SEI FA982500TX User manual

For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
FA982500TX
Moreno Fireplace Tower
-Mission Oak
Assembly Instructions
PO#:

A Quantity of 1
Top Panel
B Quantity of 1
Left Side Panel
C Quantity of 1
Right Side Panel
D Quantity of 1
Upper Back Panel
E Quantity of 1
Fixed Shelf Panel
F Quantity of 1
Bottom Panel
G Quantity of 1
Bottom Cross Panel
H Quantity of 2
Cross Panel
I Quantity of 2
Vertical Panel
J Quantity of 1
Back Panel
K Quantity of 1
Adjustable Shelf Panel
L Quantity of 2
Support Rail
M Quantity of 2
Wood Block
1 Quantity of 28
Cam Bolt ∮9/32”x1-1/2”L
2 Quantity of 28
Cam Lock ∮5/16”x1/2”L
3 Quantity of 28
Wood Dowel 5/16” x1-1/2”L
4 Quantity of 5
Screw ∮5/32”x1”L
5 Quantity of 4
Bolt ∮1/4”x1-1/4”L
6 Quantity of 4
Lock Washer ∮1/4”
Moreno Fireplace Tower-Mission Oak
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface
like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing. Before
beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures. Using the
incorrect hardware will cause damage.
.

7 Quantity of 4
Flat washer ∮1/4”x3/4”
8 Quantity of 1
Allen Wrench 1/4”
9 Quantity of 7
Screw ∮5/32”x1-1/4”L
10 Quantity of 14
Screw ∮1/8”x1/2”L
11 Quantity of 4
Shelf Holder
12 Quantity of 2
Anti-Tipping Hardware
13 Quantity of 1
Firebox (in a separate carton)
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required
No.2 Phillips Screwdriver
(not included)

Figure 1
Do not over tighten cam bolts,
please stop when you feel them tighten.
Insert cam locks (2) into holes on
vertical panel (I).
Screw cam bolts (1) into holes on right
side panel (C).Attach vertical panel (I)
to right side panel (C) by inserting wood
dowel (3) and cam bolts (1) into
corresponding holes until vertical panel
(I) and right side panel (C) meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
Figure 2
Insert cam locks (2) into holes on
vertical panel (I).
Screw cam bolts (1) into holes on left
side panel (B).Attach vertical panel (I)
to left side panel (B) by inserting wood
dowel (3) and cam bolts (1) into
corresponding holes until vertical panel
(I) and left side panel (B) meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
Moreno Fireplace Tower- Mission Oak
Assembly Instructions
( 2 )
(1)

Figure 3
Insert cam locks (2) into holes on cross
panel (H).
Screw cam bolts (1) into holes on top
panel (A).Attach cross panel (H) to top
panel (A) by inserting wood dowel (3)
and cam bolts (1) into corresponding
holes until cross panel (H) and top
panel (A) meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
Use screw (4) and wood dowels (3) to
connect top panel (A) to upper back
panel (D).
Tighten screw (4) with Philip
screwdriver.
Figure 4
Insert cam locks (2) into holes on cross
panel (H).
Screw cam bolts (1) into holes on fixed
shelf panel (E).Attach cross panel (H)
to fixed shelf panel (E) by inserting
wood dowels (3) and cam bolts (1) into
corresponding holes until cross panel
(H) and fixed shelf panel (E) meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
Use screws (9) and wood dowels (3) to
connect support rails (L) to shelf panel
(E).
Tighten screws (9) with Philips
screwdriver.

Figure 5
Use screws (9) and wood dowels (3) to
connect bottom cross panel (G) to
bottom panel (F).
Tighten screws (9) with Philips
screwdriver.
Figure 6
Insert cam locks (2) into holes on
assembled unit from figure 3 and
assembled unit from figure 5.
Screw cam bolts (1) into holes on right
side panel (C).
Attach assembled unit from figure 3 and
assembled unit from figure 5 to right
side panel (C) by inserting wood dowels
(3) and cam bolts (1) into corresponding
holes until assembled unit from figure 3,
assembled unit from figure 5, and right
side panel (C) meet.
Tighten by rotating cam locks (2)
clockwise with Phillips screwdriver.
Use bolts (5), lock washers (6), flat
washers (7), and wood dowels (3) to
connect assembled unit from figure 4 to
right side panel (C).
Tighten bolts (5) with Allen wrench (8).

Figure 7
Repeat last step to attach left side panel
(B) to assembled unit from figure 6.
Figure 8
Attach back panel (J) to assembled unit
with screws (10).
Tighten screws (10) with Phillips
screwdriver.
Insert firebox (13) into the back of the
unit. Make sure the firebox is pressed
tightly against the unit.
Attach wood blocks (M) to assembled
unit.
Use screws (4) to connect wood blocks
(M) to support rails.
Tighten screws (4) with Philips
screwdriver.

Figure 9
Insert shelf holders (11) into holes on
side panels.
Place adjustable shelf (K) onto the shelf
holder (11).
Make sure the shelf holder (11)
holds the shelf (K) firmly.
Figure 10
Attach anti-tipping hardware (12)
to the back of the upper back panel
(D) as shown in figure 10.
Tighten screws using Philips
screwdriver.
Mark two desired locations on wall and
drill two 3/16" holes.
Then, Insert plastic anchors into the two
holes on wall as shown.Attach the
anti-tipping hardware to the wall using
screws as shown.
Finally, move item close to the wall and
secure with plastic straps
Anti-tipping hardware must be used for
this product to avoid tipping and injury.

Figure 11
Now your Moreno fireplace tower is
ready for use.

Please immediately examine this product carefully. Any request for missing parts or damage replacement must
be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this
time frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying
product(s) and we are not responsible for any damages due to product modification(s). If damages or missing
parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement
merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at [e-mail]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019