Seenergy SVR-204 User manual

4-Ch Network Video Recorder with HDMI
V 1 .0.0
SVR-204 Quick Guide

2"
[SVR'204"QUICK"GUIDE]!
Table of Contents
System Overview ..................................................................... 3
System Overview ..................................... Error! Bookmark not defined.
Front View .................................................................................... 3
Rear View ..................................................................................... 4
Illustration .................................................................................... 5
LED Definition ............................................................................... 5
Installation .............................................................................. 6
HDD Installation .............................................................................6
Connect to the NVR.......................................................................14
Use SEEnergy Device Search Utility ................................................ 14
Access the NVR with its default IP address....................................... 17
Set up Password .......................................................................... 19
Camera Installation ......................................................................20
Add a Camera -- Automatic Search................................................. 20
Add a camera manually ................................................................ 22

[SVR'204"QUICK"GUIDE]!
3
System Overview
Front View

4"
[SVR'204"QUICK"GUIDE]!
Rear View

[SVR'204"QUICK"GUIDE]!
5
Illustration
LED Definition

6"
[SVR'204"QUICK"GUIDE]!
Installation
HDD Installation
Locate the screws highlighted above on the back of the NVR.
Use a Philips screw driver to release the screws.

[SVR'204"QUICK"GUIDE]!
7
Slide open the case as shown above.
One side of the housing can be detached as shown above.

8"
[SVR'204"QUICK"GUIDE]!
Install the bottom HDD by slide it in to the tray diagonally to avoid the
tray seperator.
Once the HDD is placed into the tray, you should see a gap between
the HDD and the SATA connector.

[SVR'204"QUICK"GUIDE]!
9
Attach the HDD to the SATA connector by sliding it towards the
connector.
Make sure the screw holes on the HDD are aligned with the ones on
the tray.

10"
[SVR'204"QUICK"GUIDE]!
Secure the HDD with the screws provided in the accessory box with a
Philips screw driver. There are four for each HDD; two for each side of
the tray.
4-Ch
Network Video Recorder with HDMI
Install the top HDD by attaching it to the corresponding SATA cable
first.

[SVR'204"QUICK"GUIDE]!
11
Make sure the HDD is securely attached.
Place the HDD to the tray and make sure the screw holes on the HDD
are aligned with the ones on the tray.

12"
[SVR'204"QUICK"GUIDE]!
Secure the HDD with the screws provided in the accessory box with a
Philips screw driver. There are four for each HDD; two for each side of
the tray.
Slide the side housing back to the unit.

[SVR'204"QUICK"GUIDE]!
13
Secure the housing with the screws highlighted above.

14"
[SVR'204"QUICK"GUIDE]!
Connect to the NVR
There are various ways you can connect to the NVR and below are the
suggested methods for different network setup:
• The NVR is placed in a network with a DHCP server: Connect to
the NVR by using “SEEnergy Device Search” Utility
• The NVR is placed in a network without DHCP server (or you are
connecting to it directly): Access the NVR with its default IP
Use SEEnergy Device Search Utility
If the NVR is placed in a corporate network or a local area network
where a DHCP server is already presented, run the “SEEnergy Device
Search” utility from a computer that is on the same network and locate
the NVR with its IP address that is assigned by the top-level DHCP
server.

[SVR'204"QUICK"GUIDE]!
15
To begin, launch the “SEEnergy Deivce Search” utility from the CD and
proceed with the installation:

16"
[SVR'204"QUICK"GUIDE]!
Once the installation is complete, check the “Launch the Search AP”
option and click “Finish”.
The search should start automatically and its status should be dis-
played.
The NVR should be located and its IP address should be displayed.
Double-click on an NVR and the search program should automati- cally
access the NVR’s web administration page from your default browser.

[SVR'204"QUICK"GUIDE]!
17
You should be prompted for the the NVR’s username and password.
Enter its default username “admin” and password “admin” and then
click”OK” to enter the system
Access the NVR with its default IP address
The NVR comes with a pre-configured static IP “192.168.101.50”.
However, it is only used when there is no DHCP server presented in
the network. The NVR will turn on its DHCP server function and act as
the DHCP server in the network. To connect to the NVR, use a PC that
is on the same network over a switch or hub, or connect the PC
directly to the NVR using a crossover CAT5 Ethernet cable.

18"
[SVR'204"QUICK"GUIDE]!
The PC that is connected directly to the NVR (or within the same local
area network) should receive an IP from the NVR. Simply access the
NVR from your web browser with its IP address
Again, you should be prompted for the username and password. Enter
its default username “admin” and password “admin” and then
click”OK” to enter the system

[SVR'204"QUICK"GUIDE]!
19
Set up Password
The default login username and password is admin/admin. To change
the password of the admin account, go to “Setup” --> “System Con-
figurations” --> “User Account”, click on the “admin” account in the
account list then press the “edit” button to change its password.
Finally, click “Apply” to save the change.

20"
[SVR'204"QUICK"GUIDE]!
Camera Installation
Add a Camera -- Automatic Search
Click the “Search” button to perform the camera search.
You should be prompted to install Active Control component in order
for the search to function properly. Go ahead and click “Install”
After that, the search should begin and its status should be displayed: