warranty support for the product you have purchased and to inform you about other products and services. If you
choose not to supply us with the information requested, we may be unable to provide you with warranty support. We
may also disclose your information to third parties, such as related entities; retailers, distributors, service agents and
contractors who are affiliated with us; or marketing or market research companies. If you would prefer not to receive
direct marketing communications from us, please follow the instructions to “unsubscribe” which will be included in
the direct marketing communications we send you, or contact our Privacy Officer using the details set out below.
While we do not currently transfer personal information to overseas recipients or store personal information
overseas, if we transfer your information to third parties who do so, we will take reasonable steps to ensure that
ottnesnocuoy,ytnarrawruoygniretsigeryB.ehthcaerbtonodstneipicersaesrevoeht
having your personal information used in this way. Please read our Privacy Policy on our website
www.seeleyinternational.com for further explanation of how we collect, use, hold and disclose personal information,
and how you may access and seek correction of your information. It also sets out how you may complain about a
breach of the Australian Privacy Principles, and how we will deal with your complaint. You may contact us at: Privacy
Officer, Seeley International Pty Ltd, 112 O'Sullivan Beach Road, Lonsdale, South Australia 5160.
Australian Privacy Principles
MIC Millenia MI
MIV

Lorem ipsum
829524-G AU2307
It is the policy of Seeley International to introduce continuous product improvement.
Accordingly, specifications are subject to change without notice.
Please consult with your dealer to confirm the specifications of the model selected.
Warranty Registration
To register your warranty, go to
www.seeleyinternational.com